• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.22-29
• /
• 1995

Lithium ionic solid electrolyte was synthesized at $60^{\circ}C$ in $N_{2}$ ambience by sol-gel method, using tetraethyl orthosilcate, lithium methoxide, zirconium n-propoxide, and tributyle phosphate as precursors. The prepared material was dried and crushed into powder, and it was pressed into disk type samples. These samples were sintered at $900^{\circ}C{\sim}1100^{\circ}C$ for 50 hours. The physical characteristics of the samples were investigated by TG/DTA, SEM, AES and XRD methods. $CO_{2}$ sensor based on lithium ionic solid electrolyte was fabricated and its operational characteristics were measured. The sensing characteristics of the sensor sintered at $1000^{\circ}C$ shows the variation of e.m.f. about $35{\sim}63\;mV/decade$ for the variation of $CO_{2}$ concentration at $200^{\circ}C{\sim}300^{\circ}C$ of operating temperature, and good linearity for $300{\sim}6000\;ppm$.

• Membrane Journal
• /
• v.25 no.5
• /
• pp.456-463
• /
• 2015

In this study, we synthesize novel silane based inorganics for preparation of the polymer electrolyte membrane with high proton conductivity under high temperature condition and developed membranes are characterized. SPAES, hydrocarbon based polymer are synthesized and used as main polymeric material. We used sol-gel method to prepare inorganic material with high performance using silica, phosphate and zirconium. Three types of inorganics were prepared by control of the mole ration of each component. As a result of EDX analysis, the inorganic materials are well dispersed in the polymer membrane. The water uptake of the composite membrane is increased by introduction of the hydrophilic inorganic material in the membrane. When the content of the zirconium in the membrane is increased, the proton conductivity of the composite membrane shows the higher value than pure SPAES membrane at the high temperature. And the silica based inorganics effect to increase the proton conductivity under low temperature condition.

• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.85-89
• /
• 2009

Nano-crystalline hydroxyapatite (HAp) films were formed at the Ti surface by a single-step microarc oxidation (MAO), and HAp-zirconia composite (HZC) films were obtained by subsequent chemical vapor deposition (CVD) of zirconia onto the HAp. Through the CVD process, zero- and one-dimensional zirconia nanostructures having tetragonal crystallinity (t-ZrO2) were uniformly distributed and well incorporated into the HAp crystal matrix to form nanoscale composites. In particular, (t-$ZrO_2$) was synthesized at a very low temperature. The HZC films did not show secondary phases such as tricalcium phosphate (TCP) and tetracalcium phosphate (TTCP) at relatively high temperatures. The most likely mechanism for the formation of the t-$ZrO_2$ and the pure HAp at the low processing temperature was proposed to be the diffusion of $Ca^{2+}$ ions. The HZC films showed increasing micro-Vickers hardness values with increases in the t-$ZrO_2$ content. The morphological features and phase compositions of the HZC films showed strong dependence on the time and temperature of the CVD process. Furthermore, they showed enhanced cell proliferation compared to the $TiO_2$ and HAp films most likely due to the surface structure change.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.6
• /
• pp.475-483
• /
• 2015

PURPOSE. The objective of this study was to evaluate the influence of various cement types on the stress distribution in monolithic zirconia crowns under maximum bite force using the finite element analysis. MATERIALS AND METHODS. The models of the prepared #46 crown (deep chamfer margin) were scanned and solid models composed of the monolithic zirconia crown, cement layer, and prepared tooth were produced using the computer-aided design technology and were subsequently translated into 3-dimensional finite element models. Four models were prepared according to different cement types (zinc phosphate, polycarboxylate, glass ionomer, and resin). A load of 700 N was applied vertically on the crowns (8 loading points). Maximum principal stress was determined. RESULTS. Zinc phosphate cement had a greater stress concentration in the cement layer, while polycarboxylate cement had a greater stress concentration on the distal surface of the monolithic zirconia crown and abutment tooth. Resin cement and glass ionomer cement showed similar patterns, but resin cement showed a lower stress distribution on the lingual and mesial surface of the cement layer. CONCLUSION. The test results indicate that the use of different luting agents that have various elastic moduli has an impact on the stress distribution of the monolithic zirconia crowns, cement layers, and abutment tooth. Resin cement is recommended for the luting agent of the monolithic zirconia crowns.

• Journal of Periodontal and Implant Science
• /
• v.52 no.3
• /
• pp.242-257
• /
• 2022

Purpose: This study investigated periodontal ligament (PDL) restoration in osseointegrated implants using stem cells. Methods: Commercial pure titanium and zirconium oxide (zirconia) were coated with beta-tricalcium phosphate (β-TCP) using a long-pulse Nd:YAG laser (1,064 nm). Isolated bone marrow mesenchymal cells (BMMSCs) from rabbit tibia and femur, isolated PDL stem cells (PDLSCs) from the lower right incisor, and co-cultured BMMSCs and PDLSCs were tested for periostin markers using an immunofluorescent assay. Implants with 3D-engineered tissue were implanted into the lower right central incisors after extraction from rabbits. Forty implants (Ti or zirconia) were subdivided according to the duration of implantation (healing period: 45 or 90 days). Each subgroup (20 implants) was subdivided into 4 groups (without cells, PDLSC sheets, BMMSC sheets, and co-culture cell sheets). All groups underwent histological testing involving haematoxylin and eosin staining and immunohistochemistry, stereoscopic analysis to measure the PDL width, and field emission scanning electron microscopy (FESEM). The natural lower central incisors were used as controls. Results: The BMMSCs co-cultured with PDLSCs generated a well-formed PDL tissue that exhibited positive periostin expression. Histological analysis showed that the implantation of coated (Ti and zirconia) dental implants without a cell sheet resulted in a well-osseointegrated implant at both healing intervals, which was confirmed with FESEM analysis and negative periostin expression. The mesenchymal tissue structured from PDLSCs only or co-cultured (BMMSCs and PDLSCs) could form a natural periodontal tissue with no significant difference between Ti and zirconia implants, consequently forming a biohybrid dental implant. Green fluorescence for periostin was clearly detected around the biohybrid implants after 45 and 90 days. FESEM showed the invasion of PDL-like fibres perpendicular to the cementum of the bio-hybrid implants. Conclusions: β-TCP-coated (Ti and zirconia) implants generated periodontal tissue and formed biohybrid implants when mesenchymal-tissue-layered cell sheets were isolated from PDLSCs alone or co-cultured BMMSCs and PDLSCs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.4
• /
• pp.154-159
• /
• 2019

The glass-ceramic of $Li_2O-Al_2O_3-SiO_2$ system was fabricated by using yttrium oxide and iron oxide that it can reduce the melting temperature and affect the homogenization. Zirconium sulfate was used as a nucleation agent. Calcium phosphate was used to improve the flow the glass so as reduce the viscosity of the glass. The glass-ceramics met a thermal shock test of more than $750^{\circ}C$ and the temperature at which the coefficient of thermal expansion rapidly increased at over $800^{\circ}C$ was shifted by about the above $30^{\circ}C$. Therefore, it is concluded that the glass-ceramic of $Li_2O-Al_2O_3-SiO_2$ system with yttrium oxide and iron oxide was founded to have good melting conditions and excellent thermal expansion resistance at high temperature such as special field for kitchen utensils.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.267-271
• /
• 2003

In this work, chemical solution derived Ca-doped zirconia fiber has been prepared by using calcium- and zirconium-naphthenate. Fibrous $ZrO_2$-CaO was drawn from a sticky mixture. Dried gel fibers were finally annealed at $1000^{\circ}C$ for 1 h in argon. 91 mol%$ZrO_2$-9 mol%CaO fiber consisted of tetragonal, monoclinic and $CaZrO_3$ phases after annealing at $1000^{\circ}C$. On the other hand, samples annealed at $500^{\circ}C$ consisted of almost tetragonal single phase. Homogeneous fibers surface at $500^{\circ}C$ became rougher after $1000^{\circ}C$-annealing. The sample annealed at $1000^{\circ}C$ with relatively rough surface structure showed a high Calcium phocphate forming ability.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.571-576
• /
• 2015

In this study, we developed a lead-free $P_2O_5-V_2O_5-ZnO$ glass frit for sealing OLED using laser irradiation. The frit satisfied the characteristics required for laser sealing such as low glass transition temperature, low coefficient of thermal expansion (CTE), high water-resistance, and high absorption at the wavelength of the laser beam. Ceramic fillers were added to the glass frit in order to further reduce and match its CTE with that of the commercial glass substrate. The addition of Zirconium Tungsten Phosphate (ZWP) to the frit yielded the most desirable results, reducing the CTE to $45.4{\times}10^{-7}/^{\circ}C$, which is very close to that of the glass substrate ($44.0{\times}10^{-7}/^{\circ}C$). Successful formation of a solid sealing layer was observed by optical and scanning electron microscopy.

• Korean Journal of Materials Research
• /
• v.13 no.2
• /
• pp.115-119
• /
• 2003

The thick film type sensor having Pt/Na Super Ionic Conductor(NASICON) solid electrolyte/Pt/$Na_2$$SO_4$/Pt catalyst system for $SO_2$gas was fabricated by screen-print method. The phase of Na Super Ionic Conductor solid electrolyte sintered at different temperature of 1050, 1150,$ 1250^{\circ}C$ and for different time of 1.5, 2.5, 3.5 hr were investigated by XRD. The Electromotive Force variation of the sensor with $SO_2$concentrations and operating temperatures were investigated. The major phase of Na Super Ionic Conductor film sintered at 115$0^{\circ}C$ for 3.5 hr was sodium zirconium silicon phosphate($Na_3$Zr$_2$$Si_2$PO$_{12}$). The Nernst's slope of Na Super Ionic Conductor sensor for $SO_2$gas with the variation of concentration from 10 to 100 ppm was 167.14 ㎷/decade at the operating temperature of $500 ^{\circ}C$. The increase of oxygen partial pressure was not affected to the variation of Nernst's slope.e.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.269-273
• /
• 2002

The NASICON solid electrolyte films, $Na_{1+x}Zr_2Si_xP_{3-x}O_{12}$(1.5< x < 2.3), was prepared from ceramic slurry by modified doctor-blade process. The NASICON solid electrolyte and fabricated sensors, Pt-electrode/NASICON/Carbonate$(Na_2CO_3-K_2CO_3CaCO_3\; system)$ electrode, were investigated to measure phase, microstructure and e.m.f variation for sensing $CO_2$ concentration. The uniform grain size of $2-4{\mu}m$ and major phase of sodium zirconium silicon phosphate phase, $Na_{1+x}Zr_2Si_xP_{3-x}O_{12}$was identified with X-ray diffraction patterns and scanning electron microscopy, respectively. The Nernst's slope of 84 mV/decade for $CO_2$ concentration from 500 to 8000 ppm was obtained at operating temperature of $400^{\circ}C$.