• ETRI Journal
• /
• v.28 no.4
• /
• pp.533-536
• /
• 2006

A distributed Bragg reflector (DBR) laser and a high speed electroabsorption modulator (EAM) are integrated on the basis of the selective area growth technique. The typical threshold current is 4 to 6 mA, and the side mode suppression ratio is over 40 dB with single mode operation at 1550 nm. The DBR laser exhibits 2.5 to 3.3 mW fiber output power at a laser gain current of 100 mA, and a modulator bias voltage of 0 V. The 3 dB bandwidth is 13 GHz. A 10 Gbps non-return to zero operation with 12 dB extinction ratio is obtained. A four-channel laser array with 100 GHz wavelength spacing was fabricated and its operation at the designed wavelength was confirmed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.301-302
• /
• 2006

초고주파 전력 증폭기의 바이어스 전압을 조절하여 온도 변화에 따른 드레인(Drain) 전류의 변화를 억제하기 위한 저가의 능동 바이어스 모듈을 개발한다. 능동 바이어스 모듈을 5 W급 초고주파 전력증폭기에 적용하였을 경우, $0{\sim}60^{\circ}C$까지의 온도변화에 대하여 소모전류 변화량은 0.1 A 이하로 되어야 한다. 본 기술 개발 대상인 능동 바이어스 모듈의 성능 시험을 위한 대상 전력증폭기는 $2.11{\sim}2.17GHz$ 주파수 대역에서 32 dB 이상의 이득과 ${\pm}0.1\;dB$ 이하의 이득 평탄도, -15 dB 이하의 입.출력 반사손실을 가진다.

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.91-96
• /
• 2011

In this paper, we propose a microstrip bandpass filter using stepped-impedance coupled-line hairpin resonators. The stepped-impedance coupled-line hairpin resonator has extended harmonic suppression in comparison with a conventional hairpin resonator due to transmission zero and the movement of harmonic frequencies resulting from the stepped-impedance characteristic. A high-pass type impedance/admittance inverter is employed in order to improve the lower frequency skirt characteristics of the passband. A 4-pole bandpass filter is designed and fabricated at 1.8 GHz. The measured results show the excellent attenuation performance at the stopband which is greater than 30 dB up to 10 GHz.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.9
• /
• pp.448-453
• /
• 2003

In this paper the controlled closing algorithm of the circuit breaker for isolated capacitor banks is proposed. The characteristics of circuit breakers such as RDDS(rate of decrease of dielectric strength) and a mechanical operating tolerance should be also taken into account to locate contact touch instants around voltage zero. The analysis results on the voltages across circuit breaker terminals upon closing operation play an important roles to describe the suggested method. The simulations carried out in order to verify the performance of this method show that the closing instants obtained from the proposed method provide a good suppression effect on the closing transients for both single and back-to-back capacitor banks.

• Investigative Magnetic Resonance Imaging
• /
• v.20 no.1
• /
• pp.27-35
• /
• 2016

Purpose: Among RF pulses, a sinc pulse is typically used for slice selection due to its frequency-selective feature. When a sinc pulse is implemented in practice, it needs to be apodized to avoid truncation artifacts at the expense of broadening the transition region of the excited-band profile. Here a sinc pulse tailored by a new apodization function is proposed that produces a sharper transition region with well suppression of truncation artifacts in comparison with conventional tailored sinc pulses. A multiband pulse designed using this newly apodized sinc pulse is also suggested inheriting the better performance of the newly apodized sinc pulse. Materials and Methods: A new apodization function is introduced to taper a sinc pulse, playing a role to slightly shift the first zero-crossing of a tailored sinc pulse from the peak of the main lobe and thereby producing a narrower bandwidth as well as a sharper pass-band in the excitation profile. The newly apodized sinc pulse was also utilized to design a multiband pulse which inherits the performance of its constituent. Performances of the proposed sinc pulse and the multiband pulse generated with it were demonstrated by Bloch simulation and phantom imaging. Results: In both simulations and experiments, the newly apodized sinc pulse yielded a narrower bandwidth and a sharper transition of the pass-band profile with a desirable degree of side-lobe suppression than the commonly used Hanning-windowed sinc pulse. The multiband pulse designed using the newly apodized sinc pulse also showed the better performance in multi-slice excitation than the one designed with the Hanning-windowed sinc pulse. Conclusion: The new tailored sinc pulse proposed here provides a better performance in slice (or slab) selection than conventional tailored sinc pulses. Thanks to the availability of analytical expression, it can also be utilized for multiband pulse design with great flexibility and readiness in implementation, transferring its better performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.385-394
• /
• 2006

The application areas of traditional push-pull converters are limited because the voltage stress of switches is high (twice of the input voltage). But the push - pull converter topology is suitable for unregulated low-voltage to high-voltage power conversion such as the fuel cell. This paper presents a novel power converter structure that is very suitable for the DC/DC converter in fuel cell systems. Based on this structure, a ZVS- ZCS push-pull converter is proposed. The switches of the proposed push-pull converter can operate under ZVS or ZCS condition with the help of a new passive clamping circuit. The passive clamping techniques solves the voltage overshoot problem. Because the buck converter circuit operates at twice the synchronous switching frequency of the push-pull converter, the peak current in the current-fed inductor and transformer is reduced. The operation principle of the proposed converter is analyzed and verified by simulations and experimental results. A 1 kW DC/DC converter was implemented with DSP TMS320F2812, from which experimental results have shown that efficiency improvement and surge suppression can be achieved effectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.4
• /
• pp.299-309
• /
• 2014

When biped robots make turns, the ability to walk stably and precisely along any circular path is crucial. In this context, inverse kinematics solutions are found for accurate gait realization, and new zero moment point(ZMP) equations are derived with respect to the cyclindrical coordinate system to facilitate generation of stable walking patterns. Then, appropriate steady and transitional walking patterns are both proposed in form of time functons. Subsequently, walking patterns for a path but of different speeds are generated using the functions and associated formulas, and preliminarily checked for stability based on the ZMP equations. Upon comparison of those cases, one can see how and when robots may fall down during circular walking. Finally, those patterns are put to test on the sample robot by ADAMS(R) along with the inverse kinematics solutions and a new balance control scheme compensating for insufficient stability particulary during the initial transition period. Test results show that the robot can walk along the circular path as predicted at a resonably high speed despite the distributed mass and ground contact effects, validating effectiveness of the suggested approach.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.8A
• /
• pp.768-776
• /
• 2010

In this paper, we consider a linear precoding for the effective spectrum sharing in multiple-input multiple-output (MIMO) cognitive radio system where a secondary user coexists with primary users. The secondary user employs the orthogonal space time block coding (OSTBC) at the transmitter. Assuming a flat fading channel and a maximum-likelihood receiver, the optimum precoder forces transmission referred to as eigen-beamforming. In this paper, to eliminate the interference, ZF criterion based eigen-beamforming is not only used but also the precoding weight is chosen to cancel the remaining interference. This weight is computed by vector's likelihood. Simulation results show stronger interference suppression capability, better SER performance, and higher capacity than the algorithm in [4].

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.6
• /
• pp.1153-1160
• /
• 2003

In this paper, the performance of the UWB communication systems is analyzed in the presence of the Narrow Band Interference(NBI). UWB communication systems are modeled as using the Pulse Position Modulation(PPM). In this system, a Gaussian monocycle is used as the received pulses. The NBI is considered as a zero-mean random process with a constant spectral power density over its whole bandwidth. We obtain the mathematical expressions for describing the effect of the NBI on the UWB system. And it can be shown that the suppression of the effect of NBI on the UWB systems is available by adjusting the PPM related parameter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.3
• /
• pp.225-230
• /
• 2018

This paper proposes a parametric design of an LLC resonant inverter used for a microwave oven. To improve the harmonic performance of the microwave oven, a current controller with a variable PI gain is proposed. Due to the recent strengthening of harmonics regulations, inverter control technology for microwave ovens is now required to satisfy harmonic performance. In an LLC resonant inverter, the voltage gain varies remarkably depending on the magnetron voltage, output power, and input voltage. To satisfy harmonic performance, a controller that can maintain operation in the zero-voltage switching (ZVS) region and control changes in voltage gain is required. The modified design of the LLC resonant inverter ensures ZVS operation even when the magnetron is heated. Application of the variable current controller improves harmonic control according to the instantaneous gain curve change. The validity of the proposed power control with a variable current controller is verified by experiments with a 1200 W microwave oven.