• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.3-9
• /
• 1984

This study was carried out to examine the practicality of DAP[$(NH_4)_2HPO_4$] as fire retardant for plywood by static bending test the redried plywoods which had been soaked in 20% $(NH_4)_2HPO_4$ solution. Being hot/cold soaked in the solution for 3/3, 6/3, 9/3 and 12/3 hours and redried by cyclic press-drying method at the platen temp. of 130, 145, 100 and $175^{\circ}C$, the treated plywoods were tested to offer the mechanical data, that is, $S_{pl}$(stress at proportional limit), MOE(modulus of elasticity), MOR(modulus of rupture) and $W_{pl}$(work per unit volume to proportional limit ) in flexure. The results obtained were summarized as follows. 1. $S_{pl}$ of fire retardant treated plywoods ("FRP" would be used hereinafter) decreased as the platen temperature increased, but it was superior to that of non-treated plywoods(Control) at $160^{\circ}C$ or higher. 2. MOE of FRP decreased roughly with the increase of temperature, hut this tendency was not constant. And the value of FRP was higher than that of Control even at $175^{\circ}C$. 3. MOR of FRP showed same temperature-dependent tendency as MOE, but it was influenced more sensitively at the higher temperature. 4. $W_{pl}$ of FRP also decreased gradually with the increase of platen temperature and the value in DAP 9/3 treatment was Jess than 70% of control plywoods. 5. In view of redrying time and mechanical properties, the most reasonable platen temperature for DAP treated FRP was $160^{\circ}C$ in this study.

• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.10-19
• /
• 1984

The $3{\times}3{\times}30$ ($cm^3$) sized lumbers of Populus alba-grandulosa L. were treated with four fire-retardant solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate and aluminium chloride for 1, 15, 30, and 60 minutes and 1, 3, and 7 days. Thereafter they were air-dried and burned at high temperature about $1,800^{\circ}C$ and for short time of five minutes. This study estimated the relationship between absorbed chemical amounts and rate of weight loss or residual bending strength of these burned lumbers. The results were as follows: 1) In absorption amount of fire-retardant chemicals, diammonium phosphate showed the largest, aluminium chloride the smallest, but monoammonium phosphate and ammonium sulfate showed similar level. 2) The absorption amount of chemicals was decreased with the increase of specific gravity in the same species except aluminium chloride. 3) The rate of weight loss was decreased as the absorption amount of chemicals increased, especially monoammonium phosphate was most effective. 4) The MOR value of the residual bending strength was increased as the absorption amount of chemicals increased and especially monoammonium phosphate showed the most efficient effect. 5) Aluminium chloride showed more striking increase of MOR value of residual bending strength with the increase of absorption amount than any other chemical, therefore its MOR value was similar to the maximum MOR value of the most effective monoammonium phosphate. 6) The correlation between weight loss and MOR value of the residual bending strength was negative and aluminium chloride showed the most striking negative relation, but the others showed similar trends. 7) The correlation between work to proportional limit and absorption amount of chemicals was positive and the degree of increase in work to proportional limit was most in aluminium chloride, and the next, in monoammonium phosphate and diammonium phosphate in turn. 8) The correlation between work to maximum load and absorption amount of chemicals showed positive and diammonium phosphate revealed the best result and aluminium chloride showed better results than other two chemicals.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• Journal of the Korean Wood Science and Technology
• /
• 제13권4호
• /
• pp.67-72
• /
• 1985

To improve the bending strength of sawdustboard, verious resin contents of 10, 13, 16, and 19% were applied to the thin shell (face layer) composed with wire net or not. The shell effect of sawdust and wire net composition formed with core sawdustboard were evaluated. Forcusing on the effects of wire net composition and noncomposition including a comparison with chipboard and veneer complyboard, bending properties (Modulus of rupture (MOR), Modulus of elasticity (MOE), Stress at proportional limit ($S_{pl}$). Work to maximum load ($W_{ml}$))were analyzed and discussed. 1. In modulus of rutpute, veneer comply was the highest (621.5 kg/$cm^2$), and next decreasing order was wire net composition (159.1 kg/$cm^2$), chipboard (81.75 kg/$cm^2$), and wire net noncomposition (76.21 kg/$cm^2$) as in modulus of elasticity, work to maximum load, except for stress at proportional limit. 2. The highly significant effects were shown in both wire net composition and noncomposition, at the same time wire net composition exceeded two times of noncomposition throughout resin contents in bending properties. Chipboard was similar to the mean or 16% resin content in noncomposirion. 3. Every board in wire net composition above 10% resin content was beyond 100 kg/$cm^2$ in MOR, minimum allowable strength for structural use according to KS F 3104. In conclusion, the feasibility for improving the bending strength of weak sawdustboard by wire net composed shell was offered.

• Journal of the Korean Wood Science and Technology
• /
• 제12권4호
• /
• pp.12-18
• /
• 1984

열판온도(熱板溫度)가 내화약제(耐火藥劑)로 처리(處理)된 합판(處理)의 재건조(再乾燥) 후(後) 곡강도(曲强度)에 미티는 영향(影響)을 조사(調査)하기 위해 두께 3.5mm 메란티합판(合板)을 황산(黃酸)암모늄, 제1(第一)인산암모늄, 제2인산(第二燐酸)암모늄 그리고 혼합약제(混合藥劑)인 붕사(硼砂) 붕산(硼酸) 및 미나리스 등(等) 5종(種)의 내화제(耐火劑)의 20% 수용액(水溶液)에 9시간(時間)동안 침지처리(浸漬處理)한 다음, 각각(各各) 열판온도(熱板溫度) $90^{\circ}C$, $120^{\circ}C$ 및 $150^{\circ}C$를 적용(適用)한 단계별(段階別) 건조방식(乾燥方式)으로 건조(乾燥)하여 곡강도시험(曲强度試驗)을 행(行)하였다. 비례한계(比例限界)에서의 응력(應力), 탄성계수(彈性係數), 파괴계수(破壞係數) 및 비례한계(比例限界)까지의 단위체적당(單位體積當) 일 등(等)을 조사(調査)한 바, 수분처리대조구(水分處理對照區)의 경우, 열판온도(熱板溫度) $120^{\circ}C$까지 유지(維持)되던 강도(强度)가 $150^{\circ}C$에 이르러서는 현저한 감소경향(減少傾向)을 나타내었으나, 내화약제처리합판(耐火藥劑處理合板)은 $150^{\circ}C$까지 열판온도(熱板溫度)가 상승(上昇)함에도 불구(不拘), 강도(强度)가 유지(維持)되었으며 일부 약제처리(藥劑處理)의 경우엔 오히려 증가(增加)하는 양상(樣相)도 보여주었다. 건조속도(乾燥速度)와 강도유지(强度維持)의 측면(側面)을 고려할 때, 바람직한 열판건조온도(熱板乾燥溫度)는 $150^{\circ}C$ 였으며 내화약제중(耐火藥劑中) 보강효과(補强效果)가 가장 좋은 약제(藥劑)는 붕사(硼砂) 붕산(硼酸)이었다.

• Journal of the Korean Wood Science and Technology
• /
• 제12권2호
• /
• pp.20-26
• /
• 1984

내화처리(耐火處理)된 합판(合板)의 내부(內部)에 잔존(殘存)하고 있는 내화약제(耐火藥劑)의 종류(種類) 및 그 양(量)이 합판(合板) 특유(特有)의 장점(長點)인 휨 강도(强度)에 어떠한 영향(影響)을 미치는 가를 조사(調査)하기 위(爲)해 황산(黃酸) 암모늄(Ammonium sulfate), 제1인산(第一燐酸) 암모늄(Ammonium phosphate, mono basic), 제2인산(第二燐酸) 암모늄(Ammonium phosphate, di basic), 그리고 복합약제(複合藥劑)인 붕사(硼砂) 붕산(硼酸)(Borax-Boric acid) 및 미나리스(Minalith) 등(等) 5종(種)의 내화제(耐火劑)를 20% 수용액(水溶液)으로 조제(調劑)한 다음 3.5mm 메란티 합판(合板)을 3시간(時間)부터 12시간(時間) 동안 3시간(時間) 간격(間隔)으로 침지처리(浸漬處理)를 한 후(後) $120^{\circ}C$의 열판(熱板)으로 재건조(再乾燥)하여 휨 강도시험(强度試驗)을 행(行)하였다. 비례한계(比例限界)에서의 응력(應力), 탄성계수(彈性係數), 파괴계수(破壞係數) 및 비례한계(比例限界)까지의 단위체적(單位體積) 당(當) 일등(等)을 조사(調査)한 바, 약제처리(藥劑處理)한 합판(合板)의 경우가 수분처리합판(水分處理合板)(대희구(對熙區))에 비(比)해 대부분(大部分) 높게 나타났으며 붕사(硼砂) 붕산(硼酸) 처리합판(處理合板)의 경우가 4부간(部間)에서 공(共)히 가장 높은 치(値)를 보여주었다. 그리고 처리시간(處理時間)이 연장(延長)됨에 따라, 즉 약액(藥液)의 흡수량(吸收量)(약제(藥劑) 잔존량(殘存量))이 증가(增加)함에 따라 휨 강도(强度)는 대체적(大體的)으로 향상(向上)하는 것으로 나타났다. 강도적(强度的) 측면(側面)이나 침지처리시(浸漬處理時) 발생(發生)하는 결함(缺陷) 등을 고려(考慮)할 때 복합약제(複合藥劑)인 붕사(硼砂) 붕산(硼酸)이 가장 바람직한 합판용(合板用) 내화처리약제(耐火處理藥劑)로 사료되는 바이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.606-611
• /
• 2000

It has been noted that the low frequency absorption coefficient of a porous sample placed in a standing wave tube is affected by the nature of the sample's edge constraint. The edge constraint has the effect of stiffening the solid phase of the sample, which itself can be strongly coupled to the material's fluid phase, and hence the incident sound field, by viscous means at low frequencies. In recent work it has also been shown that such a circumferential constraint causes the low frequency transmission loss of a layer of fibrous material to approach a finite low frequency limit that is proportional to the flow resistance of the layer and which is substantially higher than that of an unconstrained sample of the same material. However, it was also found that the benefit of the circumferential edge constraint was reduced in a transitional frequency range by a shearing resonance of the sample. Here it will be shown that the effect of that resonance can be mitigated or eliminated by adding additional axial and radial constraints running through the sample. It will also be shown that the constraint effect can be modeled closely by using a finite element procedure based on the Biot poroelastic theory. Implications for low frequency barrier design are also discussed.

• 한국사회복지학
• /
• 제68권3호
• /
• pp.51-71
• /
• 2016

이 연구의 목적은 한국을 포함한 OECD 주요국을 대상으로 사회구조적 요인, 복지제도, 노동시장 및 정치제도 등 독신모가구 빈곤의 국가 간 다양성에 영향을 끼치는 거시적 원인을 규명하는 것이다. 1981년부터 2012년 기간에 대해 불균형패널설계(unbalanced panel design)방법을 적용한 결합시계열회귀분석을 실시했다. 연구결과 독신모가구의 빈곤율은 국가 간 다양성이 현저했다. 1인당GDP는 빈곤위험감소에 기여하지 못했고, 여성고용율과 15세미만 아동비율은 빈곤위험을 증가시켰다. 전체사회복지지출, 아동에 대한 현금지출, 노조조직률, 정규직에 대한 고용보호, 비례대표선거제도, 누적좌파내각, 누적여성의석수는 독신모가구의 빈곤위험을 감소시키는 요인으로 나타났다. 한국은 경제성장 일변도와 노동시장유연화 위주의 탈빈곤전략에서 탈피해 보편적 복지제도, 아동에 대한 복지급여와 일-가정양립정책을 확대할 필요가 있다. 나아가 노조조직률향상과 고용보호확대 등 조정된 노동시장제도를 설계하고, 비례대표선거제도 등 합의제정치모델을 도입해 좌파정치세력과 여성의 정치적 대표성을 확립할 필요가 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제12권3호
• /
• pp.15-24
• /
• 1984

The $3{\times}3{\times}30\;cm^3$ sized specimens of Douglas-fir(Pseudotsuga menziesii) and western hemlock(Tsuga heterophylla) in this study were soaked in four fire-retardant solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate, and aluminium chloride for 1, 24, 72, 168, and 336 hours. Subsequently they were air-dried and burned at high temperature of ca. $1,800^{\circ}C$ and for short time of 5 minutes. This study estimated the relationship between the adsorbed chemicals and the residual weight ratio or residual bending strength of these partly burned lumbers. The results were as follows; 1) In average amount of chemical adsorption, diammonium phosphate showed the largest and aluminium chloride the smallest regardless of species but monoammonium phosphate was larger in Douglas-fir than that of western hemlock. 2) The amount of chemical adsorption was larger in western hemlock than Douglas-fir on the whole. 3) The amount of chemical adsorption was increased with the increase of soaking time but the rate of increase began to decrease at 200hrs. 4) Residual weight ratios showed no difference between species but showed differences among the chemicals treated i.e. monoammonium phosphate, diammonium phosphate, ammonium sulfate and aluminium chloride in turn from the largest to the smallest. 5) MOR values showed linear increase with the increase of residual weight ratios but showed no difference in species and chemicals respectively. 6) In the relationship between amount of chemical adsorption and MOR, only diammonium phosphate showed the curve of secondary degree with significance in Douglas-fir. 7) The MOE value of burned Douglas-fir lumber increased and showed significance of 99% as the adsorbed chemical amount increased, but among the chemicals only monoammonium phosphate showed significance. The MOE value of burned western hemlock lumber didn't show significance. 8) In only Douglas-fir, the correlation between adsorbed chemical amount and work to proportional limit showed significance in only monoammonium phosphate. And in both Douglas-fir and western hemlock, the correlation between adsorbed chemicals and work to maximum load showed significance in monoammonium phosphate.

• Journal of the Korean Wood Science and Technology
• /
• 제15권3호
• /
• pp.44-55
• /
• 1987

In order to study the effect of sawdustboard combined with plastic chips, 0.5mm($T_1$), 1mm($T_2$), 1.4mm($T_3$) thick nylon fiber. polypropylene rope fiber(RP), and 0.23mm thick moth-proof polypropylene net fiber(NP) were cut into 0.5, 1, 2cm long plastic chips. Thereafter, sawdustboard combined with plastic chips prepared as the above and plastic non-combined sawdustboard(control) were manufactured into 3 types of one-, two-, and three layer with 5 or 10% combination level. By the discussions and results at this study, the significant conclusions of mechanical and physical properties were summarized as follows: 1. The MORs were shown in the order of 3 layer> 2 layer> 1 layer among plastic non-combined boards, and $T_3$ < $T_2$ < $T_1$ < RP (NP(5%) < NP(l0%) among plastic combined boards. In 2cm long plastic chip in 1 layer board, the highest strength through all the composition was recognized. 1 layer board showing the lower strength with 0.5cm plastic chip rendered to the bending strength improvement by 2 or 3 layer board composition. On the other hand, 2 or 3 layer combined with 1, 2cm long polypropylene net fiber chips incurred MOR's conspicuous decrease requiring optimum plastic chip combined level and consideration to combined type. 2. MOE in plastic non-combined 3 layer board exhibited sandwich construction effect by higher resin content application to surface layer in the order of 3layer>1layer>2layer with the highest stiffness of the board combined with polypropylene chip, while nylon chip-combined board had little difference from plastic non-combined board. In relevant to length and layer effect, 3 layer board combined with the 0.5cm long polypropylene net fiber chip in 5% and 10% combined level presented 34-43% and 44-76% stiffness increase against plastic non-combined board(control), respectively. Moreover, in 1 layer board, 30% stiffness increase with 10% against 5% combined level in the 1 and 2cm long polypropylene net fiber chip was obtained. 3. Stress at proportional limit(Spl) showing the fiber relationship (r: 0.81-0.97) between MOR presented in the order of 1 layer<2 layer<3 layer in plastic non-combined board. Correspondingly, combined effect by layer and plastic chip length was similar to MOR's. 4. Differently from previous properties(MOR, MOE, Spl). work to maximum load(Wml) of 2 layer board approached to that of 3 layer board. Conforming the above phenomenon. 2 layer combined with 0.5cm long polypropylene net fiber chip kept the greater work than 1 layer. The polypropylene combined board superior to nylon -and plastic non - combined board seemed to have greater anti - failing capacity. 5. Internal bond strength(IB), in contrast to MOR's tendency. showed in the order of T1