• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.326-332
• /
• 2011

Radial variation of sound absorption capability and air permeability of yellow poplar (Liriodendron tulipifera) wood in cross sectional surface and effect of steam explosion treatment were estimated by the two microphone transfer function method and the capillary flow porometry, respectively. The sound absorption coefficients of steam explosion treated wood was higher than those of control wood and these values increased with frequency. Abundant and big vessel may behave as sound absorbing pore observed on the cross sectional surface of yellow poplar wood. The sound absorption coefficients and air permeability of sapwood were higher than those of heartwood for Liriodendron tulipifera.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.4
• /
• pp.65-78
• /
• 1990

For the purpose of Improving the sounding boards for the conventional GAYAKUM, I was making approximately 202 specimens of radial board, 371 specimens of tangential board by cutting along the grain and the part of stem and 31 specimens of the disjointed traditional GAYAKUM made in Paulownia coreana. And it was conducted to measure specific gravity, dynamic Young's modulus, internal friction, resonant frequency, velosity of sound and width of annual ring by the method of the frexural vibration in a free-free bar in the audio frequency range. And it confirmed the juvenile wood by measuring wood fiber length of specimens. It was also conducted to investigate dynamic properties and moisture absorption by various heat-treatment and to test dynamic Young's modulus and internal friction for the disjointed conventional GAYAKUM. The results obtained were summarized as follow: 1. The Juvenile wood is located within about 7 annual rings from the pith in Paulownia coreana. 2. As increased with the specific gravity, the dynamic Young's modulus had more and more increased, but the internal friction had slightly decreased. 3. I think that radial board would be good for sounding board wood. because radial board is higher than tangential board in dynamic Young's mudulus and internal friction is lower than tangential board. 4. The value of mean dynamic Young's modulus on the conventional GAYAKUM, radial board and tangential board of 604 samples is $0.4283\pm0.037(\times10^{11}dyne/cm^2)$, $0.4316\pm(\times10^{11}dyne/cm^2)$ and $0.4234\pm0.112(\times10^{11}dyne/cm^2)$ respectively. The value of the radial board showed little higher than that of conventional GAYAKUM, but It had a similar tendency between conventional GAYAKUM and tangential board. 5. The annual ring width by four aspect is more narrow in north and west than that of others. 6. The values of specific gravity and dynamic Young's modulus in the mature wood showed higher than those of juvenile wood. 7. As the grain angle in the butt wood more increased to bark from pith, the dynamic Young's modulus were low. Then it was not good for sounding board. 8. It appeared that the heat-treatment for sounding board wood had a more effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature. 9. As increased with the temperature, the rate of moisture absorption of heat-treatment wood had decreased. In conclusion, I thought that the sounding board wood for GAYAKUM would had the most effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature using the radial board of mature wood.

• Journal of the Korea Furniture Society
• /
• v.18 no.4
• /
• pp.275-281
• /
• 2007

This study was carried out to know bending process property of bentwood by treatment methods such as microwave and ammonia solution treatment. Bentwood processing was operated on bending-jig form with 60mm and 100mm radius of curvature (ROC). The species was used to Korean red pine (Pinus densiflora). No significant difference was shown in bentwood processing method on ROC. In treatment method, ammonia solution treatment for bentwood was better in dimensional stability and working ability than that of microwave treatment. However, bentwood stress was reduced with ammonia solution treatment. Color of bentwood surface appearance has a dark tendency in ammonia solution treatment. But it seems to beautiful effect of apparent annual ring is rising esthetically by ammonia solution treatment. To utilize wood as a exterior material for living amenity, it has to be closely examined from various angles including surface property, degree of swelling and shrinkage, drying state, retaining strength, durability, safety, and insect damage.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.2
• /
• pp.101-111
• /
• 2014

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaining (BR) and bark-remaining-coating (BRC) treatments on the air circulating oven-drying characteristics of Japanese larch hollowed round-post was evaluated. The drying times of the hollowed round-posts for control, VD, HCO and BR specimens were 72, 168, 204 and 240 hours, respectively, from the initial MC to about 8% MC, which was recommended as the indoor in-use MC. The temperature in the hole of the VD specimen was lower than that of wood and the difference between air temperature in the hole and wood temperature became large during drying period. The vapor pressure of air in the hole was higher than that of inside wood for all specimens except VD specimen. The surface checks on all specimens were observed in increasing order of BR, BRC, UC, HCO and VD specimens.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.52-60
• /
• 2006

This study investigated how wood properties (i.e., annual rings, sapwood, heartwood, and cracks) might affect preservative treatment in Japanese larch (Larix leptolepis) round-wood product. We specially focused on small-diameter (~10 cm diameter) wood that is commercially sold in market. Among 100 wood samples, the groups of sample with 13~16, 17~20 annual rings represented 33 and 27 in each frequency, while 2~3 and 4~5 mm annual ring width accounted for 72 and 68 in frequency. More than a half (54%) of wood samples contained a mix of heartwood and sapwood in its surface. The rest (46%) had only heartwood exposed in the wood surface. A wide range of checks were showed in the wood samples, but the highest frequency was observed in samples with 1~6 surface (1~14 mm in size) checks and 1~4 end-grain (8~14 mm in size) checks in each round-wood sample. Pressure treatment resulted in a wide range of penetration of ACQ (Alkaline Copper Quat) into the wood, showing $4.3{\pm}4.19mm$ penetration in the wood samples contained a mix of heartwood and sapwood in its surface. However preservative treatment was much less effective for the heartwood only wood samples, ranging average 1.3 mm with ACQ and 1.1 mm with CCA (Chromated Copper Arsenate). These penetration results shown in heartwood samples did not meet the penetration standard that is required for H3 by the Korean Forest Service in relation to wood preservation treatment. These low penetration results were not significantly improved even if we incised wood samples to improve treatment effect, showing only small increase of 0.7 mm with ACQ and 0.6 mm with CCA. When preservative treatment was tested with heartwood, penetration of preservatives decrease with increase of annual rings per a cross-section area (r=0.5345). We also found that the length and number of check had no effect on preservative treatment, showing r=0.1301 and r=0.1802, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.677-684
• /
• 2016

This study was carried out to confirm the effects of the knife-incising and longitudinal kerfing treatment on high-temperature drying characteristics of red pine square timber with dimensions of thickness 15 cm. The range of final moisture content was investigated 5.6% to 7.5% after drying. The differences did not exist in the moisture content and distribution according to the pretreatment condition. In the case of longitudinal kerfing treatment, the surface check occurrence was reduced than the control. In addition, the twist had a tendency to decrease due to the longitudinal kerfing treatment. The knife-incising and longitudinal kerfing treatment were investigated to be ineffective on internal checks and drying shrinkage.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.302-314
• /
• 2016

This study was carried out to confirm the effects of the knife-incising and kerfing pretreatment on the moisture content and surface check occurrence of Douglas-fir heavy timber. In the case of moisture content, the moisture gradient that formed in the inner part of the specimen was observed in all specimens. In addition, the moisture gradient was formed differently from the surface layer to 72 mm depending on the pretreatment conditions, and it was formed gradually in the kerfing than the knife-incising. In addition, it was found that the solid volume should be considered when measuring the average moisture content. In the case of surface check, the surface check occurrence was reduced in the knife-incising, kerfing, and the combination of knife-incising and kerfing than the control. In particular, the kerfing treatment was shown that the expansion of surface check width was effectively suppressed. In the case of knife-incising treatment, although the surface check was less than the control, the preventive effect on the surface check occurrence did not reach the level of the kerfing treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.31-38
• /
• 1999

This paper deals with a coating technique of hardening surface layer of softwood{Larix leptolepis) flooring board to improve its surface properties such as hardness and abrasion resisitance without spoiling its exellent qualities such as beautiful color tones and great strength. For surface hardening of the wood, polyurethane wood sealer was used as under coat, polyurethane sanding sealer as intermediate coat, and UV-curing epoxy acrylate and urethane acrylate varnishes as top coat. The hardness of the wood was improved by the coating treatment and it was similar to that of high density hardwood such as oak, keruing. The abrasion resistance of the coated wood was greatly improved by UV curing epoxy acrylate or urethane acrylate varnishes. Adhesion properties and impact resisitance of the coated wood surface were also good. It was suggested that the well-coated larch wood could be used as interior flooring board as substitute for hardwood such as keruing.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.488-502
• /
• 2020

In this study, the moisture absorption and desorption properties presented by the Health-Friendly Housing Construction Standards of South Korea were compared using the wood of three tree species (Douglas-fir, Hinoki, Larch) and two types of wood-based materials(Plywood, WML Board^Ⓡ). The national standards for functional building materials present that the amounts of moisture absorption and desorption should be at least 65g/㎡ on average, respectively according to the test method under KS F 2611:2009. Therefore, in this study, the moisture absorption/desorption properties of materials with no treatment (Control), with punching, and with surface stain finishing and the moisture absorption/desorption property improvement effects of the treatments were compared and analyzed. According to the results of this study, it was evaluated that all five types of wood and wood-based materials tested did not satisfy the amount of moisture absorption/desorption of at least 65g/㎡, which is the performance standard for moisture absorption/desorption functional building materials, indicating that untreated wood and wood-based materials cannot be applied as functional finishing materials according to the Health-Friendly Housing Construction Standards. The surface stain finishing greatly reduced the moisture absorption and desorption rates of the materials, and the amounts of moisture absorbed and desorbed were also shown to decrease by at least two times on average. When the surfaces of the materials were punched with Ø4mm holes at intervals of 20 mm, the moisture absorption/desorption areas increased from 18% to 51%, and this increase was shown to be capable of increasing the amounts of moisture absorbed/desorbed by 29% on average at the minimum, and 81% on average at the maximum. The effects of punching were shown to be identical even in cases where the materials were stain finished. For the application of wood or wood-based materials as eco-friendly, health-friendly, and moisture absorption/desorption functional building materials hereafter, it is judged that new physical and chemical improvement studies should be conducted, and treatment methods should be developed.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.2
• /
• pp.61-70
• /
• 2012

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaing (BR) and bark-remaining- coating (BRC) treatments were evaluated during air circulating oven-drying of hollowed round-post of Korean red pine. Hollowed round-post could be dried from the green condition to approximately 6% MC within 84 to 156 hours for the UC, HCO and VD specimens and it took 72 to 240 hours to about 8% MC, which is recommended as the indoor in-use MC. The temperatures in the hole of the Control (UC) and HCO specimens constantly showed a higher-leveled distribution pattern than those inside wood. The vapor pressure in the hole of the UC, HCO and BR specimens was higher than that inside wood and showed difference as highest value of about 20 mbar. The surface checks of all specimens were mild and were observed in increasing order of BRC, BR, UC, VD and HCO specimens.