• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.13-44
• /
• 1982

1. Since long time ago, it has been talked about that soaking wood into water for a long time would be profitable for the decreasing of defects such as checking, cupping and bow due to the undue-shrinking and swelling. There are, however, no any actual data providing this fact definitly, although there are some guesses that water soluble extractives might effect on this problem. On the other hand, this is a few work which has been done about the effect of water soluble extractives upon the some physical properties of wood and that it might be related to the above mentioned problem. If man does account for that whether soaking wood into water for a long time would be profitable for the decreasing of defects due to the undue-shrinking and swelling in comparison with unsoaking wood or not, it may bring a great contribution on the reasonable uses of wood. To account for the effect of water soluble extractives upon physical properties of wood, this study has been made at the wood technology laboratory, School of Forestry, Yale university, under competent guidance of Dr. F. F. Wangaard, with the following three different species which had been provided at the same laboratory. 1. Pinus strobus 2. Quercus borealis 3. Hymenaea courbaril 2. The physical properties investigated in this study are as follows. a. Equilibrium moisture content at different relative humidity conditions. b. Shrinkage value from gre condition to different relative humidity conditions and oven dry condition. c. Swelling value from oven dry condition to different relative humidity conditions. d. Specific gravity 3. In order to investigate the effect of water soluble extractives upon physical properties of wood, the experiment has been carried out with two differently treated specimens, that is, one has been treated into water and the other into sugar solution, and with controlled specimens. 4. The quantity of water soluble extractives of each species and the group of chemical compounds in the extracted liquid from each species have shown in Table 36. Between species, there is some difference in quantity of extractives and group of chemical compounds. 5. In the case of equilibrium moisture contents at different relative humidity condition, (a) Except the desorption case at 80% R. H. C. (Relative Humidity Condition), there is a definite line between untreated specimens and treated specimens that is, untreated specimens hold water more than treated specimens at the same R.H.C. (b) The specimens treated into sugar solution have shown almost the same tendency in results compared with the untreated specimens. (c) Between species, there is no any definite relation in equilibrium moisture content each other, however E. M. C. in heartwood of pine is lesser than in sapwood. This might cause from the difference of wood anatomical structure. 6. In the case of shrinkage, (a) The shrinkage value of the treated specimen into water is more than that of the untreated specimens, except anyone case of heartwood of pine at 80% R. H. C. (b) The shrinkage value of treated specimens in the sugar solution is less than that of the others and has almost the same tendency to the untreated specimens. It would mean that the penetration of some sugar into the wood can decrease the shrinkage value of wood. (c) Between species, the shrinkage value of heartwood of pine is less than sapwood of the same, shrinkage value of oak is the largest, Hymenaea is lesser than oak and more than pine. (d) Directional difference of shrinkage value through all species can also see as other all kind of species previously tested. (e) There is a definite relation in between the difference of shrinkage value of treated and untreated specimens and amount of extractives, that is, increasing extractives gives increasing the difference of shrinkage value between treated and untreated specimens. 7. In the case of swelling, (a) The swelling value of treated specimens is greater than that of the untreated specimens through all cases. (b) In comparison with the tangential direction and radial direction, the swelling value of tangential direction is larger than that of radial direction in the same species. (c) Between species, the largest one in swelling values is oak and the smallest pine heartwood, there are also a tendency that species which shrink more swell also more and, on the contrary, species which shrink lesser swell also lesser than the others. 8. In the case of specific gravity, (a) The specific gravity of the treated specimens is larger than that of untreated specimens. This reversed value between treated and untreated specimens has been resulted from the volume of specimen of oven dry condition. (b) Between species, there are differences, that is, the specific gravity of Hymenaea is the largest one and the sapwood of pine is the smallest. 9. Through this investigation, it has been concluded that soaking wood into plain water before use without any special consideration may bring more hastful results than unsoaking for use of wood. However soaking wood into the some specially provided solutions such as salt water or inorganic matter may be dissolved in it, can be profitable for the decreasing shrinkage and swelling, checking, shaking and bow etc. if soaking wood into plain water might bring the decreasing defects, it might come from even shrinking and swelling through all dimension.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.6
• /
• pp.505-516
• /
• 2009

The effects of wood species, particle size of wood flours and coupling treatment on the mechanical properties of wood plastic composites (WPC) are investigated in this study. Chemical components of wood flour from 3 different wood species were analyzed by the chemical analysis. Wood flours of 40~60 mesh and 80~100 mesh were manufactured from Larix (Larix kaempferi Lamb.), Quercus (Quercus accutisima Carr.), and Maackia (Maackia amuresis Rupr. et Maxim). The wood flours were reinforced into polypropylene (PP) by melt compounding and injection molding, then tensile, flexural, and impact strength properties were analyzed. The order of alpha-cellulose content in wood is Quercus (43.6%), Maackia (41.3%) and Larix (36.2%). The order of lignin content in wood is Larix (31.6%), Maackia (24.7%), and Quercus accutisima (24.4%). The content of extractives in wood is in the order of Larix (8.5%), Maackia (4.4%), and Quercus accutisima (3.9%). As the content of alpha-cellulose increases and the lignin and extractives decreases, tensile and flexural strengths of the WPC increase. At the same loading level of wood flours, the smaller particle size (80~100 mesh) of wood flours showed highly improved tensile and flexural strengths, compared to the larger one (40~60 mesh). The impact strength of the WPC was not significantly affected by the wood species, but the wood flours of larger particle size showed better impact strengths. The addition of maleated polypropylene (MAPP) provided the highly improved tensile, flexural and impact strengths. Morphological analysis shows improved interfacial bonding with MAPP treatment for the composites.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.73-80
• /
• 2015

Corn stalk is the lignocellulosic biomass, which remain as leftover after harvesting. To use the corn stalk as raw material for paper industry, soda pulping was applied. In chemical compositional analysis, extractive contents of corn stalk (45.1%) was higher than hardwood. With corn stalk pith, soda pulp yield was 25.3% at 10.6 Kappa number, but 39.5% yield with 14.8 Kappa number for corn stalk rind. Higher extractives content in pith is one of the reason for lower pulp yield than rind. Pith pulp fibers had higher fines content than rind pulp. Pith parenchyma cell was removed as fines during pulping or washing process, which caused the lower yield. To use the corn stalks as a raw material for paper making, de-pith process is essential for higher pulp yield and longer pulp length.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.1
• /
• pp.80-89
• /
• 2019

Pine barks are important biomass resources because they are utilised in the production of pine wood and rosins. However, no chemical study has been conducted on the hydrophilic status of pine barks in Indonesia. This aim of this study is to explore the hydrophilic extracts of the barks from six Pinus species (P. elliotii, P. caribeae, P. oocarpa, P. merkusii P. montezumae, and P. insularis). The hydrophilics of pine barks were analysed using gas chromatography-mass spectrometry. The presence of polyphenol contents in the ethanol extracts obtained from the barks of six Pinus species was determined using the tannin-formaldehyde method, Folin-Cioucalteu assay, and vanillin-HCl assay. The ethanol and hot water soluble extractives derived from inner barks were higher in quantity when compared to those derived from the outer bark samples. The polyphenol measurement showed that the highest value of total phenol content was derived from the outer bark of P. montezumae whereas those of the total phenol and tannin- formaldehyde contents were derived from the inner and outer barks of P. oocarpa. GC-MS analysis revealed that nitrogenous compounds are dominant constituents in the inner and outer barks of the six species, followed by sugars and monophenolics, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.95-100
• /
• 2006

This study is to isolate bio-active compounds from Alnus firma and evaluate their antioxidant activity. Dried wood powder of A. firma was extracted by organic solvents and fractionated in the sequential extraction steps. The isolated compounds were characterized by EI-MS, $^{13}C-$ and $^1H-NMR$ including COSY, DEFT, HMQC, and HMBC. Antioxidant activities of the isolated compounds were evaluated by DPPH (1,1-diphenyl-2-picrylhydrazyl) free radical scavenging effect. From the wood of A. firma, three kinds of diarylheptanoids, alnusodiol (1), alnusonol (2) and alnusone (3), and gallic acid (4) were isolated. Among these four compounds, compound 1, 2, and 3 are isolated from A. firma for the first time. The antioxidant activity of gallic acid was 93.5% at the concentration of 100 ppm. This compound showed stronger antioxidant activity than those of other isolated compounds and the reference BHT (butylated hydroxytoluene).

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.15-22
• /
• 1997

The effectiveness of presteaming for improving CCA treatability on refractory Japanese larch heartwood was investigated in this study. Presteaming was effective on improving treatability, and the extent of improvement was dependent on moisture contents of wood specimen and steaming conditions. Green wood showed higher average value in both preservative retention and penetration than dry wood, and steaming under pressure conditions also had higher treatability than steaming at atmospheric conditions. The degree of improvement for treatability was increased with the extension of steaming period. Treatability of dry wood pres teamed under pressure conditions more than 6 hours and green wood for 3 hours was similar to that enhanced by conventional incising. Presteaming green wood under pressure conditions more than 6 hours was more effective than conventional incising in improvement of CCA treatability, and resultant treatability satisfied a minimum value required for CCA-treated wood for being used at the regions of hazard class H3 and H4. In addition, an improvement of treatability by presteaming was due to an increase in permeability resulted from the degradation of hemicelluloses within aspirated pit membrane and cell wall, not the removal of extractives from pit membrane. The reduction in strength, measured as longitudinal compressive strength, due to pres teaming was related with the degradation of hemicelluloses, and was increased as steaming conditions were severe. The degree of strength reduction associated with presteaming treatment to obtain required treatability could be quantified from the relatively good relation between the increase in treatability and the decrease in strength.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.4
• /
• pp.571-588
• /
• 2016

Eucalyptus pellita F. Muell is one of pulp woods that is being developed through breeding plantation programs in Indonesia. The research aimed at exploring the chemical and morphological characteristics of fiber, and to determine the rank of plus trees from 4 provenances based on the suitability for pulps. The materials included the plus trees of E. pellita (9 years) from the 2nd generation of progeny tests in Pelaihari, South Borneo. Wood properties under investigation included the chemical properties and morphological fiber characteristics (fiber dimensions and its derived properties). In the present study, data were analyzed using descriptive statistic, Analytic Hierarchy Process (AHP) and Pearson's correlation. Results showed that the chemical properties of E. pellita, i.e. the contents of ethanol-toluene extractives, hot water soluble extractives, holocellulose, alphacelullose, and lignin were $3.08{\pm}1.00%$, $1.41{\pm}0.38%$, $75.26{\pm}2.58%$, $49.02{\pm}2.88%$, and $29.49{\pm}1.86%$, respectively. The average values of wood fiber morphology were $1.02{\pm}0.08$ mm (fiber length), $13.25{\pm}1.64{\mu}m$ (fiber diameter), of $6.94{\pm}1.70{\mu}m$ (lumen diameter), $3.15{\pm}0.52{\mu}m$ (fiber wall thickness), $0.97{\pm}0.30$ (Runkel ratio), $0.57{\pm}0.10$ (Luce's shape factor), $78.21{\pm}10.34$ (slenderness ratio) and $130.91{\pm}33.77{\times}10^3{\mu}m^3$ (solids factor). The AHP scoring rank indicated that the best individuals were 28.4.3.28 (Kiriwo Utara), 12.1.5.28 (North Kiriwo), 19.11.5.45 (Serisa Village), 3.8.4.9 (South Kiriwo), and 6.6.3.15 (South Kiriwo). Pearson correlation analysis showed significant correlations between the levels of fiber length with alpha-cellulose content (r = 0.39) as well as the fiber length with ethanol-toluene extractive contents (r = -0.41).

• Journal of Korean Society of Forest Science
• /
• v.71 no.1
• /
• pp.59-65
• /
• 1985

In this study, the vegetation of Pinus densiflora S. et Z., Pinus regida Miller, Pinus koraiensis S. et Z., and Larix kaempferi Satgent (major conifers) stands planted in the Chungcheong-province was investigated to obtain the fundamental informations for the improvement of coniferous barks utilization. The results may be summarized as follows; 1) Barks are much richer in quantity of extractives and lignin than the corresponding wood. Alcohol-benzene extractives of Pinus koraiensis barks are the highest among others. Pentosan contents are lower in the bark than in the wood, but pentosan contents of the Larix kaempferi bark is the highest among others. 2) Barks are acid in nature, and PH values of barks varying from 3.5 to 4.1 are lower than that of wood. The ash contents of barks are greater than the corresponding wood. 3) A bark comprises from 13.9 to 19.8 percents of a typical log by volume. The calorific values are higher in the barks than in the wood, and calorific values of Pinus koraiensis barks are the highest among others.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.2
• /
• pp.447-450
• /
• 2004

Overall migration through epoxy layer coated wood was investigated to estimate the coating thickness satisfying the regulatory limit. As an index of overall migration, KMnO$_4$ oxidizable extractives by the food simulant water solution was used. Migration pattern in interest range could described by a simple diffusion model and the temperature dependence of the permeability index could be explained by Arrhenius equation. The thickness of epoxy coating greater than 0.004 mm was analyzed to be required for satisfying the regulatory guideline.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.4
• /
• pp.59-63
• /
• 1987

As the production of chestnuts from chestnut trees has been increased annually in the past several years in this country, developing the utilities of chestnut bur has been considered as one of main research problems. Therefore. in this paper, the chemical components were analysed to find a way of utilizing the chestnut bur. It was proved that chestnut bur is abundant in extractives (hot water 16.0%, 1%-NaOH 40.6%) and tannin content (16.5%). Of the tannin, the soluble tannin (3.2%) content is higher than condensed tannin (2.2%), and gallic acid content(3.3-3.9%) is slightly higher than ellagic acid(2.8-3.0%), For more effectively utilizing as a tannin resources, the chestnut bur should be collected immediately after yield of chestnuts, maybe in October every year.