• Journal of the Korean Applied Science and Technology
• /
• v.33 no.1
• /
• pp.75-82
• /
• 2016

The technology of fast pyrolysis is regarded as a promising route to convert lignocellulose biomass into bio-oil which can be upgraded to transportable fuels and high quality chemical products. Despite these promises, commercialization of bio-oil for fuels and chemicals production is limited due to its notoriously undesirable characteristics, such as high and changing viscosity, high water and oxygen contents, low heating value and high acidity. Therefore, in this study quality improvement of bio-oil through vaccum distillation had been targeted. A 600 g of cork oak(Quercus variabilis) which grounded 0.8~1.4 mm was processed into bio-oil via fast pyrolysis for 1.64 seconds at $465^{\circ}C$ and temperature of vaccum distillation(100hPa) was designed to control, $40^{\circ}C$, 50, 60, 70, and 80 for 30min. Bio-oil, biochar, and gas of pyrolytic product were produced to 62.6, 18.0 and 19.3 wt%, respectively. The water content, viscosity, HHV(Higher Heating Value) and pH of bio-oil were measured to 0.9~26.1 wt%, 4.2~11.0 cSt 3,893~5,230 kcal/kg and 2.6~3.0, respectively. Despite these quality improvement, production was still limited due to its notoriously undesirable characteristics, therefore continous quality improvement will be needed in order to use practical fuel of bio-oil.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.5 no.1
• /
• pp.21-24
• /
• 1999

The analysis of hazard compounds, including naphthalene, biphenyls (BP) and diethyl phthalate (DEP), was conducted from the wooden kitchenwares and sanitory produce. Fifty samples of that wooden products in the local market were purchased for the study. All the samples were extracted by benzene and n-heptane, followed by the analysis through GC-MSD. As a result, neither naphthalene nor diethyl phthalate were found, however, trace amount of biphenyls were detected on all the samples ranged from 0.1 to 3.1 ppm. Biphenyls also contained both in the imported and the domestic of White Birch wood, as 0.25 ppm and 0.34 ppm, respectively. The concentration of biphenyls reduced with the process of the original woods, and especially the detection range was relatively low compared with the permission one of apples (110 ppm). The results suggested that biphenyls were contaminated into the product not by the addition doting the process of manufacture, but as the component itself in raw wood materials. Also, the content of the residual biphenyls were not suspected to give the harmful effects.

• Journal of Adhesion and Interface
• /
• v.21 no.4
• /
• pp.135-142
• /
• 2020

Recently, people's interest in eco-friendly plastics derived from nature to replace petroleum-based plastics is increasing due to environmental problems such as microplastics. In line with this trend, eco-friendly adhesives using natural materials and processes are also being developed in the adhesive field. Among them, maltose is a natural substance derived from starch and is the main component of starch syrup used as a food additive. Due to its lower molecular weight than starch, it is easily soluble in water, and above all, there is a possibility that it can be copolymerized with other monomers through solution polymerization. However, researches related to the application of maltose to adhesives are very rare. In this study, after modifying maltose using acrylic anhydride, the product was analyzed through FT-IR and H-NMR. And the modified maltose was copolymerized with two kinds of acrylic monomers. The synthesized adhesive was applied on the wood and the adhesive performance were investigated.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.1
• /
• pp.72-78
• /
• 2002

Cultivation of Pholiota adiposa on sawdust media and its mixed substrates with various agricultural by-products was attempted. The composition of each substrates were compared from the viewpoint of cultivation possibilities with the production of Pholiota adiposa. Populus deltoides showed the best production of the mushroom with 795 g, followed by Robinia pseudo-acacia and Quercus acutissima. The mixed sawdust media with 70% of Robinia pseudo-acacia and 30% of Populus deltoides showed the best production of the mushroom with 265 g followed by the mixture of Robinia pseudo-acacia and Populus deltoides with 50% each with 228 g, while the addition of Quercus acutissima showed the negative effect for the production of Pholiota adiposa. Thus, Robinia pseudo-acacia was considered to be an effective amendment for the production of the mushroom. In addition, various kinds of agricultural by-products showed additive effect for the production of the mushroom, too. Therefore, we could concluded that the sawdust of Robinia pseudo-acacia and agricultural by-products can be used to cultivate Pholiota adiposa.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.2
• /
• pp.20-25
• /
• 1989

This study was carried out in order to investigate the treatment effect of PEG soln which is a common dimensional stabilizer to green log. sawing panel etc, on bonding product including plywood widely-used in secondary processing unit. The 30% concentration of aqueous PEG soln. with molecular weight of 400, 1.000 and 4,000 were prepared respectively, and also dipping the veneer in the PEG soln. spreading the PEG soln. on veneer and mixing the PEG soln. in the adhesive were allowed. Then the ratio of PEG impregnation on veneer, the adhesive strength of plywood were epitomized as follows: The ratio of impregnation by PEG 4,000 at dipping condition was highest. while that by PEG 400 at same condition was lowest. However, the effect of PEG molecular weight on the ratio of impregnation at spreading condition did not occur. 2. The adhesive strength was great in the order of 4,000>400>1,000 in molecular weight of PEG at dipping and spreading conditions. In case of mixing the PEG soln. in the adhesive, the adhesive strength was great in the order of 400>1,000>4,000 in molecular weight of PEG. Throughout three treatment conditions, PEG 400 was relatively favourable with about 10kg/$cm^2$ dry strength. 3. The adhesive strength was great 10 the order of spreading >dipping >mixing condition. 4. Although adhesive strength with the 30% concentration of aqueous PEG soln. was decreased by 35% and over, compared to control (non-treatment) adhesive strength, all types of PEG treatment except mixing the PEG soln. in the adhesive exceeded the standard dry strength for common use panel. 7.5kg/$cm^2$. 5. In warm water-proof test, the adhesive strengths by all PEG treatment conditions were less than the standard wet strength, 7.5kg cot, and also delamination of glue line occured mostly in mixing in the PEG soln. in the adhesive condition.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.90-95
• /
• 2004

Pitch pine (Pinus rigida) has been planted in Korean forests for several decades, primarily for erosion control and use as a fuel supply. To enhance its value, and especially potential use as lamina for structural glued laminated timber (glulam), log quality and lumber yield of pitch pine were evaluated in this study. Trees from pure pitch pine stands with an average diameter at breast height of 32 cm were felled and bucked into 3.6m long 15 cm minimum butt-end diameter logs. Over 80% of the logs were classified to No.2 or No.3 visual grade group. Upon sawing total lumber yield was 55.2%, 39.9% for structural glulam lamina, 7.2% for louver, and 8.1% for miscellaneous use. The final lumber yield for manufacturing structural glulam, after cross-cutting to eliminate knots and finger jointing, was only 15.3%. To enhance this manufacturing yield requires that the rate of knot-included lumber used as lamina be raised. However arrangement of the knot-included lamina, whose mechanical properties need to be accurately evaluated, must be optimized to minimize any reduction to the structural glulam strength. The log quality and lumber yield of pitch pine evaluated in this study are expected to facilitate proper planning for wood product manufacture in the Korean lumbering and glulam industrial field, which has not previously dealt with this species.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.82-89
• /
• 2004

Two kinds of chemicals (RNF-3 and RNF-4) with high anti-mold effectiveness against stored fungi causing fungal discoloration was selected from among the six kinds of fluoride-based chemicals in the preceding study. In this study, the anti-mold test using 16 species fungi isolated from the softwood lumbers which were fungal discolored and field test in the sawmill was carried out to prove the feasibility for practical using of selected chemicals.For the isolated fungi, the RNF-3 consist of F and Cu showed high mycelial growth control in the PDA medium and fungicidal effectiveness in the japanese red pine (Pinus densiflora), korean pine (Pinus koraiensis) and radiata pine (Pinus radiata) when the concentration was 2% or more. However the RNF-4 consist of F only was not effective compared with RNF-3 because of mycelial growth in the PDA medium and wood treated with 2% or more chemical solution. The RNF-3 also showed a strong anti-mold effectiveness because there was no fungal discoloration for the radiata pine boards treated by 2% and 10 min. soaking in the field test. These results mean that RNF-3 can be used as domestic anti-stain chemicals for prevention of fungal discoloration of the softwood lumber

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.6
• /
• pp.561-567
• /
• 2010

In this study, we evaluated optimal conditions for ethanol production of the spruce hydrolysate (SH) obtained from diethyl oxalate pretreatment. Fermentable sugar concentration in SH was 29.04 g/${\ell}$ except arabinose. Monosaccharides obtained from the oligomer degradation were mainly mannose (39.26 g/${\ell}$) and galactose (12.83 g/${\ell}$). Concentration of 5-HMF and furfural which are inhibitors on ethanol fermentation were 0.09 g/${\ell}$ and 0.04 g/${\ell}$ respectively. Concentration of acetic acid and total phenolic compounds in SH were 1.4 g/${\ell}$ and 2.83 g/${\ell}$. Ethanol production using hydrolysate was 11.7 g/${\ell}$ at optimal pH 6.0 after 48 h. Specific ethanol production was 0.15 (g/(${\ell}^*h$)) at pH 5.0 and 5.5. while that was 0.24 (g/(${\ell}^*h$)) at pH 6.0. Specific ethanol production has difference depend on initial pH for fermentation. Ethanol production was 14.3 g/${\ell}$ after 48 h when xylanase 20 IU was added in SH for degradation of oligomer during fermentation. It implied that ethanol production increased by 22.2% compare with control (without xylanase).

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.59-63
• /
• 2008

A theoretical model was developed to describe the flow behavior of a filled polymer in the packing stage of reaction injection molding and predict the residual stress distribution of thin injection-molded parts. The model predictions were compared with experiments performed for phenol-formaldehyde resin filled with wood dust and cured by urotropine. The packing stage of reaction injection molding process presents a typical example of complex non-isothermal flow combined with chemical reaction. It is shown that the time evolution of pressure distribution along the mold cavity that determines the residual stress in the final product can be described by a single 1D partial differential equation (PDE) if the rheological behavior of reacting liquid is simplistically described by the power-law approach with some approximations made for describing cure reaction and non-isothermality. In the formulation, the dimensionless time variable is defined in such a way that it includes all necessary information on the cure reaction history. Employing the routine separation of variables made possible to obtain the analytical solution for the nonlinear PDE under specific initial condition. It is shown that direct numerical solution of the PDE exactly coincides with the analytical solution. With the use of the power-law approximation that describes highly shear thinning behavior, the theoretical calculations significantly deviate from the experimental data. Bearing in mind that in the packing stage the flow is extremely slow, we employed in our theory the Newtonian law for flow of reacting liquid and described well enough the experimental data on evolution of pressure.

• Archives of design research
• /
• v.18 no.2 s.60
• /
• pp.303-314
• /
• 2005

This study is intended to promote local woodcraft industry with revitalization of local festival in Inje-county. To do so, we propose the travel souvenir design with local identity and the plan for production and marketing based on the management of 'Design Hospital' and the building of production method through 'laser wood inlaying technique like puzzle style'. Research method is benchmarking analysis of successful cases of travel souvenir which is developed for cultural contents of local festival. The result of this study is the following. First, design outsourcing is done one of support in industry focused on old boy network, Through it, Special brain of design can be supplied without compensation. Also the difficulty of manpower problem is lessened and the ability of product development in short term can be guaranteed. On the basis of this, we are able to apply Mass Customization production by up to date digital production method. This enables us to maintain the production flexibility of cultural goods fit for the traits of local festival. This study is intended to present the best model guananteeing both profit of wood technological industry and the possibility of local cultural.