• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.10
• /
• pp.445-451
• /
• 1986

The speed control system of induction motor without speed sensor is proposed in this paper. The speed of induction motor is calculated by motor terminal voltages and currents. The equations for speed calculation are derived and they are implemented on 16bit micro-processor Mc68000. The software and hardware for the Mc 68000 is developed. To prove the validity of the proposed method, the calculated speed is compared with the measured speed. The maximum speed error is nearly 1% in the overall range. The proposed speed calculation method is applied to the Current Source Inverter(CSI) fed induction motor drive system. The experimental results show the good dynamics and the resonable speed control accuracy.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.8
• /
• pp.426-430
• /
• 1999

In this paper, a speed sensorless algorithm for a high-speed induction motor is proposed. The proposed algorithm simply estimates rotor speed by integrating the deviation between the command current value of a controller and the real current value of the motor. To estimate rotor speed without a speed sensor, a fuzzy speed controller and a neural network speed estimator are applied. Computer simulation and implementation of the proposed system is described.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.43-52
• /
• 1997

Ultrasonic sensors are widely employed in detecting range to a target by the virtue of their low cost and simplicity. However, the sensor's measurements are corrupted by systematic errors due mainly to the dependency of sound speed upon surrounding conditions and random errors of uncertain origin. In this paper, we present the results of research carried out to reduce these errors for increasing the reliability of an untrasonic sensor system to be used in orbotic or other automated system's range finding. The sensor system designed herein is in a peuliar structure having a reference target and two receivers. Echoes from a small reference target placed at a known distance are used for compensating the variations of sound speed according to the changes of sensing conditions. Unlike existing ones, the technique proposed can compensate the effects of temperature or any other physical parameters without an additional sensor dedicated to the compensation. The measurements by two redundantly employed receivers are fused to reduce random errors in a statistical sense. The correlation of the signals from the receivers sharing a hardware in part is considered in the fusion process. The methodology desicribed in this paepr is conceptually simple, easy to be implemented, and effetive to increase the accuracy of the sensor measurements as experimental results confirm.

• Korean Journal of Optics and Photonics
• /
• v.10 no.4
• /
• pp.273-278
• /
• 1999

A TDM-multiplexed fiber optic pressure/temperature sensor system utilizing fiber optic Fabry-Perot interferometers as sensing devices was developed and applied to measure water level variations and temperature variations. The maximum measurement speed of the system without saving measurement data is 4500 times per second and the response time of the sensors is thought to be ~ms. The difference between the theoretical value and the measured value for the scale factor of water level sensor and temperature sensor was +13.7%, -18% respectively. The nonlinearity of the sensors after calibration was less than 1%. The sensor system was applied to verify the capability of measuring the temperature variations and water level variations at a high speed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.3
• /
• pp.111-115
• /
• 2012

Generally, brushless DC motor(BLDCM) driving system uses hall sensors or encoders as the mechanical position or speed sensor. It is necessary to achieve the informations of rotor position for driving trapezoidal type brushless DC motor without any position sensor. In this paper, the commutation signals are obtained without the motor neutral voltage, multistage analog filters, A/D converters, or the complex digital phase shift circuits which are indispensable in the conventional sensorless control algorithms. In the proposed method, in stead of detecting the zero crossing point of the nonexcited motor back electromagnetic force for the average motor terminal to neutral voltage, the commutation signal are extracted directly from the specific average line to line voltage with low-pass filter, adder and comparators circuit. In contrast to conventional methods, the neutral voltage is not need; therefore, the commutation signals are insensitive to the common mode noise. Moreover, the complex phase shift circuit can be eliminated. The effectiveness of the proposed method is verified through simulation results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.891-894
• /
• 2007

This study presents fault diagnosis of low speed bearing using support vector machine (SVM). The data used in the experiment was acquired using acoustic emission (AE) sensor and accelerometer. The aim of this study is to compare the performance of fault diagnosis based on AE signal and vibration signal with same load and speed. A low speed test rig was developed to simulate various defects with shaft speeds as low as 10 rpm under several loading conditions. In this study, component analysis was also performed to extract the feature and reduce the dimensionality of original data feature. Moreover, the classification for fault diagnosis was also conducted using original data feature without feature extraction. The result shows that extracted feature from AE sensor gave better performance in faults classification.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.4
• /
• pp.503-510
• /
• 2003

A new method of induction motor drive, which requires neither shaft encoder nor speed estimator, is presented. The proposed scheme is based on decreasing current gap between a numerical model and an actual motor. By supplying the identical instantaneous voltage to both model and motor in the direction of reducing the current difference. the rotor approaches to the model speed. that is. reference value. The indirect field orientation algorithm is employed for tracking the model currents. The performance of induction motor drives without speed sensor is generally characteristic of poorness at very low speed. However, in this system, it is possible to obtain good speed response in the extreme low speed range.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.7
• /
• pp.930-936
• /
• 2003

A new method of direct current motor drive, which requires neither shaft encoder nor speed estimator, is presented. The proposed scheme is based on decreasing current gap between a numerical model and an actual motor. By supplying the identical instantaneous voltage to both model and motor in the direction of reducing the current difference, the rotor approaches to the model speed, that is, reference value. The performance of direct current motor drives without speed sensor is generally poor at very low speed. However, in this system, it is possible to obtain good speed performance in the low speed range.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.11
• /
• pp.632-639
• /
• 1999

SRM(Switched Reluctance Motor) drives require the accurate position and speed information of the rotor. These informations are generally provided by a shaft encoder or resolver. High temperature, EMI, and dust may make detection performance deteriorate. Therefore, the elimination of the position and speed sensor is desirable. In this paper, a nonlinear adaptive observer using the MRAS(Model Reference Adaptive System) is proposed. The rotor speed and position are estimated by the adaptation law using the real and estimated currents. The stability of the adaptive observer is proved by Lyapunov stability theory. The proposed methods are implemented with TMS320C31 DSP. Experimental results prove that the observer has a good estimation performance of the rotor speed and position despite of the parameter variations and loads, and the speed control can be accomplished in the wide speed range.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.7
• /
• pp.385-392
• /
• 2003

A nonlinear speed controller for a separately excited DC motor (SEDCM) based on a newly developed adaptive backstepping approach is presented. To compensate parameter uncertainties and load torque disturbance, a nonlinear adaptive backstepping control law and adaptive law are derived systematically step by step through virtual control input and suitable Lyapunov function. Also, speed observer without using costly speed sensor is presented. Simulation results show that the proposed controller can observe real speed and track the reference speed signal generated by a reference model.