• 조명전기설비학회논문지
• /
• 제17권1호
• /
• pp.68-73
• /
• 2003

본 연구는 유도전동기 구동에 관측기 이론을 적용하고 자계 방향형 벡터제어에 기초하여 센서리스 벡터구동 시스템을 개발한 것이다. 속도추정은 지령전압과 전류센서에서 검출한 전류와 관측기에서 구한 2차 자속으로 행하는 새로운 방법을 나타내었다. 이 속도추정은 자속과 유도전동기 정수만으로 결정되므로 파라미터의 이득 조정이 필요 없고 연산이 간단하다. 도출한 벡터제어 이론에 기초하여 유도전동기 구동을 위한 센서리스 속도제어 시스템을 설계 제작하였다. 그리고 시뮬레이션을 통해서 각 제어기의 이득정수와 관측기 이득을 결정하고 센서리스 벡터구동의 실험을 실현하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.466-469
• /
• 2001

In this paper, closed loop V/f control of induction motor has been implemented by the estimated speed. Closed loop V/f control improve the performance of induction motor drive system at low speed compared to open loop V/f control. However, closed loop V/f control need speed sensor. By using the estimated speed, closed loop V/f control is possible without speed sensor. Rotor speed is calculated from the difference between synchronous frequency and slip angular frequency. 3-phase voltage reference is obtained from synchronous frequency. And the PWM technique using space vector PWM is applied in this scheme. In the space vector PWM, effective time of 3-phase voltage reference is used to simplify the calculation of effective voltage time. This scheme is simple to implement and one chip microprocessor was used in experimental system.

• 한국정밀공학회지
• /
• 제19권10호
• /
• pp.107-113
• /
• 2002

To monitor the torque of an induction motor using current, rotating speed has been measured and used to calculate the slip angular velocity. Additional sensor, however, can cause extra expense and trouble. In this paper, a new algorithm is proposed to monitor the torque of vector controlled induction motor without any speed measuring sensor. Only stator current is measured to estimate the magnetizing current which is used to calculate flux linkage, rotor velocity and motor torque. Graphical programming is used to implement the suggested algorithm and to monitor the torque of an induction motor in real time. To solve the fluctuation problem of estimated torque caused from instantly varying rotating speed of an induction motor, the rotating speed is reconstructed based on the measured current signals. From several experiments, the proposed method shows a good estimation of the motor torque under the normal rotational speed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2739-2741
• /
• 1999

The rotor position information is needed to control the speed of SRM(Switched Reluctance Motor). The information of the rotor position have been generally acquired by using the encoder or the resolver. Speed sensors, however, occasionally malfunction under the hostile environment such as EMI, dust, high temperature and humidity, etc. There have been many efforts to drive the motor without speed sensors. In this paper, the EKF(Extanded Kalman Filter) theory is proposed to drive the SRM without speed sensors. Proposed method keeps a robust speed estimation performance against the input noise because it includes a noise model of measuring noise within the system. The validity of the proposed method has been examined by simulations.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.60-63
• /
• 1997

A new approach to the position sensor elimination of PM synchronous motor drives is presented in this study. Using the position sensing characteristics of PMSM itself, the actual rotor position as well as the machine speed can be estimated by adaptive flux observer and used as the feedback signal for the vector controlled PMSM drive. The adaptive speed estimation is achieved by model reference adaptive technique. The adaptive laws are derived by the Popov's hyperstability theory and the positivity concept. In order to verify the effectiveness of the proposed scheme, computer simulations are carried out for the actual parameters of a PM synchronous motor and the results well demonstrate that the proposed scheme provides a good estimation value of the rotor speed without mechanical sensor. It is also shown that the actual rotor position as well as the machine speed can be achieved under the variation of the magnet flux linkage. Since the flux linkages are estimated by the adaptive flux observer and used for the identification of the rotor speed, robust estimation of the rotor speed can be performed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.768-773
• /
• 1998

The speed control of SRM(Switched Reluctance Motor) needs the accurate position and speed data of rotor. This information is generally provided by a shaft encoder or resolver. In some cases, the environment is which the motor operates may cause difficulties in maintaining the satisfactory position detection performance. Therefore, the elimination of the position and speed sensor has gained wide attention. In this paper, a new algorithm for estimation of rotor position and speed is described for the SRM drives. This method uses is nonlinear adaptive observer using the MRAS(Model Reference Adaptive System). The observer is proved by Lyapunov Stability Theory. This algorithm was implemented with a TMS320C31 DSP. Experiment results prove that the observer is able to estimate the speed and position with a little errors.

• 한국기계가공학회지
• /
• 제11권2호
• /
• pp.47-54
• /
• 2012

An oxygen sensor installed in vehicle exhaust systems enables to measure the amount of oxygen in the exhaust gas, in which the measured data are collected and analyzed in ECU(Engine Control Unit). The oxygen sensor is exposed to the high speed exhaust gas at high temperature circumstance, so that protection caps are required not only to protect the susceptible measuring part, but also to provide the real time measurement without time delay. In this study, a new oxygen sensor with one protection cap was proposed, and the CFD analysis was carried out in order to compare the performance characteristics, such as flow speed and ratio of AOA(Age of Air), for the conventional and new oxygen sensor. The numerical results of CFD analysis provided the flow speed of 1.34m/s and the ratio of AOA of 3.43. The similar features obtained from the numerical results showed that the new oxygen sensor guarantees the same performance characteristics of the conventional ones.

• 전기학회논문지
• /
• 제61권2호
• /
• pp.298-302
• /
• 2012

The linear encoder used in the BLAC driving circuit consists usually analog type sensor, and need signal transform from analog sinusoidal to digital one for application in the PWM algorithm that is used to control motor current. When the motor is driven in low speed, it is required many operations and higher quality DSP to convert the hole sensor signal to digital one with enough resolution. In this paper, the another method to convert that signal with enough resolution without calculation of sine function is proposed. This is very simple and have high resolution even if the motor is driving in low speed. To verify the proposed method, BLAC motor is used, and it is proved that the motor is tracking well the reference step signal in the low speed as well as in the high one.

• Journal of Power Electronics
• /
• 제16권2호
• /
• pp.798-804
• /
• 2016

This paper proposes a new operation and control strategy for Power-Assisted Wheelchairs (PAW) using one brushless DC (BLDC) motor. The conventional electrical wheelchairs are too heavy and large for one person to move because they have two electric motor wheels. On the other hand, the proposed PAW system has a small volume and is easy to move due to the presence of a single wheel motor. Unlike the conventional electric wheelchairs, this structure for a PAW does not have a control joystick to reduce its weight and volume. To control the wheelchair without a joystick, a special control system and algorithm are needed for proper operation of the wheelchair. In the proposed PAW system uses only one sensor to detect the acceleration and direction of PAW's movement. By using this sensor, speed control can be achieved. With a speed control system, there are three kinds of operations that can be done on the speed of a PAW: the increment of PAW speed by summing external force, the decrement of PAW speed by subtracting external force, and emergency breaking by evaluating the time duration of external force. The validity of the proposed algorithm is verified through experimental results.

• 한국정보통신학회논문지
• /
• 제23권10호
• /
• pp.1188-1194
• /
• 2019

유체의 흐름을 측정하는 여러 방법 중 열선 풍속 센서는 유체의 열전달에 의해 속도나 온도를 측정하는 장치로 비정상 속도 및 난류 속도 성분을 측정하는데 유용하다. 하지만 열선 풍속 센서는 외부의 환경 요인에 민감하며, 주변 온도, 습도, 신호 잡음 등에 의해 정확도가 떨어지는 단점이 있다. 이런 단점을 보완하는 방법으로 온도 보상 회로를 추가하는 기술이 나오고 있지만 가격 경쟁력을 갖출 수 없는 상황이다. 이를 해결하기 위해 본 논문에서는 온도 보상이 필요 없는 풍속 감지 센서에 대해 연구를 진행하였다. 열선식 풍속 센서는 외부 환경 요인 중에서도 주변 온도에 매우 취약하다. 주변 온도로는 전자 회로에 의한 발열의 영향이 가장 크게 미치고 있으며, 이를 개선하는 방법으로 발열체에 보조 발열체를 추가로 장착하여 보조발열체와 발열체의 일정한 온도차를 제어하는 것이다. 이와 같이 기존 기술에 비해 복잡하지 않은 방법으로 동등한 성능을 확보할 수 있다는 것을 확인할 수 있었다.