• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.2
• /
• pp.123-130
• /
• 2013

This paper proposes the switched trans Z-source inverter(STZSI) which combined the characteristics of the trans Z-source inverter(TZSI) and the switched inductor Z-source inverter(SLZSI). The proposed STZSI has the same performance compared with the SLZSI which is improved the voltage boost performance of the conventional typical X-shaped ZSI, and it has advantage that circuit structure of Z-impedance network is more simple. And, in order to step up the voltage boost factor under the condition of the same duty ratio, unlike the SLZSI adding the inductors and diodes, the proposed method is dune by changing the turn ratio of trans primary winding of Z-impedance network. To confirm the validity of the proposed method, PSIM simulation and a DSP(TMS320F28335) based experiment were performed using trans with turn ratio 1 and 2 under the condition of the input DC voltage VI=50V, duty ratio D=0.1 and D=0.15. As a result, under the same input/ouput condition, the inverter arm voltage stress of the proposed method is reduced to about 15%-22% as compared with typical X-shaped ZSI, and the elements in Z-impedance network of the proposed method is reduced as compared with the SLZSI.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.2
• /
• pp.106-110
• /
• 2017

This paper compared current limiting characteristics of superconducting fault current limiter (SFCL) using E-I core due to the location of windings. Since E-I core has three legs and two magnetic paths, the current limiting characteristics of SFCL were expected to be affected by the installation location of windings, either center leg or right/left leg. To analyze its characteristics, the electrical equivalent circuit of the SFCL were derived and the electromagnetic analysis for the SFCL with the designed structure were performed. From the short-circuit tests, the hysteresis curve and the voltage-current trajectory of the SFCL due to the installation location of windings were extracted and compared each other. The SFCL with windings in the center leg of E-I core was shown to be larger magnetizing inductance compared to the one with windings in the right or left leg of E-I, which was analyzed from the hysteresis curve. In addition, larger decreased fault current right after the fault occurrence in the SFCL with windings in the center leg of E-I core was confirmed than the SFCL with windings in the right or left leg of E-I.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.5
• /
• pp.173-181
• /
• 1993

Under natural conditions, rivers do not in general take straight courses but instead take winding courses. This is known as meandering of rivers. Meandering of rivers are so complicated because of the mutual interactions between flow and movable boundaries. In quantitative information, it is important to predict the future location of a river channel(channel migration) because in selecting a bridge site or a location of a road. It may be valuable to know the future impact of a nearby river on those structures. When the prediction model of the migration of channel is used in domestic rivers with high coefficient of river regime, it is rational to use the periodical dominant discharge (PDD), which is named firstly by the author, instead of the average discharge. According to the analysis of the erosion coefficient, the mean deviation on the channel migration, and the bed scour factor, it can bring shedding light on the fact that the discharge is one of the dominant components in channel migration. In project area, the discharge that can shift the channel is slightly greater than 6,000CMS. The prediction model of the migration of channel estimated the erosion coefficient, $E_0$ by the data from the South Han River. This estimated value from the South Han River was also used to predict the migration of the South Han River in year 2000.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.169-172
• /
• 2005

A flywheel system is an electromechanical energy storage device that stores energy by rotating a rotor. The rotating part, supported by magnetic bearings, consists of the metallic shaft, composite rims of fiber-reinforced materials, and a hub that connects the rotor to the shaft. The delamination in the fiber wound composite rotor often lowered the performance of the flywheel energy storage system. In this work, an advanced hybrid composite rotor with a split hub was designed to both overcome the delamination problem in composite rim and prevent separation between composite rim and metallic shaft within all range of rotational speed. It was analyzed using a three-dimensional finite clement method. In order to demonstrate the predominant perfom1ance of the hybrid composite rotor with a split hub, a high spin test was performed up to 40,000 rpm. Four radial strains and another four circumferential strains were measured using a wireless telemetry system. These measured strains were in excellent agreement with the FE analysis. Most importantly, the radial strains were reduced using the hybrid composite rotor with a split hub, and all of them were compressive. As a conclusion, a compressive pressure on the inner surface of the proposed flywheel rotor was achieved, and it can lower the radial stresses within the composite rotor, enhancing the performance of the flywheel rotor.

• Journal of the Korean Magnetics Society
• /
• v.25 no.2
• /
• pp.58-65
• /
• 2015

This paper deals with the generating characteristic analysis of permanent magnet linear generator (PMLG) with double-sided Halbach magnet array mover and three phases concentrated stator windings by using analytical method. On the basis of a magnetic vector potential and Maxwell's equations, governing equations are obtained, and magnetization modeling for Halbach magnet array is performed analytically by using the Fourier series. And then, we obtain electrical parameters such as back-EMF constant, resistance, and coil inductance based on magnetic field calculations. Finally, analytical results for generating performance are confirmed by comparing with finite element analysis results.

• Journal of the Korean Institute of Gas
• /
• v.15 no.1
• /
• pp.35-39
• /
• 2011

The purpose of this paper is to analyze affecting ratios of strength safety in carbon fiber layer thickness of a composite fuel tank for FEV vehicles. To investigate affecting ratios by FEM modeling, the equivalent von Mises stress has been computed on the aluminum liner and carbon fiber layers of composite fuel tanks in hoop and helical directions respectively. According to the FEM results, the affecting ratios of an aluminum liner on the equivalent stress are 77.5% in hoop direction, 18.11% in $70^{\circ}C$ winded helical direction and 4.39% in $12^{\circ}C$ winded helical direction. These trends on the strength safety of carbon fiber layers have been shown as those of an aluminum liner even though the layer thickness ratio of $12^{\circ}C$ inclined carbon fiber is very high of 42% compared with that of hoop layer thickness. Thus, the computed results show that the strength safety of a carbon fiber fuel tank is more influenced by the winding angle rather than the fiber thickness of carbon fiber layers.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1297-1300
• /
• 2008

A conventional linear accelerator system requires a flat-topped pulse with less than ${\pm}$ 0.5% ripple to meet the beam energy spread requirements and to improve pulse efficiency of RF systems. A pulse transformer is one of main determinants on the output pulse voltage shape. The pulse transformer was investigated and analyzed with the pulse response characteristics using a simplified equivalent circuit model. The damping factor ${\sigma}$ must be >0.86 to limit the overshoot to less than 0.5% during the flat-top phase. The low leakage inductance and distributed capacitance are often limiting factors to obtain a fast rise time. These parameters are largely controlled by the physical geometry and winding configuration of the transformer. A rise time can be improved by reducing the number of turns, but it produces larger pulse droop and requires a larger core size. By tradeoffs among these parameters, the high-voltage pulse transformer with a pulse width of 10 ${\mu}s$, a rise time of 0.84 ${\mu}s$, and a pulse droop of 2.9% has been designed and fabricated to drive a klystron which has an output voltage of 284 kV, 30-MW peak and 60-kW average RF output power. This paper describes design optimization of a high-voltage pulse transformer for high-power pulsed applications. The experimental results were analyzed and compared with the design. The design and optimal tuning parameter of the system was identified using the model simulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.5
• /
• pp.43-50
• /
• 2003

This presents a fault detecting method for a power transformer based upon a neural network. To maintain a normal relay operating conditions, external winding faults of a power transformer and magnetic inrush have been tested under consideration of the EMTP/ATP software and internal faults of power transformer have been tested by the EMTP/BCTRAN software. The neural network has been evaluated by the proposed fault. Input variables of the neural network for the proposed model can be obtained from fundamental currents, restraining and operating currents. This algorithm uses back-propagation and the ratio of a restraining current and an operating current as relay input parameters. The ratio may enhance the fault detection since the restraining currents increase rapidly at external faults. The proposed detecting method has been applied to the practical relay systems for transformer protection. As a result, the proposed detecting method based on the neural network has been shown to have better characteristics.

• Journal of the Korean Society of Costume
• /
• v.60 no.5
• /
• pp.51-70
• /
• 2010

The ritual to change the hairstyle holds the same meaning as the coming of age ceremony. The ceremony was performed throughout three times including choga, jaega, and samga. The garment and hairstyle attuned to the ceremony formalities. Women in the royal family had 'su-siK when they were fully grown up during choga, 'gwang-sik' during Jaega, and 'keun-meo-ri (big hairstyle)' during samga. 'su-sik' is the noblest hairstyle according to social status, which is allowed to be worn only by spouse of king and prince, regardless of adult or not. During jaega, 'gwang-sik' which was 'u-yeo-meo-ri', is made by winding 'darae (wig)' around a jjok-jin-muri (bun) [Jo-jim-meo-ri]? which distinguished the hairstyle of unmarried women, who did not go through a coming of age ceremony yet. Unmarried women maintained a hairstyle which is mostly twisted into one string, but they had 'saeang-meo-ri' when they were prepared for ceremonial costumes. Also, they had 'ga-raemeo-ri' when growing further. keun-meo-ri during samga is an addition of keun-meo-ri chaebal(wig) onto u-yeo-meo-ri. Women in the royal family made geo-du-mi by adding keun-meo-ri, which is formed by twisting wig, and oimyeongbu (noble ladies) and sanggung (court ladies) added a wooden wig called u-yeo-mi. Also, yeoryeong wore ga-ri-ma. In this way, the types of hairstyles were distinguished according to hierarchy. As the coming of age ceremonial dress. Wonsam was worn. During choga. wonsam was worn as a formal dress and during jaega and samga wonsam was worn as a full dress.

• Composites Research
• /
• v.15 no.1
• /
• pp.53-60
• /
• 2002

Composite ablative tubes required capabilities of ablative and structural characteristics were fabricated through filament winding technique and several experiments were conducted to evaluate the structural performance of composite ablative tubes. For this purpose, manufacturing procedures were briefly described and then resin digestion method was applied to measure the fiber volume fraction and the void content of composite ablative tubes. The configuration of tensile specimen fur composite ablative tubes with not losing the continuity of reinforced fibers was suggested by evaluating mechanical properties of several types of the specimen with different widths. Also, suitable processing variables for composite ablative tubes were determined by evaluating mechanical properties of several types of the specimen with different processing variables. In addition, acoustic emission signals were obtained during the proof test and could be applicable to study the crack initiation and the damage mode of composite ablative tubes. Finally, the structural reliability of composite ablative tubes could be verified to satisfy design requirements through the proof and burst tests.