• Journal of Magnetics
• /
• 제13권4호
• /
• pp.167-169
• /
• 2008

The switching field of a 300 nm wide nanowire has been controlled by attaching a wide wire to it. The width of the wide wires varies from 700 nm to 2000 nm. While the connection of the two wires does not affect the switching field of the wide wires, it strongly affects the 300 nm-wire, resulting in a decrease of the switching field of the isolated wire from 175 Oe to 54 Oe when the 2000 nm-wire is connected to it. This result clearly shows that the switching field of the nanowire can be engineered by attaching a nucleation pad that has a different magnetic anisotropy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.3-5
• /
• 2008

This paper presents a hybrid winding connection method for torque characteristics improving of a traction SRM. In order to get a high torque in wide speed range and torque ripple reduction, series and parallel winding connection are changed according to operating speed. From the analysis of torque character operation mode and efficiency, the proposed control scheme is verified.

• 교육녹색환경연구
• /
• 제10권2호
• /
• pp.1-7
• /
• 2011

An experimental study to evaluate structural capacity of an embedded plate connected with prestressed concrete beam was performed. Embedded steel plates and prestressed concrete beam were connected with stud-bolts at the ends of concrete beam specimens. About 1,000 kN concentrated load was applied at 450mm away from the end of beam specimen. A 3,000 kN capacity static Oil-jack was used to direct concentrated load. The maximum strain of stud-bolt recorded $90{\times}10^{-6}$(mm/mm) and wide width cracks were not founded. Any falling failures of concrete and large deformations were not founded either between steel plate and prestressed concrete specimen. As a result, construction performance can be improved using this embedded steel plate connection system apply to large space educational facilities.

• 한국해양공학회지
• /
• 제14권4호
• /
• pp.79-85
• /
• 2000

Press-fit pin connection is the solderless interference-fit between pins and plated through holes(PTH) in the printed curcuit board(PCB). Because of not only its simple assembly and absence of problems associated with soldering, but also its good mechanical and electrical characteristics, the press-fit pin connection technology has quickly gained wide acceptance in the telecommunications and computer industries. In this paper, the contact stress characteristics of the domestic CPF pin when inserted into the friction coefficients were compared and the stress variations of the compliant part of the pin, which have an influence on the performance, were displayed with the time and arc length after complete connected. It is supposed that the results will provide useful data to improve the performance of the pin-PCB interconnection mechanism.

• Steel and Composite Structures
• /
• 제4권6호
• /
• pp.453-469
• /
• 2004

In this article, a genetic algorithm based optimum design method is presented for non-linear steel frames with semi-rigid connections. The design algorithm obtains the minimum weight frame by selecting suitable sections from a standard set of steel sections such as European wide flange beams (i.e., HE sections). A genetic algorithm is employed as optimization method which utilizes reproduction, crossover and mutation operators. Displacement and stress constraints of Turkish Building Code for Steel Structures (TS 648, 1980) are imposed on the frame. The algorithm requires a large number of non-linear analyses of frames. The analyses cover both the non-linear behaviour of beam-to-column connection and $P-{\Delta}$ effects of beam-column members. The Frye and Morris polynomial model is used for modelling of semi-rigid connections. Two design examples with various type of connections are presented to demonstrate the application of the algorithm. The semi-rigid connection modelling results in more economical solutions than rigid connection modelling, but it increases frame drift.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.922-925
• /
• 2004

Bluetooth technology is essentially a method for wireless connection of a diverse set of devices ranging from PDAs, mobile phone, notebook computers, to another equipments. The bluetooth system supports both point-to-point connection and point-to-multipoint connections. In point-to-multipoint connection, the channel is shared among several bluetooth devices. Two or more devices sharing the same channel form a piconet. There is one master device and up to seven active slave devices in a piconet. The radio operates in the unlicensed 2.45GHz ISM band. This allows users who travel world-wide to use bluetooth equipments anywhere. Since the link is based on frequency-hop spread spectrum, multiple channels can exist at the same time. The Bluetooth standard has been suggested that Bluetooth equipments can be used in the short-range, maximum 100 meters . It has been defined that the time takes to setup and establish a bluetooth connection among devices is 10 seconds. It is a long time and may be a cause to lose a chance of finding other non-fixed devices. We propose a routing protocols for scatternets which can be used to control a mobile units(MUs) in this network. The proposed routing protocol is composed of two kinds of bluetooth information, access point(AP) and MU.

• Steel and Composite Structures
• /
• 제25권3호
• /
• pp.271-286
• /
• 2017

The use of Hollow Structural Sections (HSS) provides an alternative for steel buildings in seismic zones, with the advantage over WF columns that the HSS columns have similar resistance along both axes and enhanced performance under flexure, compression and torsion with respect to other columns sections. The HSS columns have shown satisfactory performance under seismic loads, such as observed in buildings with steel moment frames in the Honshu earthquake (2011). The purpose of this research is to propose a new moment connection, EP-HSS ("End-plate to Hollow Structural Section"), using a wide flange beam and HSS column where the end plate falls outside the range of prequalification established in the ANSI/AISC 358-10 Specification, as an alternative to the traditional configuration of steel moment frames established in current codes. The connection was researched through analytical, numerical (FEM), and experimental studies. The results showed that the EP-HSS allowed the development of inelastic action on the beam only, avoiding stress concentrations in the column and developing significant energy dissipation. The experiments followed the qualification protocols established in the ANSI/AISC 341-10 Specification satisfying the required performance for highly ductile connections in seismic zones, thereby ensuring satisfactory performance under seismic actions without brittle failure mechanisms.

• 인터넷정보학회논문지
• /
• 제2권5호
• /
• pp.81-91
• /
• 2001

XML은 웹에서 구조화된 정보나 반-구조화된 정보를 교환하고 저장하는데 있어서 하나의 표준 마크업 언어로 채택되고 있는 추세이다. 웹을 통한 정보교환에 있어서, XML 메시지의 소스 데이터는 Legacy 데이터베이스에 저장되어 있기 때문에 XML 응용과 데이터베이스 시스템과의 원활한 연계가 요구되어진다. 이를 위하여 Oracle8i와 9i 및 Informix 그리고 SQL2000과 같은 DBMS들은 XML을 취급하기 위하여 자신의 DBMS들을 확장하고 있다. 그러나 이러한 방법은 플랫폼-종속적이며 DBMS-종속적이다. 따라서 원활한 XML 응용과 데이터베이스 시스템과의 연계를 위해서는 플랫폼-독립적이며 DBMS-독립적인 연계방안이 요구된다. 이에 따라 본 논문에서는 XML응용과 기존의 데이터베이스 시스템과의 원활한 연계를 위하여. XML DTD를 토대로 관계형 데이터베이스 스키마를 설계하기 위한 미들웨어 컴포넌트를 설계하였다.

• 제어로봇시스템학회논문지
• /
• 제10권11호
• /
• pp.1052-1057
• /
• 2004

Bluetooth technology is essentially a method for wireless connectivity of a diverse set of devices ranging from PDAs, mobile phone, notebook computers, to another equipments, The bluetooth system both point-to point connection and point-to multipoint connection. In point-to multipoint connection, the channel is shared among several bluetooth devices. Two or more devices sharing the same channel form a piconet. There one master device and up to seven active slave devices in a piconet. The radio operates in the unlicensed 2.45GHz ISM band. This allows users who travel world-wide to use bluetooth equipments anywhere. Since the link is based on frequency-hop spread spectrum, multiple channels can exist at the same time. The bluetooth standard ha s been suggested that bluetooth equipments can be used in the short-range, maximum 100 meters. It has been defined that the time takes to setup and establish a bluetooth connection among devices is 10 seconds. It is a long time and may be a cause to lose a chance of finding other non-fixed devices. We propose a routing protocols for scatternets which can be used to control a mobile units(MUs) in this network. The proposed routing protocol is composed of two kinds of bluetooth information, access point(AP) and MU.

• 한국통신학회논문지
• /
• 제32권7B호
• /
• pp.431-437
• /
• 2007

웹 프록시 캐슁은 원하는 데이터를 접근하기 위한 지연시간과 요구하는 통신망의 대역폭을 줄이는데 효과적인 방법을 제공한다. 특히 프리픽스 캐슁은 비디오 WAN에서 비디오 전송을 위한 대안으로서 간주되는데 이는 비디오 데이터는 그 양이 너무 커서 데이터 전체를 캐쉬에 저장하는데 문제를 야기시키기 때문이다. 또한 최근의 많은 연구결과에 의하면 사용자가 인식하는 지연시간은 데이터를 전송하는 전송시간에 의해 영향을 받는 것이 아니라 TCP 연결설정 시간과 같이 데이터 전송단계를 선행하는 설정과정에 의해 많은 영향을 받는다는 것이다. 본 논문은 프록시 캐슁에서 사용되는 TCP pre-connecting 기법을 제안하며 이 기법이 TCP splicing에서 효율적으로 사용될 수 있다는 것을 보인다. 아울러 제시된 수치적인 모델은 start-up 지연시간을 줄일 수 있음을 보인다. 제안된 기법은 어떠한 프로토콜 수정이나 다른 엔티티와의 동작을 요구하지 않는다.