• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.555-564
• /
• 2001

Wheel-rail noise is normally classified into three catagories ： rolling, squeal and impact noise. In this paper, rolling noise caused by the irregularity between a wheel and rail is analysed as follows： The irregularity between the wheel and rail is assumed as combination of sinusoidal profiles. Wheel-rail contact stiffness is linearized by using Hertzian contact theory, and then contact force between the wheel and rail is calculated. Vibration of the rail and wheel is calculated theoretically by receptance method or FEM depending on the geometry of wheel or rail for the frequency range of 100-5000Hz, important for noise generation. The radiation caused by those vibration is computed by BEM. To verify this analysis tools, rolling noise is calculated by preceding analysis steps using typical roughness data and it is compared with experimental rolling noise data. This analysis tools show reasonable results and used for the prediction of KTX rolling noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.328-333
• /
• 2002

When vehicle travelling along the track which has irregularity such as vertical profile, dynamic forces arise at the Wheel/Rail contact patch by wheel/rail interaction. In particular short wavelength irregularities on dipped joint and small stiffness of connecting rail bring about intense wheel/rail dynamic effects at higher speed. In the paper, a new model for dipped joint rail is developed to study dynamic behavior of track. A cusp behavior on dipped joint was defined by its amplitude and decay factor, which was presented by FRA track classes. The result of case study are presented, which show wheel rail contact force in each track classes, train operation speed and bending flexible rigidity ratio of fishplates which are connecting the rail.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.663-667
• /
• 2003

Mechanical force acted on the rail wheel causes excessive wear and increases the maintenance cost. The present paper proposes newly designed wheel profiles in order to reduce the contact stress. Numerical analysis on the stress distribution of wheel-rail contact stress is carried out using ABAQUS, a commercial finite element code. The result of KNR1/40 conical wheel is compared to those of the proposed wheels, all of which are arc wheel profile type.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2135-2146
• /
• 2011

The rail surface irregularity is generated severely by train braking effect in the section of station. The braking force increases slip rate and friction factors caused by wheel-rail contact points. It brings rail surface irregularity as well. In this study, interactions between wheel and rail were investigated using rolling contact fatigue theory and mechanism of rail degradation through fracture mechanics. For the more, the Von-Mises stress occurred on the rail due to the interaction between wheel and rail was analyzed using 3-D finite element method. The amounts of surface irregularity of rail were measured according to accumulated passing tonnage in urban railway in fields. Therefore, the maintenance of rail should be separated by running and braking sections to prevent RCF defects.

• International Journal of Railway
• /
• v.7 no.4
• /
• pp.109-116
• /
• 2014

For optimization of a low-noise track system, rail vibration and noise radiation needs to be investigated. The main influencing parameters for the noise radiation and the quantitative results of every track system can be obtained using a calculation model of generation and radiation of railway noise. This kind of model includes contact modeling and the calculation model of the dynamic properties of the wheel and the rail. This study used a nonlinear wheel/rail interaction model in the time domain to investigate the excitation of the rolling noise. Wheel/rail response is determined by time integrating Green's function of the rail together with force impulses from the wheel/rail contact. This model and the results of the study can be used for supporting calculation with the conventional model by an addition of the contributions due to nonlinearities to the roughness spectrum.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1128-1133
• /
• 2011

This is a testing equipment system to analyze variation of creep force according to wheel-rail tread profile, running speed of vehicle, vertical and lateral force, wheel/rail contact point, attack angle and so on. The creep force affect vehicle derailment, especially climbing derailment. This system is composed of main frame, wheelset and rail disks driver, hydraulic actuator, controller, environmental chamber, safety system and so on.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.481-484
• /
• 2008

The important factor to evaluate the running safety of a railway vehicle would be the interaction force between wheel and rail(derailment coefficient), for which is one of important factors to check the running safety of a railway vehicle that may cause a tragic accident. Element that analyze derailment coefficient is consisted of wheel load and lateral force. In this paper, studied about method that calculate vertical force(wheel load) by bending load of axle in rolling stocks.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1487-1488
• /
• 2010

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.1115-1120
• /
• 2005

characteristic of wear between wheel and rail is important factor of judgement to maintenance. KHST is optimized on an exclusive rail, UIC60. but also KHST is running on the variety existing line as well as KS50N, KS60 et,c. Hail profile of KS50N is dissimilar to DIC60. So we can predict that characteristic of wear is embodied also different. In this paper. we deduced the force and point of contact position between wheel and rail through multi-dynamics analysis and predicted wear of wheel and rail through contact problem analysis. we used simplified theory of kallker on contact problem, and Predicted the wear phenomenon of wheel using archard wear equation about each condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.411-412
• /
• 2006

It is very difficult to analyze the dynamic characteristic because railway vehicle is a very complex system which are connected various mass element with railway vehicle system. To realize and analyze actual phenomenon has restriction that usual commercial software calculates creep force under creep theory about wheel-rail contact mechanism as basic analyzing, and approach about contact point are based on two dimensional non-linear contact theory and simplified Hertzian contact which considers just displacement change on the YZ plain. Therefore, to solve these problems there should be a new approach difference with existing one. In this research, a new algorithm for finding wheel-rail contact position, calculation method of contact force and applied force will be presented.