• 한국주거학회논문집
• /
• 제15권3호
• /
• pp.63-72
• /
• 2004

The objective of this study is to survey and analyze convenience of the disabled people to use the facilities in accommodations. The data used in this research has been obtained in the southern sea of Korea. According to the survey, it was very difficult for the disabled people with a wheel chair to access to the room because of the staircase, doorsill and the narrowed passage. Also, there was no the grab bar, braille blocks and exclusive elevators for the disabled. Moreover, it was not easy for them to access to the bedroom since there was a doorsill and a serious height difference between the lobby and the bedroom. It was shown that the disabled People also have a difficulty in using the toilet and the bathroom, because the width of door and floor height was not suitable for the design criteria. In the toilet, there was no handle on a chamber pot for the disabled people to hold, and the space was not enough for them to access to the pot and turn with a wheel chair.

• 한국정밀공학회지
• /
• 제26권9호
• /
• pp.72-80
• /
• 2009

When the magnet wheel rotates over a conducting plate, it generates the traction torque as well as the repulsive force on the conducting plate. Partially-cut traction torque results in the linear force into the tangential direction. To cut the traction torque, the concept of magnetic shield is introduced. The direction change of the linear force is realized varying the shielded area of magnetic field. That is, the tangential direction of non-shielded open area becomes the direction of the linear thrust force. Specially a shape of permanent magnets composing the magnet wheel leads to various pattern of magnetic forces. So, to enlarge the resulting force density and compensate its servo property a few simulations are performed under various conditions such as repeated pattern, pole number, radial width of permanent magnets, including shape of open area. The theoretical model of the magnet wheel is derived using air-gap field analysis of linear induction motor, compared with test result and the sensitivity analysis for its parameter change is performed using common tool; MAXWELL. Using two-axial wheel set-up, the tracking motion is tested for a copper plate with its normal motion constrained and its result is given. In conclusion, it is estimated that the magnet wheel using partial shield can be applied to a noncontact conveyance of the conducting plate.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.51-56
• /
• 2011

The train travels on the track and, thus, the rear wheels precisely follow the paths of the front wheels. On the contrary, in the vehicles running on the road like automobiles, buses and trucks, the front wheels try to drag the rear ones toward them and across the inside of the curve. Off-tracking is defined as the radial offset between the path of the centerline of the front axle and the path of the centerline of the following axle. In the case of the bimodal tram with AWS(all wheel steering), the off-tracking decrease but the rear swing-out values increase because of the rear steering at the reverse phase angle. Thus, in order to determine the swept path width, maximum road width at the minimum turning radius, off-tracking and swing-out should be considered for the bimodal tram. In this paper, trajectory simulations were carried out for the various condition such as front steering, front and rear steering and suppression of swing-out to optimize the swept path width.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 2002년도 춘계학술대회 및 임시총회
• /
• pp.10-13
• /
• 2002

본 연구에서는 다기능 휠체어 시스템을 개발하기 위해 제어부를 16bit의 마이크로 프로세서인 80C196KC 사용하였고, 조이스틱을 통해서 된 시스템을 제어하는 것을 구현하였다. 전체시스템은 제작된 전동 휠체어 기본 Plant를 사용하였으며, 모터에서 Encoder로 입력받아 MCU를 통해서 휠체어 회전수를 이용하여 제어시켰다. 휠체어 모터의 제어 방법은 PWM(Pulse Width Mudulation)을 이용하였으면, 여기에 H-브릿지 회로를 구성하였다. 조이스틱을 사람의 손으로 제어하는데 있어서 조이스틱 위치 변화에 따른 전동휠체어에 부착된 DC모터 동작을 퍼지 제어 알고리즘을 사랑하였으며, DC모터의 속력과 방향을 제어하고 아울러 위치 정보까지도 제어할 누 있게끔 하였다.

• 한국철도학회논문집
• /
• 제14권6호
• /
• pp.535-544
• /
• 2011

레일 표면 결함이 발생할 경우 매우 높은 충격하중이 발생하여 레일 피로 진전 또는 레일 파단에 이를 수 있고 레일이 파단될 경우 열차탈선 등 대형 사고가 발생할 수 있으므로 레일 결함부에 대한 관리기준의 정립이 매우 중요하다. 본 연구에서는 차량-궤도 동적 상호작용 해석 프로그램을 이용하여, 실제 고속철도 자갈궤도에서 결함이 발생한 43개 지점에서 측정된 레일요철을 입력값으로 하여, 요철 깊이에 따른 충격 윤중과 레일 휨응력을 산정하였다. 궤도틀림을 감안하여 윤중 및 레일 휨응력의 한계값을 설정하고, 해석결과로부터 얻은 윤중 및 레일 휨응력 최대값과 결함 깊이 및 폭과의 상관관계를 분석함으로써 레일 표면 결함부에 대한 관리기준을 제시하였다. 분석 결과, 허용할 수 있는 요철 깊이는 충격 윤중에 의하여 발생할 수 있는 레일 두부의 소성 변형을 방지하기 위하여 관리되어야 하며, 엄격한 조건을 평가할 경우 그 값은 0.2mm 정도가 적당함을 알 수 있었다.

• 대한안전경영과학회지
• /
• 제15권4호
• /
• pp.123-129
• /
• 2013

Among various manual materials handling tasks, pushing/pulling was known to be one of the risk factors for the low back and shoulder musculoskeletal disorders (MSDs). This study was conducted to find out an optimal solution set of the handle height and distance for 4-wheel cart with two vertical handles. Ten male college students participated in the pushing force measurement experiment. The face-centered cube design, one of the central composite designs, was applied for the experiment, and the isometric voluntary pushing force was measured in 9 treatment conditions. The second order response surface model was predicted by using the pushing strength as a response variable, and the handle height and distance as independent factors. According to the 2nd order response model, the handle height and distance showed nonlinear relationship with the isometric pushing strength. To maximize the 2nd order response model (pushing force), the handle height and distance were optimized. The optimal handle height was 'xyphoid process height - stature', and the optimal handle distance was '$1.25{\times}shoulder$ width'. When calculated using the anthropometric data of the subjects of this study, the optimal handle height was $115.4{\pm}3.4$ cm, slightly higher than the elbow height, and the handle distance was $52.9{\pm}2.3$ cm.

• 한국정밀공학회지
• /
• 제23권4호
• /
• pp.132-138
• /
• 2006

A tape feeder is an important part to supply a micro chip such as 1005 and 0603 components in SMT process. Traditional sprocket wheel type feeder has several problems such as backlash and indexing errors, low compatibility and confidence. However, it is very difficult to solve such problems due to the inevitable fraction defectives of sprocket wheel. Thus, the object of this works is to develop a linear type high precision tape feeding system using cam-slider mechanism. The proposed cam-slider mechanism is composed of several links and a plate, pneumatic actuator is used to generate linear motion. The proposed mechanism has distinct advantages over the conventional mechanism. It has reduced feeding errors, long lift-cycle, and slim width. As a result, the developed tape feeder using cam-slider mechanism shows special characteristics far high precision feeding for chip-mounters.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.554-554
• /
• 2000

To improve mechanical properties of Cu-Al-Ni alloy by the grain refinement, Cu-Al-Ni SMA ribbons were fabricated by melt spinning apparatus. The variations of microstructure, mechanical properties and transformation characteristics with the condition of rapid solidification and annealing time-temperature were investigated in Cu-Al-Ni SMA ribbons. The ribbons fabricated by melt spinning obtained around 1.5nm in width and 50-60${\mu}{\textrm}{m}$ in thickness. With increasing wheel speed in order of 10m/s, 15m/s, 20m/s, 30m/s and 3m/s, the grain size was decreased in order of 10${\mu}{\textrm}{m}$, 6.25${\mu}{\textrm}{m}$, 5.5${\mu}{\textrm}{m}$, 3${\mu}{\textrm}{m}$ and 3${\mu}{\textrm}{m}$. $M_{s}$ and $A_{s}$ temperature were decreased with decreasing grain size. By X-ray diffraction test, ordered $\beta$$_1$ phase was observed in all the SMA ribbons and the volume friction of it was increased with increasing wheel speed. With increasing wheel speed, strain was increased from 4.2% to 5.8% and fracture mode has changed from mixture of intergranular and dimple fracture to mixture of fiber structure and dimple fracture. The grain size of ribbon heat-treated at $600^{\circ}C$ was increased with increasing time. In the heat-treated ribbons at 55$0^{\circ}C$, ${\gamma}$$_2$ phases were observed.d.d.

• Journal of Biosystems Engineering
• /
• 제29권6호
• /
• pp.487-494
• /
• 2004

This study was conducted to develope a fertilizer-soil incorporation band tiller for the walking cultivator. Because the mixing of soil and fertilizer in the furrow of dry-field has been done manually, several time, heavy labor and much man power were required for the job. This rotary type implement is developed to substitute this manual operation for soil-fertilizer incorporation. The results of this study are summarized as follows : 1) This implement was composed of tilling device, fertilizer application device, frame and tail wheel device. 2) The revolution of driving wheel was $11\~28\;rpm$, that of application roller was $13\~14\;rpm$ the application rate range per revolution of driving wheel was $4.43\~11.80\;g$g and the application rate range by the working speed and the opening quantity was $84.12\~557.20\;g/min$. 3) The adequate working speed was $0.20\~0.40\;m/s$ and the required minimum width of open furrow was 250 mm.

• 한국안전학회지
• /
• 제34권5호
• /
• pp.103-110
• /
• 2019

In order to reduce the accidents occurring at construction sites, it is necessary to approach with harmonious measures considering various aspects such as systems, training, facilities, and protection equipments. Suggestion of safe construction method can be a good alternative. In the previous study, the half-depth precast deck with RC rib panel was proposed as an alternative method for safe bridge deck construction, and the performance required by the design code was verified through a four-point bending test. But the actual bridge deck is subjected to the repetitive action of the wheel load rather than the bending condition due to the four-point load. In this study, fatigue test was performed by repeating the wheel load $2{\times}10^6$ cycles to verify the safety of the half-depth precast deck with RC rib panel under actual conditions. As a result, fatigue effect due to repetition of wheel load was not significant in terms of serviceability such as crack width and deflection. In the residual strength test conducted after the fatigue test, the half-depth precast deck with RC rib panel failed by punching shear which is typical failure mode of bridge decks and the residual strength was similar to the punching strength of the RC and PSC bridge decks in spite of the fatigue effects.