• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.621-626
• /
• 2006

Regenerative evaporative cooling is known as an environment-friendly and energy efficient cooling method. A regenerative evaporative cooler (REC) consisting of dry and wet channels is able to cool down the air stream below the inlet wet-bulb temperature. In the regenerative evaporative cooler, the cooling effect is achieved by redirecting a portion of the air flown out of the dry channel into the wet channel and spraying water onto the redirected air. In this study, a horizontal regenerative cooler is considered. In the horizontal regenerative cooler, the flow direction of evaporating water has a right angle to the flow direction of supply air. This difference was investigated with visualization technique and simplified 2-module performance test was done in a thermo-environment chamber. Optimum design configuration is changed due to the wet channel which are easily fully covered with evaporating water and block the air flow inside the channel. Applying the optimized fin configuration design with the highly wetting surface treatment, a regenerative evaporative cooler was fabricated and tested to Identify the cooling performance improvement and operation characteristics. From the experimental results at the intake condition of $32^{\circ}C$ and 50% RH, the supply temperature was measured to be around $23.4^{\circ}C$. The cooling effectiveness based on the inlet dewpoint temperature was evaluated 73% which is almost close to the design expectation.

• Korean Journal of Materials Research
• /
• v.11 no.8
• /
• pp.666-670
• /
• 2001

To improve the corrosion resistance of separator wet-seal area which is the barrier of commercialization of molten carbonate fuel cell(MCFC), Ni/Y/Al coating layer was fabricated by Ni electroplating and Y, Al e-beam PVD on AISI 316L stainless steel. NiAlY alloy coating layer was formed by heat treatment in reduction atmosphere at $800^{\circ}C$ for 5hr. Immersion test in molten carbonate salt at $650^{\circ}C$ was performed on as- received AISI 316L stainless steel and NiAlY coated specimen. According to cross sectional SEM/EDS observations, corrosion resistance of separator wet-seal area was improved by formation of dense oxide layers of Al and Y.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.2
• /
• pp.77-82
• /
• 2011

The changes in the wet pressing response of old corrugated container(OCC) stock depending on the beating treatment and the addition of polymer aids were investigated with laboratory roll press instrument. Two types of polymer aids, such as high molecular weight polymer with low charge density and low molecular weight polymer with high charge density, were applied in this study. The more beaten OCC stock showed the lower dryness after wet pressing. The addition of polymer aids had great influences on the wet pressing efficiency and paper properties. The dryness after wet pressing was increased by the addition of polymer aids, but the pattern of changes in dryness were different depending on the type of polymer and the properties of stock. The higher molecular weight polymer aids showed the greater increase in the dryness. The properties of paper such as air permeability, bulk, formation, tensile strength were also greatly affected by the addition of polymer aids.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.63-72
• /
• 1999

For the purpose of improving the wet strength properties of paper, cellulosic fibers were modified by the processes of carbarmoylethylation and N-chlorocarbamoylethylation. Carbamoylethylated cellulose was prepared by the reaction of acrylamide with cellulosic fibers under the alkali catalyst, and N-chlorocarbamoylethylated cellulose was prepared by the addition of sodium hypochlorite into the carbamoylethylated cellulose. In carbamoylethylation reaction, the conditions of NaOH concentration, temperature and acrylamide addition rate were considered to be important factors. An initial reactivity and degree of substitution(DS) in carbamoylethylation of cellulosic fibers were effective according to increasing the addition rates of alkali, acrylamide and the temperature condition of $40^{\circ}C$. The effective wet strength properties by N-chlorocarbamoylethylation of cellulosic fibers were indicated under the conditions of DS 0.06. The wet strength of sheet was improved to 85% at the 100% basis of dry strength. From the photograph of scanning electron microscopy, fiber cuttings on the edge of sheet sample used in tensile strength testing were found in the N-chlorocarbamoylethylated sheet, due to the improvement of fiber bonding strength. The hypochlorite treatment was effective in the recycling of N-chlorocarbamoylethylated sheet, and was reduced the wet strength of sheet to be able to reslush.

• Journal of the Korea Computer Graphics Society
• /
• v.23 no.1
• /
• pp.9-16
• /
• 2017

Simulating the clumping and stiffness of wet hair or fur is a challenging problem. The dynamics of wet hair or fur is characterized by the clumping and stiffness at the tip, which is easily seen in running animals or headbanging scenes. Existing methods address these phenomenon within pre-set scenarios. But there is no consensus on the method of depicting the details of wet hair. Hence, the present paper proposes a new method of modeling the clumping and stiffness of wet hair or fur. Previous studies focused on modeling the absorption of water into hair or fur, whereas this paper highlights a realistic simulation of wet hair. Unlike dry hair strands, wet hair strands adjacent to one another are subjected to the clumping force and gather together, while at the same time becoming stiff as the saturation of water increases. The proposed method builds on the surface tension model based on SPH (smoothed particle hydrodynamics) to simulate the clumping force and to adjust the hair elasticity by giving stiffness constraints. The present method enables a realistic simulation of wet hair by maintaining the clumping force of the wet hair even in dynamic motions, and by simulating the stiffness of hair in line with water saturation.

• Fashion & Textile Research Journal
• /
• v.3 no.5
• /
• pp.466-472
• /
• 2001

To find a suitable condition in this process examined, we investigated the main control factors, such as, the NaOH concentrations, such as, the NaOH concentrations, the heat treating times, and the heating temperatures. The resulting mechanical properties of the fabrics also studied. The samples used were Nylon/Co-PET sea-island type composite microfiber (Co-PET content: 35%) non-woven fabric. The conclusions obtained were as follows. 1. For the complete extraction of Co-PET from the sample non-woven fabric in the dry hot air process, $160^{\circ}C$ of air temperature, 15 min. of treatment time, and around 30% of NaOH concentration were required. On the other hand, in the wet hot air process, $140^{\circ}C$ of air temperature, 3.5 min. of treatment time, and around 30% of NaOH concentration were required. 2. The mechanical properties of the continuous processed samples showed that the WT, B, and WC increased with increasing the weight reduction ratio. However, the G, decreased with increasing the weight loss ratio. Note that, particularly in B, it increased drastically when the weight deduction ratios exceeded 30%. 3. As increasing the wet hot air temperature from 130 to $140^{\circ}C$, B appeared to increase, however, WT, G, and WC appeared to decrease. 4. The best condition found in this continuous process to extract Co-PET is the wet hot air temperature of 140, NaOH concentration of 28% or above, and the treatment time 2-4 min.

• Journal of Korean Society on Water Environment
• /
• v.25 no.3
• /
• pp.452-458
• /
• 2009

This study was carried out to assess the effect of discharge loading at sewage treatment plants (STP) on water quality in Kyoungan stream. The seasonal variations of water quality (BOD, COD, SS, TN, and chl.a) at site 1(Mesanribo) were similar with those at site 2(Sehabo). BOD, COD, SS, and chl.a concentration were also similar except for TN and TP concentration which were lower than those at site 1. The BOD, COD, TN, TP and chl.a concentration at site 2 in dry period were higher than that of wet period. The ratios of BOD, TP, COD, SS discharge loading at all STP in Kyoungan stream watershed to delivery loading at site 2 were 0.69, 0.54, 0.48, 0.31, and 0.26 on average, respectively. Both site 1 and site 2, the seasonal variations of discharge loading at STP did not showed any relationship with those of water quality. The mean ratios of inflow loading at site 1 to delivery loading at site 2 were relatively high that ranged from 0.43 to 0.61. In dry period, the ratios of discharge loading at STP in Sehabo watershed to delivery loading at site 2 were below 0.2 except for BOD (0.24), and decreased <0.1 in wet period. While, SS loading from watershed between site 1 and site 2 to delivery loading at site 2 ratios increased in wet period.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.18 no.4
• /
• pp.195-202
• /
• 2005

Purpose　：　The purpose of this study is to report clinical management of acute　dermatitis patient during the period of pregnancy by oriental medicine.　Methods : Generally acute dermatitis is treated by corticosteroids, antibiotics,　antihistamines ec. But the use of these drugs may affect pregnancy women　adversely. So we think that oriental medical therapy is useful to treat a pregnancy　women who has acute dermatitis. We experienced a case of acute dermatitis patient　during the period of pregnancy. In the beginning of treatment, she has severe　itching, burning sensation, bulla, papule. We treated her with herbal medicine and normal saline wet dressing. Results : After treatment during 10days(admission treatment-herb medication, normal saline wet dressing), her symptoms was improved fairly After that she took herb medicine for a month, and all of her symptoms was disappeared. So she was satisfied with the result. Conclusion : Dermatosis gravidarum is a pregnancy-associated disease, which include itching, papule, eczema ec. It is generally due to blood deficiency(血虛)　under pregnancy condition. So samooltang is effective on dermatitis under blood deficiency.

• Elastomers and Composites
• /
• v.55 no.1
• /
• pp.26-39
• /
• 2020

The physical properties of silica-filled SBR compounds (WSBR) prepared using silica-SBR wet masterbatches (WMB) were systematically investigated to understand the effect of the surface treatment of silica on the reinforcement performance of SBR. Treatment of silica with bis(triethoxysilylpropyl)tetrasulfide (TESPT) in the liquid phase, followed by mixing with an SBR solution and recovery by water stripping, easily produced silica-SBR WMB. However, insufficient surface treatment in terms of the amount and stability of the incorporated TESPT led to considerable silica loss and inevitable TESPT elution. Pretreatment of silica in the gas phase with TESPT and another organic material that enabled the formation of organic networks among the silica particles on the surface provided hydrophobated silica, which could be used to produce silica-SBR WMB, in high yields of above 99%. The amount and type of organic material incorporated into silica greatly influenced the cure characteristics, processability, and tensile and dynamic properties of the WSBR compounds. The TESPT and organic material stably incorporated into silica increased their viscosity, while the organic networks dispersed on the silica surface were highly beneficial for reducing their rolling resistance. Excessive dosing of TESTP induced low viscosity and a high modulus. The presence of connection bonds formed by the reaction of glycidyloxy groups with amine groups on the silica surface resulted in physical entanglement of the rubber chains with the bonds in the WSBR compounds, leading to low rolling resistance without sacrificing the mechanical properties. Mixing of the hydrophobated silica with a rubber solution in the liquid phase improved the silica dispersion of WSBR compounds, as confirmed by their low Payne effect, and preservation of the low modulus enhanced the degree of entanglement.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2000.10a
• /
• pp.563-568
• /
• 2000

Animal waste is a major agricultural waste or wastewater that requires appropriate treatment to prevent environmental pollution. In this presentation, it is examined if incineration of manure compost is an alternative to treatment of animal waste. Heating values of selected biomass including manure compost were obtained using a bomb calorimeter. Based on heating values of manure and manure compost, ranging from 1200 - 1500 kcal/kg on wet base, incineration could be an alternative for animal waste treatment if available land is limited for land application and sufficient reduction of water content in manure compost.