• Journal of the Korean Wood Science and Technology
• /
• 제31권2호
• /
• pp.77-83
• /
• 2003

본 연구에서는 대나무 Zephyr 보드에 있어서 열압조건이 보드의 성능에 미치는 영향을 조사하기 위하여 다양한 열압시간과 열압온도를 적용하여 보드(목표밀도 0.7 g/cm³, 400×400×12 mm)를 제조하고 그 기본적인 물성을 비교, 검토해 보았다. 제조된 보드는 KS F 3104와 KS F 3113에 준하여 성능평가를 하였으며 그 결과는 다음과 같다. 보드의 상태 휨강도는 열압조건에 관계없이 전반적으로 상당히 높은 값을 나타내었으며 그 중 span에 대한 평행 방향에 있어서는 열판온도 160℃에서 12분 동안 열압하여 제조한 보드가 가장 높은 강도를 보였다. 보드의 박리강도 시험에서는 모든 열압시간에서 열압온도가 높을수록 상대적으로 더 높은 값을 나타내었으며, 그 결과 200℃에서 압체된 보드가 가장 높은 강도를 보였다. 보드의 습윤 휨강도 시험에서는 총 열압시간 12분과 10분일 때 각각 160℃와 180℃의 온도에서 제조된 보드가 상대적으로 높은 강도를 나타내었다. 더욱이, 200℃에서 8분 동안 열압하여 제조한 보드의 경우 상태 휨강도에 거의 육박하는 가장 높은 습윤 휨강도를 보였다. 두께 팽창율 시험에서는 모든 보드에서 전반적으로 6% 미만의 낮은 값을 나타내어 높은 치수안정성을 가지는 것을 알 수 있었다.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제43권1호
• /
• pp.22-28
• /
• 2021

Natural nonwoven silk fabric has attracted researchers' attention owing to its unique properties as a biomaterial. It is fabricated by reeling, wetting, and hot pressing natural silk filament from silkworm cocoons. In this study, silkworm cocoons were immersed in water at different temperatures for various durations to examine the effects of wet treatment on their crystallinity and morphology. As the treatment temperature and time increased, the cocoon's silk filament separation became more evident, and fibroin strands were observed in it. The crystallinity indexes of the silkworm cocoons increased until a treatment time of 2 h and remained constant thereafter. The increase in the crystallinity index using wet treatment was enhanced by increasing the treatment temperature. Although the weight loss of the silkworm cocoon was insignificant until 40℃, it was appreciable above this temperature, and the degree of weight loss constantly increased with increases in the treatment temperature and time.

• 펄프종이기술
• /
• 제38권1호통권113호
• /
• pp.54-61
• /
• 2006

Basically corrugated board is composed of three layers of different basis weight and stock composition. Warp is well-known for one of the most important problems of corrugated board production. Warp is caused by difference of hygro-expansibility of linears between top and bottom. This research was performed to evaluate the effect of paper properties on the warp of corrugated board. To evaluate warp, dynamic expansion properties of paper was tested using DPM(dynamic penetration measuring system). The effects of sizing, stock composition and wet-pressing on dynamic expansion properties were also evaluated. Commercial base papers showed different dynamic expansion property depending on stock composition and papermaking operation. Sizing treatment decreased and wet-pressing increased the amount of dynamic expansion. To reduce warp of corrugated board, management of dynamic expansion of base papers should be controlled by manipulating moisture, heat and tension, using a variety of adjustments available on the corrugator.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.423-426
• /
• 2006

Paper has fibers and fines network structure and it is strongly affected by interface bonding between fibers. Depending on the inter-fiber bonding, paper bulk is determined. Fines play an important roll in Campbell and consolidation effect through wet pressing and drying operations. Refined Sw-BKP, Hw-BKP and BCTMP fines were used to investigate the fines effect. Wet-web strength, breaking length, scattering coefficient, and hydrodynamic specific volume were measured. According to the result of experiments, chemical and morphological compositions of fines do not strongly affect to wet-web forming, but strongly affect to drying operations which form hydrogen bonding among fiber-fines-fiber matrixes. Paper bulk should be controlled by the extent of hydrogen bonding between fibers during drying operations.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.181-190
• /
• 2006

This study was conducted to develop dry forming technology and evaluate the properties of dry formed paper made from Hw-BKP. A dry forming mold (DFM) was developed to observe the phenomena of dry forming and evaluate the properties of formed papers. To upgrade the DFM a dry forming system (DFS) was developed. This DFS was designed to improve the formation of dry formed papers and enhance the productivity of dry forming. Dry forming gave papers with greater bulk and opacity than wet forming. Tensile strength of dry formed paper was greater than that of conventional wet formed handsheet when they were made from the same dry disintegrated fibers. But tensile strength of conventional wet formed handsheet made from beaten fiber was much greater than that of dry formed paper made from dry disintegrated fibers. When solvent dried beaten fibers were used in dry forming, the tensile strength of dry formed papers reached 73.5% of the wet formed handsheets made from beaten fiber. It showed that dry forming has a significant potential in improving strength properties when proper preparation of fibers and appropriate humidification, pressing, and drying processes are employed.

• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• 펄프종이기술
• /
• 제41권1호
• /
• pp.9-16
• /
• 2009

Cylindrical dry forming mould was developed to carry out a feasibility study of dry forming of papers. The effect of disintegration, forming, humidification and pressing on dry formed papers was examined. Dry disintegrated fibers showed the similar fiber length distribution to wet disintegrated fibers, but they showed distorsion and damaged appearance on the surface. Process parameters required to form a uniform fiber pad was investigated. A proper screening and air dispersion method was selected that gives proper formation. Humidification and pressing conditions were examined to get a good dry formed papers in dry forming. Results showed that dry forming method can be used to make a sheets with reasonable formation and properties.

• Journal of the Korean Wood Science and Technology
• /
• 제23권3호
• /
• pp.33-39
• /
• 1995

To accelerate the cure of phenolic resin adhesives for plywood, the complexation with melamine resin and the addition of cure-accelerating agents were discussed. The hot-pressing temperature and time of phenol resin could be decreased by complexation with melamine resin. but the wet glue-joints strength of phenol melamine resin was lower than that of ordinary phenol resin in case of plywood using spruce veneer at core layer. Among the tested cure-accelerating agents. the sodium carbonate showed the greatest effect on shortening gelation time of phenolic resin. In addition, in the manufacturing scale test, the hot-pressing time of phenol resin with the addition of 5 parts sodium carbonate could be shortened about 20% compared with ordinary phenol resin which had same glue-joints properties.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2011년도 추계학술발표회 논문집
• /
• pp.433-442
• /
• 2011

• 한국세라믹학회지
• /
• 제35권4호
• /
• pp.371-377
• /
• 1998

HAC/PVA계 MDF 시멘트 복합재료의 수분안정성을 향상시키기 위하여 수용성 epoxy resm을 시멘트 중량에 대해 5wt% 에서 15wt%까지 첨가하고 calendering법, extruding법, warm pressing법으로 성형하여 epoxy resin첨가량 및 제조공정이 수분안정성에 미치는 영향을 살펴보았다. 제조된 시편은 건조상태 및 3일, 7일, 14일간 물 속에 침적 후 습윤강도를 3점 곡강도로 측정하고 SEM으로 표면 가까운 부분의 파단면을 관찰하고 수은압입법으로 기공분포 및 기공율을 분석하여 침수 재령벌 MDF 시멘트 복합재료의 미세조직 변화를 살펴보았다. 적량의 epoxy resin 첨가에 의해 건조강도는 감소하였으나 전반적으로 수분안정성이 향상되었다. 그러나 전반적으로 epoxy의 함량이 많아지면 초기건조강도는 감소하는 경향을 나타나었으며 epoxy 첨가량이 7wt% 이상일 경우에서는 수분안정성 역시 별다른 효과를 볼 수 없었다. 제조공정별로는 warm pressing법에 의해 성형된 경우 epoxy 첨가에 의한 강도 및 수분안정성 향상 효율이 다른 방법보다 월등히 뛰어났으며 epoxy resinmdmf 5wt%, 7wt% 첨가하였을 때, 최적의 강도 및 수분안정성 효과를 얻을 수 있었다.