• 설비공학논문집
• /
• 제2권2호
• /
• pp.137-141
• /
• 1990

When the relative humidity is measured with an aspirated psychrometer, three factors, which affect the measurement of relative humidity, are atmospheric pressure, the size of wet element and the wind velocity. This paper investigated the effects of the above three factors, and the computer code was developed in order to enhance the accuracy of the relative humidity measurement. As results, it is found that the relative humidity decreases by 6%RH with increasing atmospheric pressure from 650 mbar to 1100 mbar. It is found that the relative humidity drops down when the size of the wet element increases, though the effect of the size of the wet element is not significant. Finally, relative humidity increases with the increasing wind velocity. The difference between the psychrometic table in the present KS and the present results is about 2%RH maximum. As a conclusion, the three factors mentioned above should be considered in order to secure accurate measurement of relative humidity.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제7권10호
• /
• pp.2527-2543
• /
• 2013

A novel steganographic QR code algorithm, which not only coveys the secret into the widely-used QR barcode but also preserves the readability of QR content and the capability of error correction, is presented in this article. Different from the conventional applications for QR barcode, the designed algorithm conceals the secret into the QR modules directly by exploiting the error correction capability. General browsers can read the QR content from the QR code via barcode readers; however, only the authorized receiver can further reveal the secret from the QR code directly. The new mechanism can convey a larger secret payload along with adjustment of the QR version and error correction level. Moreover, the blind property allows the receiver to reveal the secret without the knowledge of the embedded position of modules. Experimental results demonstrate that the new algorithm is secure, efficient and feasible for the low-power QR readers and mobile devices.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.2-5
• /
• 2011

This paper presents a numerical study on multiphase flows induced by wall adhesion The CSF(Continuum Surface Force} model is used for the calculation of the surface tension force and implemented in an in-house solution code(PowerCFD). The present method(code) employs an unstructured cell-centered method based on a conservative pressure-based finite-volume method with volume capturing method(CICSAM) in a volume of fluid(VOF) scheme for phase interface capturing As an application of the present method, the effects of wall adhesion are numerically simulated with the CSF model for a shallow pool of water located at the bottom of a cylindrical tank. Two different cases are computed, one in which the water wets the wall and one in which the water does not wet the wall. It is found that the present method simulates efficiently and accurately surface tension-dominant multiphase flows induced by wall adhesion.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2004년도 춘계학술발표논문집
• /
• pp.127-139
• /
• 2004

The process of papermaking involves water removal on the paper machine wire, in the press section and in the dryer section. In the dryer section, liquid water in the wet web is removed mainly by evaporation. In conventional machine this is achieved by passing the web over a number of steam heated dryer rolls. A drying process of paper on a heated cylinder roll calculated based on a 1-dimensional model which concerns unsteady heat and mass transfer in the direction of paper thickness. In this study, Prediction of moisture contents average paper sheet temperature and volume fraction along a series of cylinder. Independently, developed models is compared using the same reference data. The model is implemented in CFD code, FLUENT, using user-define-function(UDFs).

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2005년도 Proceedings of ISRS 2005
• /
• pp.415-417
• /
• 2005

In order to retrieve the latent and sensible heat fluxes, high-resolution airborne imageries with visible, near infrared, and thermal infrared bands and ground-base meteorology measurements are utilized in this paper. The retrieval scheme is based on the balance of surface energy budget and momentum equations. There are three basic surface parameters including surface albedo $(\alpha)$, normalized difference vegetation index (NOVI) and surface kinetic temperature (TO). Lowtran 7 code is used to correct the atmosphere effect. The imageries were taken on 28 April and 5 May 2003. From the scattering plot of data set, we observed the extreme dry and wet pixels to derive the fitting of dry and wet controlled lines, respectively. Then the sensible heat and latent heat fluxes are derived from through a partitioning factor A. The retrieved latent and sensible heat fluxes are compared with in situ measurements, including eddy correlation and porometer measurements. It is shown that the retrieved fluxes from our scheme match with the measurements better than those derived from the S-SEBI model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 제40회 하계학술대회
• /
• pp.1497_1498
• /
• 2009

This paper presents the simulation of micro-lens arrays based on dry and wet etching technique. Code V (Optical Research Associates Ltd) simulation was performed to extract optimal design parameters of a Micro-Lens Array(MLA). Thickness of UV adhesive, wavelength of laser source, curvature, and shape of lens surface were chosen for the design parameters. The simulation results showed that focal length of a MLA decreased with the increase of UV adhesive thickness. And the focal length depended on shape of lens surface and length of laser source.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2631-2636
• /
• 2008

The most components and piping of the secondary side of domestic nuclear power plants were manufactured carbon-steel and low-alloy steel. Flow accelerated corrosion leads to wall thinning (metal loss) of carbon steel components and piping exposed to the flowing water or wet steam of high temperature, pressure, and velocity. The feedwater heaters of many nuclear power plants have recently experienced sever wall thinning damage, which increases as operating time progress. Several nuclear power plants in Korea have also experienced wall thinning damage in the shell wall around the impingement baffle. This paper describes the comparisons between the numerical analysis results using the FLUENT code and the experimental results based on down-scaled experimental facility. The experiments were performed based on several types of impingement baffle plates which are installed in low pressure feedwater heater.

• 대한기계학회논문집B
• /
• 제36권7호
• /
• pp.721-730
• /
• 2012

본 연구에서는 벽면부착에 의해 야기되는 다상유동에 대한 수치적 연구를 제시한다. 먼저 다상유동 해석을 위해 표면장력에 대한 CSF(Continuum Surface Force) 모델 및 벽면부착 경계조건 모델을 비정렬격자계에 적합하도록 수치해석방법을 정립시키고, Myong(2009)이 개발한 비정렬격자계와 VOF 방법으로 체적포착법(volume capturing method)을 사용한 수치해석방법(코드)에 삽입하였다. 또한 본 수치해석방법을 사용하여 중력을 포함하여 어떤 외력도 존재하지 않고 오직 벽면부착에 의해 야기되는 유동현상인 원통형 탱크의 바닥에 위치한 얕은 물풀(water pool)에 대해 물이 벽면을 적시는 경우와 적시지 않는 경우에 대해 수치해석 하였다. 연구결과, 본 수치해석방법은 벽면부착에 의해 야기되는 다상유동 문제에 대한 유용성이 입증되었다.

• Computers and Concrete
• /
• 제13권1호
• /
• pp.135-147
• /
• 2014

Strut-and-tie model (STM) has been recommended by many codes and standards as a rational model for discontinuity regions in structural members. STM has been adopted in ACI building code for analysis of reinforced concrete (RC) deep beams since 2002. However, STM recommended by ACI 318-11 is only applicable for analysis of ordinary RC deep beams. This paper aims to develop the STM for CFRP strengthened RC deep beams through the strut effectiveness factor recommended by ACI 318-11. Two sets of RC deep beams were cast and tested in this research. Each set consisted of six simply-supported specimens loaded in four-point bending. The first set had no CFRP strengthening while the second was strengthened by means of CFRP sheets using two-side wet lay-up system. Each set consisted of six RC deep beams with shear span to effective depth ratio of 0.75, 1.00, 1.25, 1.50, 1.75, and 2.00.The value of strut effectiveness factor recommended by ACI 318-11 is modified using a proposed empirical relationship in this research. The empirical relationship is established based on shear span to effective depth ratio.