• Environmental Analysis Health and Toxicology
• /
• 제15권1_2호
• /
• pp.39-43
• /
• 2000

Linear alkyl sulfonates (LAS) constitute a large fraction of the surfactants used in cleaning processes in households, trade and industry Despite the industrial significance and the possible environmental impact of these compounds, the fast and inexpensive determination of LAS concentrations is still a difficult task. In this study, near infrared (NIR) spectroscopy which is a rapid spectroscopic analysis method compared with a traditional analytical method for the measurement of LAS concentration such as HPLC, GC and standard wet chemistry method. NIR spectra of LAS between 0.313 and 25.0% (w/v) in water were utilized to develop a calibration model. The best results (R ＝ 0.998, SEP ＝ 0.244% (w/v)) obtained by using partial least-squares regression with spectral data treatment and 2nd derivatization were comparable to the results (SEC ＝ 0.186% (w/v), SEP ＝ 0.206% (w/v)) obtained by using multiple linear least-squares regression (MLR). However, models based on derivative spectra have no significant advantage with MLR.

• Transactions on Electrical and Electronic Materials
• /
• 제1권1호
• /
• pp.6-11
• /
• 2000

The hydrogen plasma treatment of silicon wafers in the reactive ion-etching mode was studied for the application to silicon-on-insulator wafers which were prepared using the wafer bonding technique. The chemical reactions of hydrogen plasma with surface were used for both surface activation and removal of surface contaminants. As a result of exposure of silicon wafers to the plasma, an active oxide layer was found on the surface. This layer was rendered hydrophilic. The surface roughness and morphology were examined as functions of the plasma exposing time and power. In addition, the surface became smoother with the shorter plasma exposing time and power. The value of initial surface energy estimated by the crack propagation method was 506 mJ/㎡, which was up to about three times higher as compared to the case of conventional direct using the wet RCA cleaning method.

• Progress in Superconductivity
• /
• 제3권2호
• /
• pp.146-150
• /
• 2002

We performed the point contact spectroscopy on newly discovered superconductor $MgB_2$ thin films with Au tip. In the point contact spectroscopy of the metallic Sharvin limit, the differential conductance below the gap is twice as that above the gap by virtue of Andreev Reflection. After some surface cleaning processes of sample preparation such as ion-milling and wet etching, the obtained dI/dV versus voltage curves are relatively well fitted to the Blonder-Tinkham-Klapwijk (BTK) formalism. Gaps determined by this technique were distributed in the range of 3meV~ 8meV with the BCS value of 5.9meV in the weak coupling limit. We attribute these discrepancies to the symmetry of the gap parameter and the degradation of the surface of the sample. We also present the temperature dependence of the conductance vs voltage curve and thereby the temperature dependence of the gap.

• 패션비즈니스
• /
• 제15권4호
• /
• pp.182-189
• /
• 2011

Dyeing properties of cow leather was investigated with Tumeric powder. The effects of dyeing conditions, mordanting conditions, color change, and color fastnesses were studied. The results were as follows. The dye uptake increased as dye concentration, dyeing temperature, and bath ratio increased. In the effect of dyeing time, the highest dye uptakes showed at 20 minutes and decreased after that point. Pre mordanting was more effective than the post mordanting, and the dye uptakes improved all mordanted fabrics. The highest K/S values showed in pre-Al sample, and the lowest K/S values showed in post-Cu one. The values of Hunter on the samples were more changeable $L^*$ and $b^*$ than $a^*$, and all samples showed Yellow color in Munsell value. But the mordanting methods and mordanting agents were not significant in the color changes. The light fastness of dyed samples showed 1 grade, the dry cleaning and abrasion fastnesses did not improved except post-Fe wet sample.

• 대한안전경영과학회지
• /
• 제18권3호
• /
• pp.81-89
• /
• 2016

Floor slipperiness is a leading cause in slip and fall accidents which are a major source of occupational injuries in Korea. Researchers have estimated the slip and fall related accidents rank number one or two in number of the injured. The objectives of this study were to find the field contamination effect and improvement countermeasure. Slipping and falling are common accidents in large public facilities, especially facility which vulnerable adults generally use as like hospital. So, we measured the coefficient of friction of several floors on the floor in hospital, under dry and wet using BOT-3000. The results of the coefficient of friction measurements showed that floor type and surface conditions were all significant factors affecting the coefficient of friction. The most surprising finding of this study was that there were significant friction improvement when the floors were properly cleaned with cleaning equipments.

• 대한가정학회지
• /
• 제34권5호
• /
• pp.41-48
• /
• 1996

The purpose of this paper was to identify bonding strength by laundering methods(dry and wet) of the after laundering of the adhesive interlining. The results of this study were as fallows. 1.As laundery repeated it revealed that the bonding strength was decreased to some degree regardless of the kinds of face cloth, laundering methods & adhesive interlining. 2. Bonding strength of woven adhesive interlining after and before ironing is different by its weave: A1>A3>A2. 3. Bonding strength before cleaing is smaller than that after laundering with ironing. 4. As for laundering methods, while dry cleaning is excellent with little influence on bonding strength. It doesn't deform the shapes of dress, in cases of woven adhesive interlining.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1305-1306
• /
• 2007

To lower the fabrication cost of silicon solar cells, a surface treatment using a dielectric barrier discharge instead of a wet cleaning technique was examined on electrode surfaces on silicon solar cells. The fill factor obtained through measuring current-voltage characteristics was evaluated, and the treated surface state was characterized by energy-dispersive X-ray. It was found that the dielectric barrier discharge effectively activated the electrode surface and the surface treatment on finger electrodes contributed greatly to improve the fill factor.

• Journal of Periodontal and Implant Science
• /
• 제31권2호
• /
• pp.451-463
• /
• 2001

Following the extensive use of implant, the incidence of peri-implantitis increases. Guided bone regeneration has been used for the optimal treatment of this disease. Because implant surface was contaminated with plaque and calculus, cleaning and detoxification were needed for the reosseointegration when guided bone regeneration was performed. Various mechanical and chemical methods have been used for cleaning and detoxification of implant surface, air-powder abrasive and oversaturated citrate were known to be most effective among these methods. However, these methods were incomplete because these could not thoroughly remove bacteria of implant surface, moreover deformed implant surface. Recent studies for detoxification of the implant surface using laser were going on, $CO_2$ laser and Soft Diode laser were known to be effective among these methods. The purpose of this study was to obtain clinical guide by application these laser to implant surface. 15 experimental machined pure titanium cylinder models were fabricated. The $CO_2$ laser treatment under dry, wet and hydrogen peroxide condition or the Soft Diode laser treatment under Toluidine blue O solution condition was performed on the each of models. Each groups were examined with SPM and SEM to know whether their surface was changed. The results were as follows : 1. Surface roughness and surface form weren't changed when $CO_2$ laser was usedunder dry condition(P>0.05). 2. Surface roughness and surface form weren't changed when $CO_2$ laser was used under wet condition(P>0.05). 3. Surface roughness and surface form weren't changed when $CO_2$ laser was used under hydrogen peroxide condition(P>0.05). 4. Surface roughness and surface form weren't changed when Soft Diode laser was used under toluidine blue O solution condition(P>0.05). From the result of this study, it may be concluded that the $CO_2$ laser having relatively safe pulse mode and the Soft Diode laser used with photosensitizer can be used safely to treat peri-implantitis.

• 대한환경공학회지
• /
• 제22권1호
• /
• pp.21-31
• /
• 2000

본 연구에서는 공기청정기, 기수분리기 및 중성능 필터로 구성되는 습식 공기청정장치를 대상으로 입자와 유해가스인 $SO_2$, NO, $NO_2$, HCHO 및 $NH_3$의 제거 특성을 실험적으로 살펴보고, 실험결과를 대상물질의 물리화학적 특성과 연관시켜 검토하였다. 입자제거 실험에서는 대기 에어로졸을 송풍기를 통해 장치에 도입하여 장치의 3곳에서 2대의 레이저 입자계수기로 입자크기 분포를 측정하여 각 구성요소의 입자제거효율을 구하였다. 실험결과로부터 기수분리기에서는 입경이 $5{\mu}m$ 이상인 조대 입자가 주로 제거되고. 중성능 필터에서는 이보다 작은 미세 입자가 주로 제거됨을 알 수 있었다. 유해가스 제거 실험에서는 시험용 가스를 송풍기의 출구에 주입하여 공기청정기의 상류와 기수분리기의 하류에서 가스농도를 측정하여 유해가스 제거효율을 구하였다. 실험결과로부터 헨리상수가 큰 수용성인 $SO_2$, HCHO 및 $NH_3$는 제거효율이 높았으나, 헨리상수가 낮아 난용성인 NO와 $NO_2$는 제거효율이 낮음을 알 수 있었으며, 공기청정기에서 상당량의 음이온이 발생됨을 알았다.

• 한국응용과학기술학회지
• /
• 제34권1호
• /
• pp.58-65
• /
• 2017

유동층가스화기는 경제적으로 기술적으로 입증된 기술로서 가장 상용화에 가까운 가능성을 보여주고 있다. 그러나 한국에서는 설계, 현장문제 해결뿐 아니라 파일럿 규모의 설비 운전 등이 부족하여 상용화에 이르지 못하고 있다. 본 연구에서는 바이오매스의 가스화를 위하여 3 MWth 급 순환유동층(CFB) 반응기를 개발하여 운전하였다. 유동층반응기는 순환유동층 반응기와 기포유동층 반응기로 구성되었으며 타르와 산성가스를 제거하기 위하여 세라믹필터, 급속냉각, 습식스크러버를 사용하였다. 3MWth 급 바이오매스 가스화기의 최적 운전조건을 도출하기 위하여 equivalence ratio에 따른 영향을 조사하였다