• 비파괴검사학회지
• /
• 제32권2호
• /
• pp.149-154
• /
• 2012

용접구조물에는 외력이 부가되기 이전에 잔류응력이 걸려 있으므로 용접잔류응력 크기 및 분포 상태는 취성파괴, 피로강도, 응력부식균열, 좌굴, 시효변형과 같은 다양한 형태의 손상에 직접적으로 영향을 끼쳐 잔류응력을 정량적으로 해석하기 위한 지속적인 연구가 필요한 실정이다. 본 논문은 비파괴적인 기법 중 레이저를 이용한 전자처리스페클패턴 간섭법을 이용하여 평판 용접시험편의 외부하중에 따른 전체 거동에 잔류응력의 측정 기법을 제시하고자 한다. 용접시험편에 인장 하중을 가하였을 때, 이를 전자처리패턴스페클 기법을 이용하여 측정하였다. 측정된 결과로부터 용접시험편의 모재부와 용접부의 변형률을 측정하고, 이를 이용하여 탄성계수를 측정하였다. 본 논문은 전자처리스페클패턴 간섭법으로 용접시험편의 용접부와 모재부의 변형률의 차이를 이용하여 잔류응력 값을 산출하는 식을 제시하였고, 이를 수치적으로 계산하여 잔류응력 값을 산출하였으며 측정 결과, 모재부에 비해 용접부의 탄성계수가 약 3.7배 높은 약 8.46 MPa로 측정되었다.

• 한국압력기기공학회 논문집
• /
• 제11권1호
• /
• pp.45-52
• /
• 2015

Even though a lot of efforts have been devoted to evaluate welding residual stress characteristics of nuclear components, from the view point of accuracy, there are still some arguments in application of engineering estimation schemes. In this paper, three-dimensional finite element analyses (FEA) were carried out to predict residual stress distributions in butt welds of a typical surge line piping. Mesh optimization was conducted and subsequent analysis results such as the axial and hoop stress components along the weld center line and inner wall. Moreover, alternative evaluation was conducted by using three representative equations and their results were compared to those of FEA. Thereby, key parameters affecting to temperature profiles and residual stress distributions were derived as well as an optimum engineering estimation scheme was recommended.

• Journal of Welding and Joining
• /
• 제21권6호
• /
• pp.71-76
• /
• 2003

For the purpose of clarifying the influence of welding residual stress to the fatigue crack propagations behaviour, an analytical investigation based on finite element method is performed to examine the opening behaviour of tip-closed crack in the compressive residual stress. A finite element model comprised of contact elements for the crack plane and plane stress elements for the base material is used to evaluate crack opening stress of the crack existing in the residual stress field. Also an analytical method based on the superposition principle to estimate the length of opened part of tip closed crack and the stress distribution adjacent to the crack during uploading is applied to the finite element model. The software for the analysis is ABAQUS, which is a general purpose finite element package. The results show that stresses distributed on the crack surfaces are reduced and approached to zero as the applied stresses are increased up to crack tip opening stress and no mechanical discontinuity is found at the boundary of contact elements and plane stress elements. It is verified that the opening behavior of the fatigue crack in the residual stress can be predicted by finite element method with the proposed analytical method.

• 대한기계학회논문집A
• /
• 제30권7호
• /
• pp.826-832
• /
• 2006

For the improvement of safety and endurance in welded steel structure, it is needed to consider welding residual stress distribution and rolling directional characteristics of materials. In this study, it was investigated experimentally about characteristics of fatigue crack propagation according to welding residual stress and rolling in FCAW(flux cored arc welding) butt-jointed steel plates. SS400 steel plates of 3mm thickness were selected and tested for this study. When the angles between tensile loading direction and rolling direction in welded materials are increased from $0^{\circ}\;to\;90^{\circ}$, their fatigue crack propagation rates are increased. These results are same as predicted increments of fatigue crack propagation rate when stress ratio is increased from 0 to 0.5. When the angles of rolling direction and welding direction to tensile loading direction are $0^{\circ}\;and\;90^{\circ}$ respectively, fatigue crack propagation rate in welded material is lowest.

• Journal of Welding and Joining
• /
• 제21권5호
• /
• pp.561-567
• /
• 2003

For construction of I-beam steel structures, a fillet welding is one of the main manufacturing process. However, this welding process cause some problems associated with welding residual stress and welding deformation that are harmful to the safety of structures. Accordingly, this study clarified the creation mechanism of the welding deformation on I-beam steel structure from the experimental results given by the FEM method. To prevent or minimize the longitudinal bending deformation, first of all, a field supervision is necessary to observe the optimal groove design. Secondly, the welding order for cooling weld zone is needed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.58-60
• /
• 2004

In the field of welding the behavior of a welded structure under consideration may be predicted via heat transfer and residual stress analysis. In order to facilitate the industrial applications of welding, numerical modeling of heat transfer and residual stress in weldment has been carried out applying Finite Element Method (FEM) and the analysis with the external load including this residual stress due to welding has been done. The present work includes the specialized finite element codes for the calculation of nonlinear heat transfer details and residual stress redistributed along with the external load in the welded structures. A basic interface, which allows models, built in commercial preprocessing package access to the data necessary to build standard input decks for these specialized FEM codes, which are not supported by commercial package. The results from the FEM codes are imported back into commercial package for visualization. In addition the residual stress values are exported to commercial package (such as ANSYS, PATRAN etc.) for further analysis with the external loads, which make the FEM codes fully applicable to the industrial purpose.

• Journal of Welding and Joining
• /
• 제7권4호
• /
• pp.46-55
• /
• 1989

Zirconia coatings are performed by the plasma spraying on the substrate of Al-Si alloy. In case of plasma sprayed ceramic coatings, it is important to control properly residual stress occurred during cooling process. Residual stress in coating layer varies with sprayed conditions and is influenced greatly by the coating layer thickness. Surface residual stress due to coating layer thickness is measured by X-ray diffraction method and the residual stress in coating layer is estimated by the deflection of coating layer when the restraint force in substrate was removed. When zirconia was coated on the substrate, tensile residual stress remains on zirconia coated surface layer. The tensile stress is increased to 0.35mm thickness and after 0.45mm thickness it is decreased abrouptly. A thick bond and composite coating reduce the zirconia surface stress and composite coating controls effectively the thick zirconia surface stress.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.372-377
• /
• 2002

Residual stress by welding should be reduced because that decreases the reliability on strength of welded structure. The reason is that the total stiffness of structure decreases by non-linear behavior of weldment under external load. The release of residual stress by mechanical loading and unloading is often performed in the fabrication of box structure for steel bridge. The proper degree of loading and unloading is significant at release method of residual stress by mechanical loading because that degree is changed by material and geometric shape of welded structure. Therefore, the simulation model that could exactly analyze the release of residual stress by mechanical loading is to be necessary. This simulation model should be established on the based of variable and accurate measurement data. In this study, the non-linear behavior of weldments under external loading and unloading, such as the decrease and increase of structure stiffness, was investigated by monitoring of nominal stress and strain. Tensile loading and unloading test under variable load was performed and the proper degree of stress relaxation was measured by sectioning technique using strain gauge.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.187-193
• /
• 1997

In the weldmentsm the crack propagation rate is changed due to the residual stress. The crack propagation rate is high in the region with the residual stress. However it shows rhw same behavior with the base metal in the region that does not include the residual stress. The fatigue crack growth rate for the material with residual stresses can be predicted more precisely by using the effective stress ratio. The difference between experimental results and prediction results in the initial stage seems to be due to the redistribution of residual stresses and microstructural change.

• 한국강구조학회 논문집
• /
• 제13권4호
• /
• pp.327-335
• /
• 2001

강관 적층용접부에서 발생하는 잔류응력의 특징과 생성 메커니즘을 밝히기 위해 유한요소법을 이용한 3차원 열탄소성 해석을 수행하였다. 용접에 의해 강관을 접합할 때, 원주방향잔류응력과 두께방향잔류응력은 강관 내 외부에서 모두 접합부에서 인장응력이 발생하고, 길이방향잔류응력은 강관 내무에서 인장응력, 외부에서 압축응력이 발생된다. 또한 강관 적층 용접부의 잔류응력 생성기구를 명확히 하였다. 그 결과, 강관의 용접에 의한 잔류응력은 열응력에 의해 발생 할 뿐만 아니라, 강관의 기하학적 형상변화에 의한 영향도 받는다는 것을 밝혔다. 그리고, 용접조건과 강관의 제원이 달라질 경우에도 잔류응력 생성기구가 변함이 없음을 밝혔다.