• 한국정밀공학회지
• /
• 제30권8호
• /
• pp.815-823
• /
• 2013

The hot curvature forming of large aluminum plates is a process used to produce spherical liquefied natural gas (LNG) tanks. In this study, we describe a method to determine the optimum shape of blanks to minimize the root gap in the forming process. The method proposed in this study was applied to a small-scale model for thick plates with a curvature of 1500 mm and thickness of 6 mm. First, the shape of the curved shells was determined as the target shape, and then a coordinate transform was used to determine the optimum blank shape, which was then iteratively modified using the results of finite element method (FEM) simulations, including heat transfer, until the shape error was minimized. Experiments in forming using Al5083 thick plate were carried out, showing that the method can determine the optimum blank shape within an allowable root gap of 0.1 mm.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.200-213
• /
• 2000

Lasers have given dentistry a new rapid, economic, and accurate technique for metal joining. Although laser welding has been recommended as an accurate technique, there are some limitations with this technique. For example, the two joining surfaces must have a tight-fitting contact, which may be difficult to achieve in some situations. The tensile samples used for this study were made from a custom-made pure titanium and type III gold alloy plates. 27 of 33 specimens were sectioned perpendicular to their long axis with a carborundum disk and water coolant. Six specimens remained and served as the control group. A group of 6 specimens was posed as butt joints in custom parallel positioning device with a feeler gauge at each of three gaps : 0.00, 0.25. and 0.50mm. All specimens were then machined to produce a uniform cross-sectional dimension, none of the specimens was subjected to any subsequent form of heat treatment. Scanning electron microscopy was performed on representative tested specimens at fractured surfaces in both the parent metal and the weld. Vickers hardness was measured at the center of the welds with a micropenetrometer using a force of 300gm for 15 seconds. Measurement was made at approximately $200{\mu}m\;and\;500{\mu}m$ deep from each surface. One-way analysis of variance (ANOVA) and Scheffe's test was calculated to detect differences between groups. The purpose of this study is to compare the strength and properties of the joint achieved at various butt Joint gaps by the laser welding of type III gold alloy and pure titanium tensile specimens in an argon atmosphere. The results of this study were as follows : 1. When indexing and welding pure titanium, there was no decrease in ultimate tensile strength as compared with the unsectioned alloys for indexing gaps of 0.00 to 0.50mm, although with increasing gap size may come increased distortion (p>0.05). 2. When indexing and welding type III gold alloy, there were significant differences in ultimate tensile strength among groups with weld gaps of 0.00mm, 0.25 and 0.50mm, and the control group. Group with butt contact without weld gap demonstrated a significant higher ultimate tensile strength than groups with weld gaps of 0.25 and 0.50mm (p<0.05). 3. When indexing and welding the different metal combination of type III gold alloy and pure titanium, there were significant differences in ultimate tensile strength between groups with weld gaps of 0.00, 0.25, and 0.50mm. However, the mechanical properties of the welded joint would become too brittle to be acceptable clinically (p<0.05). 4. The presence of large pores in the laser welded joint appears to be the most important factor in controlling the tensile strength of the weld in both pure titanium and type III gold alloy.

• 한국레이저가공학회지
• /
• 제13권3호
• /
• pp.1-6
• /
• 2010

The in-process monitoring of $CO_2$ welding of Zn-coated steel plates has been studied and compared with that of conventional thin plates. Relationships between weld defects and plasma emission signals were evaluated in laser lap joint of thick Zn-coated steel. According to the study, weld defects were found to increase with Zn content. As a result, measured plasma emission signals also decreased. In case of plate with $15{\mu}m$-thick Zn-coated layer, defects caused by evaporation of Zn could, therfore, controled by gap of 0.1mm, resulting in a stable emission signals. However, the amplitude of signals fluctuated very widely. Variation of amplitude sould be limited in 3-8V by FFT smoothing.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.144-146
• /
• 2005

Dual electromagnetic sensor is used for sensing the weld line. The sensor consists of excitation and two sensing coil wound over the ferro-magnetic core. By using the dual sensor, the effect of noise is minimized. It is based on the generation of eddy currents in the welding plate by passing current through the excitation coil. The sensor can be used to track the butt joints having no gap between them, where a vision based sensor fails to track. Sensor sensitivity depends on the number of coil turns, frequency of excitation, distance of a sensor from the work piece, diameter of core, etc. The whole system consists of a sensor, a signal processing board, a motion controller and a personnel computer (PC). The raw sensor signal is processed using the signal processing board. It consists of amplification, rectification, filtering, averaging, offset adjustment, etc. Based on sensor data, the motion controller adjusts the position of a welding torch.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.14-17
• /
• 2015

Cleaning effect is well known mechanism of oxide layer removal in DCEP polarity. It is also known that DCEN has higher heat input efficiency than DCEP in GTAW process. Based on these two renowned arc theories, conventional variable polarity arc for aluminum welding was set up to have minimum DCEP and maximum DCEN duty ratio to achieve the highest heat input efficiency and weldability increase. However, recent several variable polarity GTA research papers reported unexpected result of proportional relationship between DCEP duty ratio and heat input. The authors also observed the same result then suggested combination of tunneling effect and random walk of cathode spot to fill up the gap between experiment and conventional arc theory. In this research, suggested combinational work of tunneling effect and rapid cathode spot changing is applied to another unexpected phenomena of variable polarity aluminum arc welding. From previous research, it is reported that wider oxide removal range, narrower bead width and shallower penetration depth are observed in thin oxide layered aluminum compared to the case of thick oxide. This result was reported for the first time and it was hard to explain the reason at that time therefore the inference by the authors was hardly acceptable. However, the suggested combinational theory successfully explains the result of the previous report in logical way.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.28-28
• /
• 2009

최근 전세계적으로 유가 상승 및 배기가스 배출 저감과 관련된 각종 환경규제에 대응하기 위하여 선진 자동차회사들은 $CO_2$ 배출 저감 기술과 기존 내연기관 차량의 연비향상을 위해 엔진성능 개선, 구동시스템의 최적화, 차량 경량화, 공기저항 감소 등에 초점을 맞춰 차량의 연비향상과 배기가스 규제에 대응하고 있다. 특히, 자동차 중량의 30%를 차지하는 차체의 경량화는 엔진효율을 높여 자동차의 성능향상을 극대화시키고, 그로 인해 연비향상을 도모할 수 있으므로 환경오염 방지와 연료절감에 가장 적합하고 효과적인 방법이다. 이에 기존의 강재에 비해 비중이 낮으면서 유사한 강도와 내식성이 뛰어난 알루미늄 합금의 차체 적용에 대한 연구가 진행되고 있다. 본 연구에서는 자동차 Door에 알루미늄 합금(Al 5052)의 적용 가능성을 판단하기 위해 반응표면분석법(Response surface methodology)을 이용하여 저입열 Pulse MIG 용접 공정변수를 최적화하였다. 첫째, 저입열 Pulse MIG 용접에서 용접 공정 변수(용접전압, 용접속도, Gap)의 변화가 비드 형상에 미치는 영향에 대해 평가하였다. 요인분석법을 이용하여 용접 공정 변수와 비드 형상 변수와의 주효과와 교호작용효과를 분석하였고, 이를 통해 비드 형상 변수에 영향을 크게 미치는 용접 공정변수를 선별하여 다중회귀분석을 통해 용접 공정 변수 변화에 따른 비드형상 예측 회귀모델을 제안하였다. 둘째, 자동차 Door 생산 현장에서 박판 알루미늄 합금 겹치기 용접 이음부의 0~1 mm 갭 발생에 대해 강건한 용접조건을 제시하기 위해 반응표면법(Response surface methodology)을 이용하여 저입열 Pulse MIG 용접 공정 변수를 최적화하였고, 그 적용 가능성을 확인하였다.

• 한국정밀공학회지
• /
• 제32권12호
• /
• pp.1017-1021
• /
• 2015

Induction heating has been applied to the preheating process in various industrial fields. It has been used as a simple device structure, limiting the heating zone through controlled variables, and free-welding positions. It would be helpful to weld thick plates with arc welding such as GMAW. The induction heating process is well suited to this process. In this study, in order to find suitable induction heating parameters, a simulation was conducted with multi physics S/W. Three kinds of material were heated by induction coils designed specially for thick plate. Consequently, steel and nimonic alloy were the most efficient materials for preheating by induction. It can be concluded that the induction heating process is a good method for preheating the thick plate.

• Journal of Welding and Joining
• /
• 제21권4호
• /
• pp.25-30
• /
• 2003

There have been many researches for small scale packages such as CSP, BGA, and Flipchip. Underfill encapsulant technology is one of the latest assembly technologies. The underfill encapsulant could enhance the reliability of the packages by flowing into the gap between die and substrate. In this paper, the effects of underfill packages by both aspects of thermal and mechanical reliabilities are studied. Especially, it is focused to value board-level reliability whether by the underfill is applied or not. First of all, The predicted thermal fatigue lifes of underfilled and no underfilled $\mu$ BGA solder joints are performed by Coffin-Manson's equation and FEA program, ANSYS(version 5.62). Also, the thermal fatigue lifes of $\mu$ BGA solder joints are experimented by thermal cycle test during the temperature, 218K to 423k. Consequently, both experimental and numerical study show that $\mu$ BGA with underfill has over ten times better fatigue lift than $\mu$ BGA without underfill.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.492-498
• /
• 2001

In the previous study, temperature monitoring of case about shrinkage fit process was performed and heat transfer model was developed in detail by feedback and tuning among monitoring result, process investigation, and analysis result. The gap element in contact between case and core was effectively used in analysis model. In present study, following things are performed to solve deformation of case due to shrinkage fit process on the basis of previous result. Above all, mechanical material properties of case are measured by case specimen for deformation analysis considering weldment of case. Deformation of case before and after shrinkage fit process is measured, too. Three dimensional deformation model is developed by the comparison and inspection between these experimental data and analysis results. Deformation analysis is simulated with the result of heat transfer analysis, in other words, non-coupled analysis is used. Finally the countermeasure for deformation is brought up through those.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.38-47
• /
• 2000

Characteristics of the interface between tube and tube sheet which were formed by explosive expansion and roll expansion, have been studied in the research. The results are as follows: Optimum amounts of explosives for the expansion of Alloy 600 (19.05mm and 15.88mm) were found to be RDX 3.5-8.5g/m. Because explosive expansion caused les strain hardening and increased bounding strength, characteristics of the explosively expanded were better than those of mechanically expanded. As the transition region of the explosive expansion is inactive, the resistance to the stress corrosion cracking increases by 30∼40% compared to the roll and hydraulic expansion.