• Proceedings of the KWS Conference
• /
• 1999.10a
• /
• pp.132-135
• /
• 1999

• Proceedings of the KWS Conference
• /
• 1998.05a
• /
• pp.239-241
• /
• 1998

• Journal of Welding and Joining
• /
• v.11 no.2
• /
• pp.13-20
• /
• 1993

The object of the research is to develop the flux for aluminum brazing. Five kinds of flux were applied to brazing joint with fin and tube structure using same filler metal. To estimate the performance of the developed flux, products analysis, differential thermal test, grain size test, observation of crystalline structure, tensile test, corrosion test were made. From the results of experiment, the following conculsions were obtained. 1. The optimum composition ratio (Wt) of AlF$_3$ and KF was 50-60% : 40-50% 2. The optimum melting point of the flux was 567-578$^{\circ}C$.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.6
• /
• pp.473-481
• /
• 2016

Thick plate is currently widely used in shipbuilding due to the increasing of size of ships. However, its use has increased welding groove angles and volume. The welder's technique must be good enough to improve productivity while preventing defects. Generally, the groove angle can be reduced to less than a flux-cored arc welding (FCAW) machine setting of $35{\pm}5^{\circ}$, requiring fewer welding passes while maintaining high productivity and reduced heat input. Therefore, welding technique can be prevented by improved mechanical properties and welding deformation. Welding defects such as lack of fusion (LF), lack of penetration (LP) and hot cracking should be considered when reducing the groove angle for related applications. In this study, a welding groove angle of $25{\pm}5^{\circ}$ is verified as suitable for FCAW design and fabrication. The experimental results confirm the effects on the strength characteristics of FCAW weldment when reducing groove angle to improve the productivity of shipbuilding industries.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.47-54
• /
• 1999

It is well known that solidification cracking often occurs in welds of root pass for one-side welding under the conditions of high welding currents and speeds. In this study, the solidification in 590MPa class steel for pressure vessels SPPV490 was investigated by using flux-cored arc welding(FCAW) with 4 types of welding wires and welding conditions of 200∼280A and 2.8∼ 4.2mm/sec. In order to compared the result of cracking in SPPV490, 0.2%C steel for welded structure of SWS400 and 0.45%C steel for machine structural SM45C were also used as base metals. As the results, all the cracks formed in some welding conditions were observed near the center of weld bead. The solidification cracks were generally initiated near the upper surface of bead and propagated toward the inner part. The solidification cracking generally increased with welding current and welding speed in the same base metal and welding material. In cracking susceptibility, SPPV490 showed higher cracking susceptibility than SWS400 in all welding conditions and welding materials. It was considered that cracking susceptibility could not be evaluated with the hardness of weld metals. The cracking ratio increased with decreasing of a/b(a and b; the width of the upper surface and the back surface of the bead) as shape factor of bead. The cracking tendency with shape factor of bead was extended under the condition of higher welding currents.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.17-22
• /
• 2011

As the quality of a weld joint is strongly influenced by process parameters the welding process, an intelligent algorithms that can predict the bead geometry and shape to accomplish the desired mechanical properties of the weldment should be developed. In this study, prepared by ${\Phi}1.6mm$ GMA welding of metal wire nose Advice jowelui 350A 600A grade level inverter welder and DAIHEN SCR's were carried out using welding. Welding conditions were 5.5m/min wire feed rate the welding current is rapidly transmit approximately 260A, welding voltage was about 30V. CTWD a 22mm, shielding gas was Ar 20L/min and the welding speed was a 240mm/min. Using data collected during welding equipment welding current and welding voltage waveform was analyzed by measuring the volume of the transition mode. Addition of $CaCO_3$ as a loss of the spread of the weld bead dilution rate decreased, suggesting that, GMA in the overlay welding bead shape control, dilution control and may be used as a welding flux is considered. Stabilizing effect of the arc by the Ca-containing $CaF_2$, $CaCO_3$, $CaMg(CO_3)_2$, respectively, welding flux 0.1wt.% added GMA welding and weld overlay were evaluated with dilution, $CaF_2$, and $CaMg(CO_3)_2$ added to the dilution of Seemed to increase.

• Applied Chemistry for Engineering
• /
• v.34 no.4
• /
• pp.450-454
• /
• 2023

Chloride ions in the alloy powder used as flux in Flux Cored Arc Welding (FCAW) can cause pores on the bead surface of the welding metal to cause defects, or chloride remaining in the alloy powder can cause corrosion of the metal. Combustion-ion chromatography is mainly used to quantify the chloride ions in alloy powder, but there is a limitation in that the equipment is expensive and requires a high degree of expertise. Therefore, this study aims to find an easy and accurate quantification method in the field by comparing combustion-ion chromatography (C-IC), which is mainly used for chloride ion quantification of alloy powder, X-ray fluorescence analysis (XRF), and potentiometric titration. In this article, magnesium-aluminum alloy powder is applied to the quantification of chloride ions because it is most commonly used as flux. This study confirmed that potentiometric titration can be applied to the quantification of chloride ions in the alloy powder in the industry field.

• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.57-63
• /
• 1987

A method which can be used for evaluating slag detachability is proposed in this study. The proposed method was intended to get an absolute value for slag detachability, to give consistent value for a given welded joint, and finally to be simple to test. With a test fig made in this study, an impact by dropping a steel ball (13Kg in weight) is applied on the back side of an as-welded plate having a slag layer on the weld bead. Such impact applied forces the slag to drop off from the bead surface. In order to make a quantitative evaluation the amount of slag removed was measured with increasing the number of drops. Using this method six kinds of fluxes were evaluated in terms of the effects of flux type, basicity and weding variables on the slag detachability. As an initial result of this test, it was found that welding heat input affects the detachability significantly. Most importantly the evaluation made using the presently proposed method gives the same order of ranking as that of the actual practice done by a welder.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.6
• /
• pp.860-864
• /
• 2012

The contact tip is higher the wear of resistance and the longer life are demanded to GMA welding process. In this study, four different contact tips with three different compositions by two wires were evaluated their wear resistance by measuring in every one hour the area of enlarged hole at the exit side during actual wleding. Experimental results clearly showed that the Cr-containing tips strengthened by precipitation hardening have much better resistance to wear than those made by work hardening. In addition, flux cored wire is excellent abrasion resistance test results showed. Based on these results, the domestic industry, the life of the contact tip to know will be used as basic data.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.495-496
• /
• 2013