• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.1036-1041
• /
• 1997

The objective of this study is to adjust the roll gap for the dimension accuracy of bar in hot bar rolling process considering roll wear. In this study hot bar rolling processes for round and oval passes have been investigated. In order to predict the roll wear, the wear model is reformulated as an incremental form and then wear depth of roll is calculated at each deformation step on contact area using the results of finite element analysis, such as relative sliding velocity and normal pressure at contact area. Archard's wear model was applied to predict the roll wear. To know the effects of thermal softening of DCI (Ductile Cast Iron) roll material according to operating conditions, high temperature micro hardness test is executed and a new wear model has been proposed by considering the thermal softening of DCI roll expressed in terms of the main tempering curve. The new technique developed in this study for adjusting roll gap can give more systematically and economically feasible means to improve the dimension accuracy of bar with full usefulness and generality.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1441-1455
• /
• 1993

Under unlubricated condition, the friction and wear tests of silicon nitride and zirconia manufactured by HIP were carried out at room temperature. The wear resistance of silicon nitride was superior to that of zirconia under low load, whereas the wear resistance of zirconia was superior to that of silicon nitride under high load. Wear model of ceramic was suggested by the microscopic SEM observation of worn surfaces and debris. Theoretical analysis and discussions based on linear fracture mechanics were made out about this ceramic wear model. From the theoretical analysis, a new nondimensional parameter, Scf, was introduced to estimate wear rate of ceramics. This new nondimentional parameter consists of contact pressure, surface defect of contact material, frictional coefficient and fracture toughness.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.109-124
• /
• 2015

This paper presents a wear analysis procedure for the journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. A journal bearing is in the mixed elastohydrodynamic (EHL) lubrication region when the shaft speed is less than the corresponding lift-off speed. Below the lift-off speed, a wear scar can form on bearing surfaces. In part 1 of this paper, we develop the appropriate formulations and the calculation procedure for the analysis. Specifically, we formulate an equation for modified film thickness in a journal bearing considering the additional wear volume. In order to obtain the modified specific wear rate induced by the modified Archard’s wear coefficient, we utilized the extended non-dimensional diagram for the specific wear rate, k, the fractional film defect coefficient, Ψ and the asperity load sharing factor, γ₂. This asperity load sharing factor is newly calculated by setting the Zhao-Maietta-Chang (ZMC) asperity contact pressure equation coupled with the central film thickness equation derived by using the ZMC asperity contact model equal to the modified central contact pressure derived by using the central (or maximum) contact pressure at the dry rough line-contact configuration. We can use the procedure introduced in this paper to determine the lifetime (or longterm) linear wear in radial journal bearings that is a result of repeated stop-start cycles.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.49-56
• /
• 1987

This paper is a study on the effect of the cutting speed on the tool wear in turning of the glass fiber reinforced plastics. The wear behavior of cutting tool is studied by means of turning, changing the cutting speed and feed in the wide range. Moreover, the theoretical model applicable to the cutting speed of wide range is analysed. The main results obtained are as follows: The relation between the tool wear and the cutting speed is divided into three range in case of the constant cutting distance. 1) At the low cutting speed, the tool wear is independent of the cutting speed, but dependent mainly on the contact length between tool and glass fiber(lst range). 2) At the high cutting speed, the tool wear is independent of the contact length, and dependent on the cutting speed only(2nd range). The tool wear increases in proportion to the cutting speed. 3) At the higher cutting speed than the speed in the 2nd range, the tool wear is independent both of the cutting speed and the contact length(3rd range). 4) In the 3rd range, tool flank wear is constant and is observed that only the wear of cutting edge increases.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.9
• /
• pp.983-989
• /
• 2011

A numerical algorithm for predicting fretting wear was developed using the boundary element method (BEM). A contact analysis was performed numerically using the relation between the elastic displacement and uniformly distributed loading of a rectangular patch on a semi-infinite solid. Geometrical updating based on nodal wear depths was performed. The wear depths were computed using the Archard's equation for sliding wear. In order to investigate the efficiency of BEM for predicting fretting wear, a problem involving a two-dimensional cylinder on a flat contact was analyzed, comparing it with the simulation model proposed by McColl et al. that was based on the finite element method. The developed method was then applied to the analysis of a spherical contact and it was shown that the developed simulation technique could efficiently predict fretting wear. Moreover, the effect of a step cycle on the solution obtained by the developed method was investigated.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.135-142
• /
• 2000

This Paper describes a characteristics of wheel wear of high speed train running on the conventional line. Conventional line has many curved tracks that cause severe wheel flange wear. The influences of lubrication, cant deficiency, owe radius on wheel wear are also described considering the operation performance of the highspeed trainset. A method of calculation using contact patch work model is presented far determination of the evolution by wear of railway wheels.

• Tribology and Lubricants
• /
• v.36 no.6
• /
• pp.320-323
• /
• 2020

Thin film coatings are commonly exploited to minimize wear and optimize the frictional behavior of various precision mechanical systems. The enhancement of thin film durability is directly related to the performance maximization of the system. Therefore, a fine approach to analyze the thin film wear behavior is required. Archard's equation is a representative and well-developed law that defines the wear coefficient, which is the probability of creating wear particles. A ploughing model is a commonly used model to determine the friction force during the abrasive contact. The equations demonstrate that the friction force and wear coefficient are inversely proportional to the hardness of the material. In this study, Archard's equation and ploughing models are modified with an effective hardness to minimize the gap between the experimental and numerical results. It is noted that the effective hardness is the hardness variation with respect to the penetration depth owing to the substrate effect. The nanoindentation method is utilized to characterize the effective hardness of Cu film. The wear coefficient value considering the effective hardness is more than three times higher than that without considering the effective hardness. The friction force predicted with the effective hardness agreed better with the results obtained directly from the friction force detecting sensor. This outcome is expected to improve the accuracy of friction and wear amount predictions.

• Tribology and Lubricants
• /
• v.18 no.2
• /
• pp.160-166
• /
• 2002

In case of rough contact fatigue, the accurate calculation of surface tractions is essential to the prediction of crack initiation life. Accurate Surface tractions influencing shear stress amplitude can be obtained by contact analysis based on the morphology of contact surfaces. In this study, to simulate rough contact under sliding condition, gaussian rough surface generated numerically in the previous study was used and to calculate clack initiation life in the substrate, dislocation pileup theory was used.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.72-79
• /
• 2000

In case of rough contact fatigue, the accurate calculation of surface tractions is essential to the prediction of crack initiation life. Accurate Surface tractions influencing shear stress amplitude can be obtained by contact analysis based on tile morphology of contact surfaces. In this study, to simulate rough contact under sliding condition, gaussian rough surface generated numerically in the previous study was used and to calculate crack initiation life in the substrate, dislocation pileup theory was used.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.178-188
• /
• 2003

The wear of steam generator tubes is due to the vibration occurred between tubes and tube supporters. To predict the future wear depth, the wear constants of the impact and the sliding model is used. The wear constants, 3C/2 and K/3H, are found inversely from known wear depth and time. Using these constants, the future wear depths are found from two bodies that deform the elliptical shape. The results are compared with the measured wear depth of steam generator tubes in a nuclear power plant. The results show that the predicted wear depth envelopes the measured wear depth.