• Tribology and Lubricants
• /
• v.19 no.3
• /
• pp.151-158
• /
• 2003

In metal cutting at the tool-chip interface, friction generates considerable amount of heat. Thus, the knowledge of wear properties of cutting tool material in high temperature has been as one of important factors in need of clarification. The authors presented the wear properties of 5%Co-5%V-1%Nb high speed steel, fabricated by powder metallurgy, in room temperature in previous articles. The objective of this paper is to clarify the effects of temperature on its wear properties. Wear tests in sliding conditions under various temperatures have been conducted using the pin-on-disc type wear test machine. The results indicate that the wear properties of 5%Co-5%V-1%Nb high speed steel in high temperature as well as in room temperature are excellent. It may be deduced that the oxide layer formed on worn surface at high temperature is stable enough to prevent wear due to the high temperature strength of its matrix.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3083-3093
• /
• 1993

Friction and wear at ceramic coated surfaces of aluminum alloy were experimentally studied using a Ring-on-Block wear test machine. Ceramic materials coated on aluminum alloy surfaces were WC, CrC, $Al_{2}O_{3}$ by a plasma spray; and $Al_{2}O_{3}$,$Al_{2}SiO_{5}$, $Na_{2}B_{4}O_{7}$,$Na_{4}P_{2}O_{7}$, and $Al_{2}O_{3}-ZrO_{2}$ composite coating by an Anodic Spark Depositon. They were tested under the sliding wet contact and compared with aluminum alloys and steels. Test results showed that ceramic coated surfaces, in general, have better anti-wear property than those of aluminum alloys due to increase in the surface hardness ; however, they also showed higher coefficients of friction and changes in wear mechanisms, resulting in brittle fractures.

• Transactions of Materials Processing
• /
• v.26 no.6
• /
• pp.365-371
• /
• 2017

During sling wear of a ferrous metal, a surface layer is formed. Its microstructure, constituting phases, and mechanical property are different from those of the original wearing material. Since wear occurs at the layer, it is important to characterize the layer and understand how wear rate changes with different layers. Various layers are formed depending on external wear conditions such as load, sliding speed, counterpart material, and environmental conditions. In this research, sliding wear tests of pure iron were carried out against two different counterparts (AISI 52100 bearing steel and $Al_2O_3$) in the air and in an inert Ar gas atmosphere. Pure iron was employed to exclude other effects from secondary phases in steel on the wear. Wear tests were performed at room temperature. Worn surfaces, wear debris, and cross-sections were analyzed after the test. It was found that these two different counterparts and environments produced diverse layers, resulting in significant changes in wear rate. Against the bearing steel, pure iron showed higher wear rate in an Ar atmosphere due to severe adhesion than that in the air. On the contrary, the iron showed much higher wear rate in the air against $Al_2O_3$. Different layers and wear rates were analyzed and discussed by oxidation, severe plastic deformation, and adhesion at wearing surfaces.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.76-80
• /
• 2010

Oil hydraulic piston pumps are being extensively used around the world, because of their simple design, light weight, effective cost, etc. An oil hydraulic pump is likely to have the serious problems of high leakage, friction, and low energy efficiency after a long period of use. In an oil hydraulic piston pump, the clearance between the valve block and piston plays an important role for volumetric and overall efficiency. In this study, the wear property of the SACM645 material with DLC coating used for a hydraulic piston pump was determined by experimentation with variable heat treatment. To investigate the effect according to the piston surface condition, five different types of specimens were prepared. The maximum tensile strengths of the QT and QT Nitration specimens had similar values of about 800 MPa, but the strains indicated a big difference. In a wear test, the wear characteristic of the DLC coating specimen was shown to be excellent. The QT, QT + IH, QT + Nitration, and matirx specimen showed similar wear characteristics. In the case of a dry condition without oil, the DLC coating specimen had good wear resistance, with no wear shown.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.379-380
• /
• 2002

Steam generators (S/G) of pressurized water reactors are large heat exchangers that use the heat from the primary reactor coolant to make steam in the secondary side for driving turbine generators. Reciprocating sliding wear experiments have been performed to examine the wear properties of Incoloy 800 and Inconel 690 steam generator tubes in high temperature water. In present study, the test rig was designed to examine the reciprocating and rolling wear properties in high temperature (room temperature - $300^{\circ}C$) water. The test was performed at constant applied load and sliding distance to investigate the effect of test temperature on wear properties of steam generator tube materials. To investigate the wear mechanism of material, the worn surfaces were observed using scanning electron microscopy. At $290^{\circ}C$, wear rate of Inconel 690 was higher than that of Incoloy 800. It was assumed to be resulted from the oxide layer property difference due to the a\loy composition difference. Between 25 and $150^{\circ}C$ the wear loss increased with increasing temperature. Beyond $150^{\circ}C$, the wear loss decreased with increasing temperature. The wear loss change with temperature were due to the formation of wear protective oxide layer. From the worn surface observation, texture patterns and wear particle layers were found. As test temperature increased, the proportion of particle layer increased.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.50-57
• /
• 1995

When engine oil is used under severe running condition, the Lubricational characteristics is very important. I have studied the Lubricational characteristics with Compound Additives of engine oil for the Falex wear test machine. Adding detergent (Ca-phenate) to engine oil, the seizure is more improved than in case of non-adding, and adding Zn-DTP (Zinc dialkyl dithio phosphate), the extreme pressure property is excellent at the high load. But when the PTFE (Polytetra Fluoro Ethylene) and MoS$_{2}$ (Molybdenum disulfide) are added, the temperature characteristics and the anti-wear property become excellent because the stability can be maintained in a high temperature. The result are as follows, it can be improved that when the compound of the Ca-phenate and Zn-DTP, MoS$_{2}$, PTFE, etc. was added to engine oil, the lubrication characteristics become better. It is argued that it is improved because of excellence of the anti-wear, the extreame pressure properties and the heat stability.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.2
• /
• pp.1-7
• /
• 2005

In order to determine the wear Properties of PECVD ceramic coatings, wear process was evaluated using the coated pin of Falex Tribosystem. Coating materials deposited wear the TiC, TiN and Ti(CN). An experimental process was established to determine the tribological characteristics of friction and wear behavior under the variation of applied load, temperature and sliding distance by the Falex test machine. The experimental results indicate that TiN coating compared with TiC coating on e materials have e excellent friction and wear characteristics. However TiC coating compared i친 TiN coatings have a low friction coefficient with steel and good thermal stability, and Ti(CN) has the excellent anti-wear properly as well as the superiority of extreme pressure property. Compound coating compared wi simple coatings show improved tribological characteristics.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2122-2132
• /
• 1995

There are some cases which require to grasp the abrasion resistance property in the fields of the high-technology to be required the high specific strength and modulus. In this study, wear test with the various test temperature and velocity were performed in the SiCw/A16061 composite and A16061 matrix using the wear test machine of the ring-on-disc type. As the results, the friction and wear properties by various test temperature and velocity were examined. The worn surface has observed by scanning electron microscope in order to examine the wear mechanism.

• Tribology and Lubricants
• /
• v.25 no.2
• /
• pp.114-119
• /
• 2009

Fretting occurs wherever short amplitude reciprocating sliding between contacting surfaces is sustained for a large number of cycles. The fundamental characteristic of fretting is the very small amplitude of sliding and combination of different wear mechanism. Predicting wear is important to enhance reliability of the parts. The objective of this paper is to predict fretting wear by using a contact analysis considering wear process. This construction will give us important information to know a property of fretting wear.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.267-273
• /
• 2009

Three types of structural intermetallic compounds, $Ni_3Al$, NiAl and TiAl, having each single phase structure without pores were produced by arc-melting process. Their sliding wear properties were investigated against a hardened tool steel. It was shown that the wear of the intermetallic compounds was hardly occurred against the hardened tool steel. TiAl compound showed the best wear resistance among them. In this case, wear was preferentially occurred on the surface of the hardened tool steel of the mating material which has higher hardness. It could be found that the wear mode on intermetallics without pores by arc-melting process was different from that on its porous layer coated on steel by combustion synthesis.