• 한국재료학회지
• /
• 제12권8호
• /
• pp.669-675
• /
• 2002

CrN film coated by AIP method, improved the mechanical properties (Hardness, Roughness, wear and fatigue) of Ti-6Al-4V alloy. The properties were studied using GXRD, XPS, Hardness, Roughness, wear and fatigue testers. CrN thin film thickness was about 7.5$\mu\textrm{m}$ and grew with (111) orientation. Hardness of CrN thin film was very high (Hv 1390) and roughness of the surface layer was greatly improved (Ra=0.063$\mu\textrm{m}$) compared with matrix alloy (Ra=0.321$\mu\textrm{m}$). Such changes of hardness and roughness could be contributed to improving the wear resistance and fatigue life. Striation like pattern with dimples and voids, a typical fatigue fracture mode, was observed throughout the specimen.

• Tribology and Lubricants
• /
• 제11권1호
• /
• pp.37-43
• /
• 1995

Sputtering parameters such as N$_{2}$ flow percentage and bias voltage in reactive TiN film deposition by RF magnetron sputtering system were selected to investigate the effects of sputtering deposition conditions on tribological characteristics of TiN films. Wear scar of the steel ball damaged by TiN films was measured by SEM to understand wear behavior of deposited TiN films. Crystallization and induced strain of TiN were detected by XRD. Wear mode changed from plastic to brittle with increasing N$_{2}$ ratio. Wear scar by sliding with TiN film deposited at around 27% N$_{2}$ ratio was maximum. The results indicate that bias voltage affects tribological behavior by formation of high density film and internal stress.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.144-149
• /
• 1995

Use of high-quality basestocks is increasing to produce high-performance lubricants. However, their tribological characteristics have not been understood clearly yet. In this study, a newly developed basestock from a fuel hydrocracker and a poly-alpha-olefin are selected and investigated on the properties of lubricants formulated with them. The Lubricants are prepared by blending the basestocks with typical additives such as a zinc dialkyldithiophosphate, a dispersant, a detergent and a dispersant-inhibitor package. Frictional and wear-preventing properties are investigated using an oscillating-type wear-testing machine. The contact is a ball-on-disk mode and the testing temperature is varied from room temperature to 200$^{\circ}$C. The results show that their frictional property is varied significantly and that the non-conventional oils result in lower friction and lower wear compared with conventional lubricants, especially at the higher temperatures.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.964-965
• /
• 2006

The injection molded Fe sintered bodies were fabricated using two kinds of nano Fe powders, $Fe-5%vol.ZrO_2$ and $Fe-10vol.%ZrO_2$ powders. The relationship between microstructure and mechanical properties depending on the $ZrO_2$ contents and sintering temperature were characterized by SEM and TEM techniques. In the wear test, the $Fe-0vol%ZrO_2$ sintered bodies showed mainly adhesive wear, but in the Fe-5%vol. $ZrO_2$ and Fe-10vol. % $ZrO_2$ composites the main wear behavior showed abrasive wear mode.

• 한국표면공학회지
• /
• 제30권6호
• /
• pp.400-405
• /
• 1997

The experimental study has been performed to deposit to deposit chromia powder on magnssium alloy for tribological and mechanical properties. The optimal condition was obtained by changing the spray condition such as working distance and gun power. As ceramics was coated onto the a light metal such as Mg according to the weight reduection of the car engine block, it could acquire that the engine efficiency deu to the weight reduction and properties such as resistance to heat, as well as wear. Coating qualities are discussed with respect to hardness, tribologicalproperty, and microstructure. The tribological and mechanical properties are investigated by using the reciprocal configuration tribometer and microharduess tester. Wear mode is determined by observing the SEM morhpology of wear track and cross section view of wear track.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.528-530
• /
• 2008

The effect of consolidation temperature on the microstructure, density and mechanical properties (especially, wear property) of $Al_{92.5}-Fe_{2.5}-Cr_{2.5}-Ti_{2.5}$ alloy fabricated by gas atomization and magnetic pulsed compaction was investigated. All consolidated alloys consisted of homogeneously distributed fine-grained fcc-Al matrix and intermetallic compounds. Relative higher mechanical properties in the MPCed specimen were attributed to the retention of the nanostructure in consolidated bulk without cracks. The as consolidated bulk by magnetic pulsed compaction showed the enhanced wear properties than that of a general consolidation process. In addition, the wear mechanism and fracture mode of MPCed bulk was discussed.

• 한국철도학회논문집
• /
• 제10권5호
• /
• pp.607-612
• /
• 2007

본 논문에서는 도시철도 차량의 운전모드에 의한 레일마모 현상을 역행, 타행, 제동 세구간 별로 나누어 레일 마모 현상을 비교 분석하였고, 또한 ATO 로깅데이터에서 실제 운행한 속도데이터를 가속도와 감속도 데이터로 변환하여 열차의 가속도의 견인력과 감속도의 제동력에 의해 발생되는 레일마모량을 비교 분석한 결과로 통해 궤도 관리에 적용할 수 있는 방안을 제시하고자 한다.

• 한국의류학회지
• /
• 제22권2호
• /
• pp.193-202
• /
• 1998

The purpose of this study was to understand clothing condition of elderly men focusing on somatotype variation and satisfaction with ready-to-wear and to provide basic data in designing ready-to-wrar for the elderly men. The questionnaire method was used and one-to-one interviews were held for the elderly residents in Seoul, Deajon, Jonju, and Yeosu areas. The total of 275 questionnaires (from 148 elderly men in the 60's, 99 in the 70's and 28 in the 80's) were collected and used for statistics. SAS package was used for the statistics and the statistics were based on frequency, X2-test, ANOVA, Duncan's multifle range test. The results of the study were as follows; 1) Height (p< .05), weight (p< .001) and Rohrer index (p< .05) decreased significantly with ageing 2) The somatotypes of 75.6% were changed and the 70's 8t the 80's showed significantly (p< .05) higher changing rate compared to the 60's and more changes took place significantly (p< .001) with ageing. 3) The most preferred out wear was suit & tie and next was jumper or shirt. 4) For the mode of getting suit, the highest number 55.3%) purchased ready-to-wear, next (32.0%) was tailored and the least (12.7%) neither purchased nor tailored. The percentage of buying ready-to-wear significantly (p< .01) decreased with ageing. The main reason for getting tailor-made was not well fitting of ready-to-wear (20.7% out of 32.0%). And for the mode of getting suit, there was significant differance with income (p< .001) and pocket money (p< .01). 5) The most important factors in suit and shirt werefirst, size (fitness) and second, comfort in movement. 6) For the wearing feeling of suit, 55.3% showed discomfort. There was significant difference according to the age (p< .05) and pocket money (p< .05). The Discomfort increased with ageing and less pocket money. 7) 62.4% answered it uneasy to Pick out well fitting If comfortable suit. This showed their dissatisfaction with ready-to-wear. 8) As for the items of not well fitting, 64.4% answered in jacket, 60.8% in trousers, 46.0% in shirt. The above result shows that elderly men's somatotype changes as they age, suit is found uncomfortable and it's not easy for elders to pick out comfortable ready-to-wear. So, they seem to have a certain dissatisfaction in ready to wear. Therefore, there is a need for reorganization of size and developing pattern design according to measurement of elderly men.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.442-449
• /
• 2000

Before the complete construction of new high-speed line between Seoul and Pusan, KTX is going to operate on both new high-speed line between Seoul and Daegu and electrified conventional lines between Daegu and Pusan. Then, the wheels of KTX are going to operate on various rails such as KS50N and KS60 of conventional line as well as UIC60 of high-speed line. Also, conventional line will have a mixed traffic mode with various types of trains operating on it, such as Saemaul and Mugunghwa. Hence, this study reviews the wear phenomena of wheels and rails in geometrical point of view by comparing their profiles. The analyses of the results show that because UIC60 rail is designed for KTX, KS50N rail whose profile is similar to that of UIC60 will not have any impact on the shape of wheel wear. On the other hand, KS60 rail is expected to have partial wear on both the flange of KTX wheel and the gauge corner of the rail in the initial stages. However, the operation of the trains whose wheels have 1/20 conicity will cause partial sidewear on the inside of the rail and the movement of the contact point between KTX wheel and the rail toward the inside of the track. As a result, the flange wear of KTX wheel will be reduced and the formation of wear-equilibrium profile will be faster.

• 품질경영학회지
• /
• 제36권1호
• /
• pp.31-39
• /
• 2008

This paper proposes a method of estimating the lifetime distribution at use condition for constant stress accelerated life tests when an infant-mortality failure mode as well as wear-out one exists. General limited failure population model is introduced to describe these failure modes. It is assumed that the log lifetime of each failure mode follows a location-scale distribution and a linear relation exists between the location parameter and the stress. An estimation procedure using the expectation and maximization algorithm is proposed. Specific formulas for Weibull distribution are obtained. An illustrative example and the simulation results are given.