• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.221-225
• /
• 2008

This paper presents a self-tuning controller for pressurized water reactor (P.W.R.). This self-tuning controller includes two substantial steps, such as parameter identification and control-law building in each cycle. Extended least square algorithm is used for parameter identification, Kalman filter is used for state estimation, and discrete Riccati equation is used for optimal control. Effectiveness of this algorithm is shown through computer simulation and sensitivity analysis.

• Geomechanics and Engineering
• /
• v.24 no.5
• /
• pp.419-430
• /
• 2021

Investigation on the compressibility and shear strength of compacted loess is of great importance for the design and operation of engineering infrastructures in filling area. In this study, the mechanical behaviors of Yan'an compacted loess are investigated at various dry densities and water contents by conducting one dimensional compression and direct shear tests. And the elastic compressibility, plastic compressibility, yield stress and strength are obtained from the experiments. Results show that when water content increases, plastic compressibility parameter increases, but yield stress decreases. However, the increase of dry density leads to a decrease in plastic compressibility parameter but an increase in yield stress. In addition, elastic compressibility parameter is found to be a constant which is irrelevant to water content and dry density. As for strength, cohesion and internal friction angle is directly proportional to dry density, but inversely proportional to water content. Moreover, the mercury intrusion porosimetry (MIP) and scanning electron microscope (SEM) tests were also performed to observe the pore size distribution and microstructure of the specimens. Finally, by using results of MIP and SEM tests, the compressibility and strength behaviours of Yan'an compacted loess are explained from the perspective of pore-size distribution and microstructure.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1919-1924
• /
• 2006

In this study, the run-up of water waves on slopes of s-berm breakwaters was investigated by performing a series of hydraulic experiments. The run-up height was analyzed in detail by using the effects of wave steepness and surf similarity parameter. In general, the run-up heights were decreased as the height and the width of berm were increased. However, the variation of run-up height was small for change of wave steepness and surf similarity parameter.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.344-352
• /
• 1993

The purpose of this study is to investigate the possibility of the non-destructive quality evaluation for food by the acoustic non-linear parameter B/A which is a measure of the non-linearity of the state equation of the medium in terms of pressure and density. The B/A of water, corn oil O/W(oil in water) emulsion and milk were measured by using a sound velocity measuring system. The B/A value of water was measured for ascertaining reliability of our experimental system. Corn oil W/W emulsion was prepared as a model of milk . It was proved that the B/A value of O/W emulsion was related to the oil concentration by a law of mixture. We applied this result to milk and obtained satisfactory results for predicting the milk fat concentration.

• Journal of Radiation Protection and Research
• /
• v.15 no.2
• /
• pp.101-112
• /
• 1990

For the performance assessment of the radioactive waste disposal system (repository), a biosphere model is suggested. This biosphere model is intended to calculate the annual doses to man caused by the contaminated river water for eight pathways and four radionuclides. This model can also be applied to assess the radiological effects of contaminated well water. To account for the uncertainties on the model parameter values, parameter distributions are assigned to these model parameters. Then, Monte Carlo simulation method with Latin Hypercube sampling technique is used. Also, sensitivity analysis is performed by using the Spearman rank correlation coefficients. It is found that these methods are a very useful tool to treat uncertainties and sensitivities on the model parameter values and to analyze the biosphere model. A conversion factor is proposed to calculate the annual dose rate to humans arising from a unit radionuclide concentration in river water. This conversion factor allows for the substitution of the biosphere model in a probabilistic performance assessment computer code by one single variable.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.51 no.4
• /
• pp.49-55
• /
• 2009

This paper is to induce design floods through L-moment with 3 and 4 parameter Kappa distributions including test of independence by Wald-Wolfowitz, homogeneity by Mann-Whitney and outlier by Grubbs-Beck on annual maximum flood flows at 9 water level gaging stations in Han, Nakdong and Geum Rivers of South Korea. After analyzing appropriateness of the data of annual maximum flood flows by Kolmogorov-Smirnov test, 3 and 4 Kappa distributions were applied and the appropriateness was judged. The parameters of 3 and 4 Kappa distributions were estimated by L-moment method and the design floods by water level gaging station was calculated. Through the comparative analysis using the relative root mean square errors (RRMSE) and relative absolute errors (RAE) calculated by 3 and 4 parameter Kappa distributions with 4 plotting position formulas, the result showed that the design floods by 4 parameter Kappa distribution with Weibull and Cunnane plotting position formulas are closer to the observed data than those obtained by 3 parameter Kappa distribution with 4 plotting position formulas and 4 parameter Kappa distribution with Hazen and Gringorten plotting position formulas.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.448-448
• /
• 2018

In this study, the regression models (Load ESTimator and eight-parameter model) were evaluated to estimate instantaneous pollutant loads under various criteria and optimization methods. As shown in the results, LOADEST commonly used in interpolating pollutant loads could not necessarily provide the best results with the automatic selected regression model. It is inferred that the various regression models in LOADEST need to be considered to find the best solution based on the characteristics of watersheds applied. The recently developed eight-parameter model integrated with Genetic Algorithm (GA) and Gradient Descent Method (GDM) were also compared with LOADEST indicating that the eight-parameter model performed better than LOADEST, but it showed different behaviors in calibration and validation. The eight-parameter model with GDM could reproduce the nitrogen loads properly outside of calibration period (validation). Furthermore, the accuracy and precision of model estimations were evaluated using various criteria (e.g., $R^2$ and gradient and constant of linear regression line). The results showed higher precisions with the $R^2$ values closed to 1.0 in LOADEST and better accuracy with the constants (in linear regression line) closed to 0.0 in the eight-parameter model with GDM. In hence, based on these finding we recommend that users need to evaluate the regression models under various criteria and calibration methods to provide the more accurate and precise results for pollutant load estimations.

• Journal of Korean Society on Water Environment
• /
• v.40 no.4
• /
• pp.179-194
• /
• 2024

Biophysicochemical processes in water environments and treatment systems have been great concerns of engineers and scientists for controlling the fate and transport of contaminants. These processes are practically formulated as mathematical models written in coupled differential equations. However, because these process-based mathematical models consist of a large number of model parameters, they are complicated in analytical or numerical computation. Users need to perform substantial trials and errors to achieve the best-fit simulation to measurements, relying on arbitrary selection of fitting parameters. Therefore, this study adopted a Bayesian calibration method to estimate best-fit model parameters in a systematic way and evaluated the applicability of the calibration method to biophysicochemical processes of water environments and treatment systems. The Bayesian calibration method was applied to the microbial growth-decay kinetics and flocculation kinetics, of which experimental data were obtained with batch kinetic experiments. The Bayesian calibration method was proven to be a reasonable, effective way for best-fit parameter estimation, demonstrating not only high-quality fitness, but also sensitivity of each parameter and correlation between different parameters. This state-of-the-art method will eventually help scientists and engineers to use complex process-based mathematical models consisting of various biophysicochemical processes.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1343-1349
• /
• 2010

This paper presents the behavior of the soil based on the Gap Parameter during the Shield TBM tunnel excavation in sandy soil. This study reproduced the tunnel before and after the excavation according to the diameter of the tunnel, water ratio and depth to execute a Scaled Model Test and analyzed the behavior change of the upper soil. As a result, tunneling after for soil stress decreased was similar in all the Case. In addition, the soil stress decreased was in water ratio increases.

• Journal of Korea Water Resources Association
• /
• v.33 no.S1
• /
• pp.3-10
• /
• 2000

A newly developed heuristic algorithm, Harmony Search, is applied to the parameter calibration problem of the nonlinear Muskingum model. The Harmony Search could, mimicking the improvisation of music player, find better parameter values for in the nonlinear Muskingum model than five other methods including another heuristic method, genetic algorithm, in the aspect of SSQ(the sum of the square of the deviations between the observed and routed outflows) as well as in the aspects of SAD(the sum of the absolute value of the deviations), DPO(deviations of peak of routed and actual flows) and DPOT(deviatios of peak time of routed and actual outflow). Harmony Search also has the advantage that it does not require the process of asuming the initial values of desing parameters. The sensitivity analysis of Harmony Memory Considering Rate showed that relatively large values of Harmony Memory Considering Rate makes the Harmony Search converge to a better solution.