• Journal of Biosystems Engineering
• /
• v.8 no.1
• /
• pp.38-46
• /
• 1983

This study was carried out to investigate the possibility of improving the performance of a kerosene engine with water addition. The engine used in this study was a single-cylinder, four-cycle kerosene engine with the compression ratio of 4.5. Water could be successfully added into the inlet manifold by an extra carburetor for the volumetric ratios of 5, 10, 20, and 30 percents. Variable speed tests at wide-open throttle were performed for five speed levels in the range of 1,000 to 2,200rpm for each fuel type. Volumetric efficiency and brake specific fuel consumption were determined, and brake thermal efficiency based on the lower heats of combustion of kerosene was calculated. To examine variation in fuel consumption, CO concentration, and cooling water temperature, part load tests were also performed. The results obtained are summarized as follow. (1) Brake torque increased almost in proportion to volumetric efficiency. But the ratio of increase in torque was greater than that of volumetric efficiency. Mean torque over the speed range of 1,000 to 2,200rpm increased 1, 3, 7, and 2 percents for 5, 10, 20, and 30 percents water addition, respectively. The increase in brake torque with water addition was greater at lower speeds. (2) Mean brake specific fuel consumption over the speed range of 1,000 to 2,200rpm decreased 1, 2, 3, and 3 percents for 5, 10, 20, and 30 percents water addition, respectively. (3) Mean temperature of cooling water over the speed range of 1,000 to 2,200rpm decreased 2, 4, 8, and 12 percents for 5, 10, 20, and 30 percents water addition, respectively. (4) The effects of decreasing CO concentration in the exhaust emissions with water addition were significant. At the speed range of 1,000 to 2,200rpm, CO concentration in the exhaust emissions decreased 2, 10, 23, percents for 5, 10, and 20 percents water addition, respectively. (5) Deposits were not discovered in the combustion chamber during the experiment. However, a little rust was formed in the water-supply carburetor.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.641-646
• /
• 2016

The effects of water addition on $Y_2O_3$ coatings or thick films prepared by plasma suspension spray (SPS) have been investigated. Water addition in suspension media was found to be effective to control the color of a $Y_2O_3$ coating prepared by SPS. The color changed with water addition at the shortest stand-off distance of 50 mm even if samples had the same crystalline phase. Change was not correlated with fragmentation behavior of liquid suspension inside the plasma jet. Water content over 50 vol% was found to produce unmelted particles, indicating that water suppressed heat transfer to the particles. However, plasma jet temperature was not affected. Instead, the coating fabricated with water addition has higher oxygen and lower carbon content compared to these characteristics of the coating without water addition. This was attributed to the retarded complete evaporation of liquid media from the suspension droplet, resulting in inhibition of excessive heating and evaporation of the molten $Y_2O_3$ droplet. In this regard, crystalline phase development with respect to stand-off distance and water addition was discussed.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.2
• /
• pp.228-237
• /
• 2005

The main purpose of this study was to investigate the red water reducing effects of phosphate based inhibitor when it was applied to water distribution system. The effects of pH, alkalinity, calcium concentration in the reduction of the red water also studied. The most finished water in Korea showed relatively high corrosiveness and was required to introduce some types of corrosion reducing methods such as addition of alkalinity. The precipitation of $CaCO_3$ by addition of $Ca(OH)_2$ formed porous film on the surface of the carbon steel pipes and was displaced easily from the surface of the pipes; on the other hand, addition of zinc phosphate (ZOP) formed reliable film on the surface and reduced iron release and color. Although the main function of ZOP was to suppress the release of Pb and Cu, it also reduced iron concentration released from water distribution pipes.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.236-237
• /
• 2014

Recently, it changes to the frame construction in the wall type structure for the life span improvement of the apartment house of our country. The execution of the light panel increased while the execution of the frame construction increased. Therefore, the density and absorption ratio of the magnesium oxide matrix according to the wood flour amount of addition ratio property try to be analyze for the lightweight of the surface material of the light panel. The test result, the density has been declined as the addition ratio increase of the wood flour. In the case of the water absorption ratio, water absorption ratio has been increased as addition ratio increase of wood flour. However, wood flour addition ratio 15% determined the most appropriate when considering the density and water absorption ratio.

• Journal of the Korean Ceramic Society
• /
• v.28 no.2
• /
• pp.167-175
• /
• 1991

In synthesizing hydrated zirconia powder by hydrolysis of Zr-alkoxides using ethanol as mutual solvent, three experimental parameters, namely, concentration of alkoxides and hydrolysis water and addition rate of hydrolysis water were varied systematically. Spherical, monodispersed, nonagglomerated and submicrometer sized powders were prepared at 0.3 M of Zr(n-OPr)4 and 0.05M of Zr(n-OBu)4 with wide ranges of hydrolysis water conditions i.e. 0.5-2.0M concentration and 1-20ml/min addition rate. During the hydrolsis, careful attention have to be paid to maintain homogeneous reaction by controlling the agitation of the reactant and the addition of the hydrolysis water. For more improved condition of monodispersity it was found that the key point is to shorten the self-nucleation time within several seconds as rapid as possible. In both alkoxides system, with higher concentration of alkoxide and hydrolysis water and with slow addition rate of hydrolysis water, hydrated zirconia powders synthesized showed tendency to fall in worse powder conditions.

• Macromolecular Research
• /
• v.15 no.1
• /
• pp.10-16
• /
• 2007

In this work, we prepared epoxy/BMI composites by using N,N'-bismaleimide-4,4'-diphenylmethane (BMI), epoxy resin (diglycidyl ether of bisphenol-A (DGEBA)), and 4,4'-diamino diphenyl methane (DDM). The thermal properties and water sorption behaviors of the epoxy and BMI composites were investigated. For the epoxy/BMI composites, the glass transition and decomposition temperatures both increased with increasing BMI addition, which indicates the effect of BMI addition on improved thermal stability. The water sorption behaviors were gravi-metrically measured as a function of humidity, temperature, and composition. The diffusion coefficient and water uptake decreased and the activation energy for water diffusion increased with increasing BMI content, indicating that the water sorption in epoxy resin, which causes reliability problems in electronic devices, can be diminished by BMI addition. The water sorption behaviors in the epoxy/BMI composites were interpreted in terms of their chemical and morphological structures.

• Advances in nano research
• /
• v.14 no.1
• /
• pp.81-92
• /
• 2023

In this work, the effect of the addition of Aerosil 200, an insulating resin applied in many industries, on the water absorption of cement plast mixture has been experimentally evaluated. First, the preparation stages of cement plast mixture was evaluated based on corresponding standards and then, the effect of the addition of Aerosil 200 nanoparticles (NPs) to cement plast mixtures with sand weight percentage range of 0-0.1% on the variation of water absorption properties was evaluated based on National Standard Institution of Iran 20185 for Concrete Flooring Blocks - Requirements and Test Procedures. Based on the obtained results, it could be found that excessive addition of NPs did not affect the physical properties of the final product. Water absorption percentage was increased in the weight percentage of cement. By the increase of the amount of Aerosil 200 NPs in the prepared cement plast mixture, the percentage of water absorption in weight percentage of sand was decreased. Cement plast with NPs presented significantly lower water absorption than that without NPs.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.157-160
• /
• 2006

Recently, trouble of sand supply is occurred according to exhaustion of natural sand resources. To solve this problem, sea sand and crushed sand are used. But, necessity of water reducing agent because quality of concrete that use sea sand and crushed sand is deteriorated. Therefore in this study was examined on the engineering properties of concrete with kind of fine aggregate and addition ratio of water reducing agents. As a result, compressive strength appeared similar standard regardless of kind of fine aggregate. Compressive strength, durability was similar in decrease of the unit water content by increase of addition ratio of the water reducing agent. Also, drying shrinkage resistivity was improved because the unit water content decreased.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.30 no.3
• /
• pp.455-459
• /
• 2001

Tofu (soybean curd) was made with whole soybean flour (WSF, 420 mesh) by various processing conditions of water addition ratio, heating time, coagulation temperature, molding pressure and 0.3% of mixed coagulant (CaSO₄:GDL=50:50(w/w)). Yield content of WSF-tofu was the highest in processing condition of 85℃ coagulation temperature, 10 times water addition, 5min. heating time and 25.00 g/㎠ molding pressure. As the increase of the water addition ratio from 8 to 14 times (water:WSF, v/w), Hunter's L and a values were increased. Raising of heating time (100℃, 1, 5, 10 and 15 min), a and b value were increased. Textural properties of WSF-tofu were significantly affected by coagulation temperature (75, 80, 85 and 90℃). Hardness was increased, but adhesiveness and cohesiveness were decreased. heating time was influenced on harness of WSF-tofu, but water addition ratio was not affected on hardness of WSF-tofu. Increasing of molding pressure (16.83, 25.00, 33.22 and 41.67 g/㎠, 1 hr) was resulted from a increased hardness, gumminess and chewingss of tofu, but adhesiveness was addition ratio, 5 min heating time and 25.00 g/㎠ molding pressure recorded the highest score in sensory evaluation test.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.4 s.107
• /
• pp.67-76
• /
• 2004

Because paper industry spends lots amount of water, the recycling of water is very important in economical as well as environmental aspects. In order to optimize the process water recycling system, the efficiency of unit operation for water circulation, such as save-all system, CDS and settling tank, plays an important role in. In this study, the sedimentation efficiency of process water was evaluated by SS measurement with the different amounts of flocculent addition. 3 different kinds of process water were collected from fine paper mill, and applied in laboratory sedimentation equipment for the measurement of settling efficiency of SS materials. The addition amounts of alum and PAC were resulted in optimum efficiency of sediments in the condition of 100 ppm of alum and 500 ppm of PAC respectively. In the comparison of sedimentation efficiency between alum and PAC, alum showed more economical and efficient results. The SS of spill water and the particle size of suspended materials treated by alum flocculents were below 50 ppm and about 1 $\mu$m. It would be considered that the spill water can be substituted to superclear water grade.