• Textile Coloration and Finishing
• /
• v.20 no.3
• /
• pp.1-7
• /
• 2008

Three kinds of 135D/108F ITY were produced from raw yam 85D/72F + SDY 50D/36F with. interlacing pressure $1.5kg/cm^2$, $2.5kg/cm^2$, $3.5kg/cm^2$ respectively. 72 kinds of sized yams were manufactured from three ITYs by altering sizing speed, sizing temperature and sizing tension. The mechanical characteristics of 72 kinds of plain fabrics which were woven using the sized yam as a warp were analyzed after scouring. The initial modulus of scoured fabric responded sensitively to the sizing speed in high tension. The WT of scoured fabric recorded the. highest1n the conditions of sizing tension 30g, and air pressure $2.5kg/cm^2$ in interlacing treatment. When sizing temperature was high, the WT value appeared low, but when sizing speed was high, the WT value was much affected by air pressure in interlacing raw yam. The MIU value of fabric according to sizing tension variations increased up to sizing tension 40g, but decreased above it. The bulk density decreased up to sizing tension 30-40g, but increased above it. In addition, the bulk density decreased as sizing temperature increased.

• Textile Coloration and Finishing
• /
• v.16 no.4
• /
• pp.36-44
• /
• 2004

This research surveys the differences of fabric mechanical properties according to the different looms and the fabric positions with relation to warp and weft weaving tensions on the Picanol and Omega looms respectively. For this purpose, the grey fabrics woven in the previous paper are processed in dyeing and finishing processes, and the processing shrinkages are measured on each processes such as dryer, scouring, pre-set, dyeing and final-set using the fabric density and width. The mechanical properties of the finished fabrics are measured and discussed with relation to the warp and weft weaving tensions of the two looms and the variations of the fabric mechanical properties according to the fabric positions are also discussed. In addition, the fabric thickness according to the fabric positions such as right, left selvedges and center of the fabrics is also measured and discussed with the characteristics of the Picanol and Omega looms.

• Textile Coloration and Finishing
• /
• v.16 no.5
• /
• pp.54-61
• /
• 2004

This research surveys the differences of fabric mechanical properties with the different looms and the fabric positions according to the warp and weft yarn tensions on the Vamatex and Omega-Panter looms respectively. For this purpose, the grey fabrics woven by PET filament using two test looms are dyed and finished. The processing shrinkages are measured on each processes such as dryer, scouring, pre-set, dyeing and final-set using the fabric density and width. The mechanical properties of the finished fabrics are measured and discussed with relation to the warp and weft yarn tensions of the two looms and the fabric positions. In addition, the fabric thickness according to the fabric positions such as right, left selvedges and center of the fabrics is also measured and discussed with the characteristics of the Vamatex and Omega-Panter looms.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.1
• /
• pp.12-24
• /
• 2000

The electro-hydraulic servo winch system built in a automatic tension control equipment was designed with a latent need for an advanced system in fishing operations of the inshore and coastal fishing vessels. In order to keep the constant tension condition of warp under loading, a tension control circuit was added to the servo winch system.The dynamic performance in the open loop behaviour of the designed winch system was investigated and its applicability was tested for various possibilities of load using a load generator especially developed in order to this study.The mechanical characteristics of this system is different from that of a conventional type, that is, the tension, length, line speed and drum revolution can be automatically controlled by the information from various sensors, such as torque, rpm and pressure transducers. from the experiment results, it was verified that the servo winch system has very good output and tracking behaviour for the control input signals in different operating conditions though overshoot of out 8% in the transient characteristics of torque under the load though a overshoot of about 8% in the transient characteristics of torque under the load condition can be observed when the opening of servo valve, adjustable by the input voltage between - 10 V up to 10 V, changed suddenly.Consequently, the improved fishing winch system can be effectively used as the automatic shooting and hauling equipment of low cost for small inshore and coastal fishing vessels which engage in net fishing.

• Textile Coloration and Finishing
• /
• v.16 no.3
• /
• pp.31-38
• /
• 2004

Polyester fabrics, which is a major product in Daegu and Kyungbuk district, recently have a frequent warp streak phenomenon of sizing textiles for peach skin. So, this paper intensively focuses on the analysis of finding causes of poor products which may be produced in the process of sizing. Depending on the changes of sizing yarn's physical characteristic varying on sizing conditions, results of the research are as followed. 1. Sizing add-on rate, following tension changes of originally supplied yarn in sizing, does not fluctuate until 30g sizing tension, but marks high on the increase of sizing speed. 2. Sizing add-on amount increases approximately by 2.5% when interlacing pressure is raised from 1.5kg/$cm^2$ to 3.5kg/$cm^2$ at $130^{\circ}C$ sizing temperature. 3. Following the increase of sizing tension from 10g to 50g, boiling shrinkage rate of desizing yarn changes approximately from 7% to 11%. But the more sizing temperature and speed increases, the bigger the change rate becomes. 4. The thermal stress of desizing yarn is sensitively influenced by sizing tension in the sizing degree of above $130^{\circ}C$. 5. The deviation rate of sizing yarn's initial modulus value, which is influenced by air pressure in interlacing raw yarn, marks the highest at 40g and 50g strength.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.160-163
• /
• 1999

The mechanical properties and failure behaviour of carbon/phenolic composites were inverstigated by tension and compression. Carbon/phenolic composites were fabricated by infiltration of matrix into 8 harness satin woven fabric of PAN-based carbon fibers. The tensile and compressive tests were performed at 25℃ under air atmosphere and, at 400℃ and 700℃ under N₂ atmosphere. The tensile strengths of carbon/phenolic composites in with-laminar/0° warp direction were about 10 times higher than those in with-laminar/45° warp direction, which was analyzed due to a change of fracture mode from fiber pull-out by shear to tensile fracture of fibers. The fracture of carbon/phenolic composites in with-laminar/45° direction was analyzed due to delamination by buckling. Tensile and compressive strength of carbon/phenolic composites decreased to about 50% at 400℃, and to about 10% at 700℃ compared to that at room temperature. The main reason for the decrease of tensile or compressive strength with increasing temperature was analyzed due to a reduction of bond strength between fibers and matrix resulting from thermal degradation of phenolic resin.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.6
• /
• pp.67-74
• /
• 2008

This paper is concerned with the development of a measurement system using field measuring device which will give the membrane stress of the membrane structures. Up to this point, several techniques on measurement of membrane stresses has been proposed and some have been used in the fields, but accuracy of the measured stresses to be far from reliable one. Such situation has not been changed until recent days, we do not have the measurement device on which we can depend. On top of that, due to the different properties in cross directions for material of the membrane, the stress in the warp direction is different from that in the fill one.

• Journal of the KSME
• /
• v.35 no.1
• /
• pp.46-52
• /
• 1995

지금에 이르기까지 직기개발을 위한 주안점은 새로운 위입시스템(water-jet, air-jet)의 개발과 지속적인 직기의 생산속도증가에 대한 각 위입요소들의 최적동작을 위한 기계요소의 개발에 주 어져 있었다. 반면에 위입동작과 직접 연관되지 않는 직기의 구성요소들은 증가하는 위입속도에 따라 각 기능의 안정성과 동작의 정확성에 대한 요구가 점차 증가되었으며, 특히 경사장력 및 이에 작용하는 기계요소들에 대한 기술적 요구수준은 과거의 북직기에서의 경우에 비교될 수 없을 정도의 한계적 상황을 만족시켜야 하게 되었다. 경사송출의 경우, 위사 1가닥이 공급될 때 마다 직물권취에대응하여 경사장력을 일정하게 유지하며, 경사의 일정 길이를 정확히 공급하여야 하기 때문에 고속 무북직기에서는 빠른 응답속도와 안정된 동작을 행할 수 있는 경사송출기구 및 장력제어시스템의 성능이 직기성능에 가장 큰 영향을 미치게 되었으며 지금까지 사용되어온 기계적 송출장치로는 한계적 기술요건을 만족시킬 수 없게 되었다. 이에 따라 근자에 이르러 경사장력제어형 장력송출장치의 응용이 크게 대두되고 있다. 이 글에서는 이러한 새로운 형태의 송출장치의 개발상황과 경사장력제어에서 해결되지 못한 문제점에 대하여 다루어 보고자 한다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.9 no.1
• /
• pp.1-18
• /
• 1973

For regulating the depth of midwater trawl nets towed at the optimum constant speed, the changes in the shape of warps caused by adding a weight on an arbitrary point of the warp of catenary shape is studied. The shape of a warp may be approximated by a catenary. The resultant inferences under this assumption were experimented. Accordingly feasibilities for the application of the result of this study to the midwater trawl nets were also discussed. A series of experiments for basic midwater trawl gear models in water tank and a couple of experiments of a commercial scale gears at sea which involve the properly designed depth control devices having a variable attitude horizontal wing were carried out. The results are summarized as follows: 1. According to the dimension analysis the depth y of a midwater trawl net is introduced by $$y=kLf(\frac{W_r}{R_r},\;\frac{W_o}{R_o},\;\frac{W_n}{R_n})$$) where k is a constant, L the warp length, f the function, and $W_r,\;W_o$ and $W_n$ the apparent weights of warp, otter board and the net, respectively, 2. When a boat is towing a body of apparent weight $W_n$ and its drag $D_n$ by means of a warp whose length L and apparent weight $W_r$ per unit length, the depth y of the body is given by the following equation, provided that the shape of a warp is a catenary and drag of the warp is neglected in comparison with the drag of the body: $$y=\frac{1}{W_r}\{\sqrt{{D_n^2}+{(W_n+W_rL)^2}}-\sqrt{{D_n^2+W_n}^2\}$$ 3. The changes ${\Delta}y$ of the depth of the midwater trawl net caused by changing the warp length or adding a weight ${\Delta}W_n$_n to the net, are given by the following equations: $${\Delta}y{\approx}\frac{W_n+W_{r}L}{\sqrt{D_n^2+(W_n+W_{r}L)^2}}{\Delta}L$$ $${\Delta}y{\approx}\frac{1}{W_r}\{\frac{W_n+W_rL}{\sqrt{D_n^2+(W_n+W_{r}L)^2}}-{\frac{W_n}{\sqrt{D_n^2+W_n^2}}\}{\Delta}W_n$$ 4. A change ${\Delta}y$ of the depth of the midwater trawl net by adding a weight $W_s$ to an arbitrary point of the warp takes an equation of the form $${\Delta}y=\frac{1}{W_r}\{(T_{ur}'-T_{ur})-T_u'-T_u)\}$$ Where $$T_{ur}^l=\sqrt{T_u^2+(W_s+W_{r}L)^2+2T_u(W_s+W_{r}L)sin{\theta}_u$$ $$T_{ur}=\sqrt{T_u^2+(W_{r}L)^2+2T_uW_{r}L\;sin{\theta}_u$$ $$T_{u}^l=\sqrt{T_u^2+W_s^2+2T_uW_{s}\;sin{\theta}_u$$ and $T_u$ represents the tension at the point on the warp, ${\theta}_u$ the angle between the direction of $T_u$ and horizontal axis, $T_u^2$ the tension at that point when a weights $W_s$ adds to the point where $T_u$ is acted on. 5. If otter boards were constructed lighter and adequate weights were added at their bottom to stabilize them, even they were the same shapes as those of bottom trawls, they were definitely applicable to the midwater trawl gears as the result of the experiments. 6. As the results of water tank tests the relationship between net height of H cm velocity of v m/sec, and that between hydrodynamic resistance of R kg and the velocity of a model net as shown in figure 6 are respectively given by $$H=8+\frac{10}{0.4+v}$$ $$R=3+9v^2$$ 7. It was found that the cross-wing type depth control devices were more stable in operation than that of the H-wing type as the results of the experiments at sea. 8. The hydrodynamic resistance of the net gear in midwater trawling is so large, and regarded as nearly the drag, that sweeping depth of the gear was very stable in spite of types of the depth control devices. 9. An area of the horizontal wing of the H-wing type depth control device was $1.2{\times}2.4m^2$. A midwater trawl net of 2 ton hydrodynamic resistance was connected to the devices and towed with the velocity of 2.3 kts. Under these conditions the depth change of about 20m of the trawl net was obtained by controlling an angle or attack of $30^{\circ}$.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.1
• /
• pp.1-8
• /
• 1984

The author carried out an experiment to determine the resistance of trawl net aboard M/S Saebada, training ship of National Fisheries University of Pusan, 2,275 G/T and 3,600ps. Total tension loaded on warp were measured by the recording tension meter. Resistance of the net is estimated by subtracting the resistance of otter boards and warps from the total tension. Coefficient k and exponent n of the formula on the trawl net deduced by Koyama, $R_N=k\frac{d}{l}abv^n$ were calculated from the resistance of the net obtained. The results obtained are can be summarized as follows : 1. Six seamed net with two net pendant k=11, n=1.8 2. Eight seamed net with three net pendant k=11, n=1.8 3. Ten seamed net with three net pendant k=9, n=1.9 4. Ten seamed net with four net pendant k=9, n=1.9