• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.489-496
• /
• 1999

The safety of a structure can be improved by applying the three dimensional passive earth pressure. Because the three dimensional passive earth pressure is much larger than the two dimensional passive earth pressure and it is determined by the size(width B and height H) and the wall frictional angle of the resistant wall. Therefore, the three dimensional passive resistance behavior was studied through the model tests in sandy ground, where the size of the resistant wall and the wall frictional angle were varied. The results show that three dimensional passive earth pressure is 1.1∼3.4 times larger than that of the two dimensional value depending on the wall size and the wall friction.

• 한국철도학회논문집
• /
• 제19권6호
• /
• pp.765-776
• /
• 2016

본 연구에서는 철도 교대를 위한 표준단면을 선정하고, 선정된 단면에 대하여 토압산정방법과 내부마찰각에 따른 직배면과 가상배면에 작용하는 주동토압을 비교 분석하였다. 또한, 기존토압과 개량시행쐐기법의 토압을 이용하여 내부마찰각에 따른 교대의 외적 안정성, 부재력 및 경제성을 분석하였다. 본 연구로부터 가상배면에서의 주동토압은 직배면에서의 주동토압보다 크며, 내부마찰각이 증가함에 따라 감소한다는 것을 알 수 있었다. 기존토압(Rankine, Coulomb, 시행쐐기법) 및 개량토압(개량시행쐐기법) 모두 내부마찰각이 증가함에 따라 부재력은 크게 감소하였고, 경제성은 향상되는 것으로 평가되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.435-442
• /
• 2002

Fluid Confirmation Tests(FCT) on 1500 ground Anchors install in weathered rock were carried out to investigate upper and lower limit of elastic elongation, frictional resistant of fixed anchor body, mobilized angle between anchor body and soil. All the measured data were analysed and compared with theoretical equations. The frictional angles of diaphragm wall and anchorage system in weathered rock showed nonlinear curve between upper and lower limit of standard elongation. The FCT results indicated that the frictional resistant angles increased with higher values of surcharge load. The quality assurance on the fixed anchor location was investigated by means of measuring elastic elongation during the FCT, and comparing these with theoretical design length, the quality of anchors in this particular site found to be above average standard. The results of this research works with provide valuable guide line on quality assurance of anchors system as well as resonable prediction of friction resistance between the fixed anchor body and the weathered rock.

• Geomechanics and Engineering
• /
• 제15권4호
• /
• pp.937-945
• /
• 2018

A probabilistic study of a reinforced earth wall in a frictional soil using the surface response methodology (RSM) is presented. A deterministic model based on numerical simulations is used (Abdelouhab et al. 2011, 2012b) and the serviceability limit state (SLS) is considered in the analysis. The model computes the maximum horizontal displacement of the wall. The response surface methodology is utilized for the assessment of the Hasofer-Lind reliability index and is optimized by the use of a genetic algorithm. The soil friction angle and the unit weight are considered as random variables while studying the SLS. The assumption of non-normal distribution for the random variables has an important effect on the reliability index for the practical range of values of the wall horizontal displacement.

• 한국소음진동공학회논문집
• /
• 제12권9호
• /
• pp.717-724
• /
• 2002

In this study, a numerical analysis for the piston secondary dynamics of small refrigeration reciprocating compressors is performed. In general, the length of cylinder in this class of compressors is shortened to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder wall is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the piston dynamics, the change in bearing length of the piston and all corresponding forces and moments are considered in order to determine the piston trajectory, velocity and acceleration at each step. A Newton-Raphson procedure was employed in solving the secondary dynamic equations of the piston. The developed computer program can be used to calculate the entire piston trajectory and the hydrodynamic force and moment as functions of crank angle under compressor running conditions. The results explored the effects of the radial clearance, lubricant viscosity, length of the cylinder wall, and pin location on the stability of the piston.

• Journal of Mechanical Science and Technology
• /
• 제17권3호
• /
• pp.350-356
• /
• 2003

In this study, a numerical analysis for the piston secondary dynamics of small refrigeration reciprocating compressors is performed. In general, the length of cylinder in this class of compressors is shortened to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder wall is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the piston dynamics, the variation in bearing length of the piston and all corresponding forces and moments are considered in order to determine the piston trajectory, velocity and acceleration at each step. A Newton-Raphson procedure was employed in solving the secondary dynamic equations of the piston. The developed computer program can be used to calculate the entire piston trajectory and the lubrication characteristics as functions of crank angle under compressor running conditions. The results explored the effects of some design parameters and operating conditions on the stability of the piston, the oil leakage, and friction tosses.

• Tribology and Lubricants
• /
• 제18권4호
• /
• pp.291-298
• /
• 2002

In this study, a numerical analysis f3r the piston secondary dynamics and lubrication characteristics of small refrigeration reciprocating compressors is presented. In general, the length of cylinder in this class of compressors is shortened to diminish the frictional losses of the piston-cylinder system. So, the contacting length between piston and cylinder wall is in variable with the rotating crank angle around the BDC of the reciprocating piston. In the problem formulation of the piston dynamics, the change in bearing length of the piston and all corresponding forces and moments are considered in order to determine the piston trajectory, velocity and acceleration at each step. A Newton-Raphson procedure was employed in solving the secondary dynamic equations of the piston. The developed computer program can be used to calculate the entire piston trajectory and the hydrodynamic forces and moments as functions of crank angle under compressor running conditions. The results explored the effects of the radial clearance, lubricant viscosity, and pin location on the stability of the piston, the oil leakage, and friction losses.

• 한국지반신소재학회논문집
• /
• 제17권2호
• /
• pp.33-40
• /
• 2018

지반구조물에서는 흙과 구조물 사이의 상호 마찰 특성이 구조물에 작용하는 하중과 저항 분석에 큰 영향을 미친다. 일반적으로 지반구조물의 주재료로서 콘크리트 또는 강재가 많이 사용되며, 흙 입자 크기와 비교하여 마찰면의 거칠기 정도에 따라 경계면 마찰 특성이 큰 차이를 보인다. 특히 비신장성 보강재를 사용하는 보강토 옹벽, 말뚝 주면, 옹벽면 등의 지반구조물에 대해서는 흙과 구조물 사이의 마찰특성을 합리적으로 분석하여 구조물의 안전성을 확보하여야 한다. 구조물면과 사질토 사이의 마찰특성에 대하여 보다 정확한 예측식을 제시하고 이 예측식이 가지고 있는 불확실성을 제시하는 것은 지반-지반구조물의 신뢰성 분석에 필수적이다. 따라서 본 연구에서는 기존 양질의 연구 문헌들에 보고된 흙과 거칠기가 다른 면 사이의 마찰실험결과를 분석하여, 강재와 사질토 사이의 첨두 경계면 마찰각을 구하는 식을 제안하였다. 첨두 경계면 마찰각을 결정하는 주요인자는 경계면의 상대조도, 흙의 상대밀도, 구속압, 한계상태 경계면 마찰각이다. 본 연구에서 개발한 첨두 경계면 마찰각 예측식에 대한 불확실성을 통계적으로 Goodness-of-fit 시험 결과를 반영하여 평가하였다.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.844-853
• /
• 2003

In this paper, a dynamic analysis of the reciprocating compression mechanism of a small refrigeration compressor is performed. In the problem formulation of the mechanism dynamics, the viscous frictional force between the piston and the cylinder wall is considered in order to determine the coupled dynamic behaviors of the piston and the crankshaft. Simultaneous solutions are obtained for the equations of motion of the reciprocating mechanism and the time-dependent Reynolds equations for the lubricating film between the piston and the cylinder wall and for the oil films on the journal bearings. The hydrodynamic forces of the journal bearings are calculated by using a finite bearing model along with the Gumbel boundary condition. A Newton-Raphson procedure is employed in solving the nonlinear equations for the piston and crankshaft. The developed computer program can be used to calculate the complete trajectories of the piston and the crankshaft as functions of the crank angle under compressor-running conditions. The results explored the effects of the radial clearance of the piston, oil viscosity, and mass and mass moment of inertia of the piston and connecting rod on the stability of the compression mechanism.

• Journal of Biosystems Engineering
• /
• 제16권2호
• /
• pp.133-141
• /
• 1991

This study was undertaken to investigate the structural and configurational characteristics of the tailings return-unit in the commercially available head-feed combines and to study the aero-dynamical behavior of the tailings in the units. The mathematical model of the motion of tailings in the thrower casing was developed and the simulated trajectories for different type of units was analyzed to compare with the measured ones. The air-stream velocity profile in various locations along the tailings returning duct was measured to find the effect of configurational characteristics and blade tip speed. The results of the study are summerized as follows. 1. The ejecting angle, which is the angle between the direction of the particle velocity ejecting from the blade and the horizontal axis, was found to be about $66^{\circ}$ in both the simulation and experiment. The angle was much greater than the setting angle of actual duct of the combines studied, which were $48{\sim}56^{\circ}$. By comparison of these results, it was suggested to change duct setting angle so as to reduce the frictional force, between the duct wall and tailings, by reducing the difference between the ejecting and setting angles. 2. The velocity of the air stream in the duct was in general higher in the upper bound of the duct compared to the lower and decreased as the stream went toward the end of duct. The comparison of the tailings units among the combines studied showed a superior performance with the tapered duct having small diameter in the outlet and with greater number of thrower blade.