• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.9
• /
• pp.21-25
• /
• 2008

In this study, to maximize RF performance of MOSFETs, $f_T$ and $f_{max}$ dependent data on $W_u$ are measured and newly analyzed by extracting small-signal model parameters. From the physical analysis results, it is found that a peak value of $f_T$ is generated by $W_u$-independent parasitic gate-bulk capacitance at narrow $W_u$ and the wide width effect of reducing the increasing rate of transconductance at wide $W_u$. In addition, it is revealed that a maximum value of $f_{max}$ is caused by the non-quasi-static effect that the gate resistance is greatly reduced at narrow $W_u$ and becomes constant at wide $W_u$.

• Korean Journal of Materials Research
• /
• v.2 no.6
• /
• pp.468-476
• /
• 1992

Stress rupture properties and fracture behavior of Ni microalloyed W were studied using direct load creep tester at 100$0^{\circ}C$, 110$0^{\circ}C$ and 120$0^{\circ}C$ in $H_2$. At the same grain size, 15${\mu}$m, the 100hr. stress rupture strength of W-0.4wt% Ni was 23% higher than that of W-0.2wt%Ni due to the grain growth during test. The minimum creep rate of W-0.2wt%Ni was decreased with an increase in initial grain size. By increasing the Ni content of Ni microalloyed W, rupture time was increased owing to the smaller number and size of cavity. All the specimens showed intergranular fracture by grain boundary sliding and nucleation, growth and coalescence of cavities at grain boundary.

• Fire Science and Engineering
• /
• v.26 no.2
• /
• pp.105-111
• /
• 2012

In this research, aluminum composite panels of the general materials and fire retardant materials as building claddings make researches about fire performance comparison analysis. Test methods of the small and medium cone calorimeter experiments and SBI (Single Burning Item) experiments was applied to the determination. As a result, in the experiments peak heat release rate cone calorimeter the general aluminum composite panel $1,293kW/m^2$ ($75kW/m^2$), flame-retardant aluminum composite panel $70kW/m^2$ ($75kW/m^2$) was measured. In the SBI experiments fire growth rate the general fire aluminum composite panel is approximately 743 W/s and the flame-retardant aluminum composite panel is approximately 97 W/s of the value were measured. Thus, a standards enactment are urgently required in this case it is used as building claddings of the aluminum composite panel by fire risk assessment.

• Journal of Powder Materials
• /
• v.18 no.3
• /
• pp.226-237
• /
• 2011

W-ZrC and W-HfC composite powders were fabricated by the Plasma Alloying & Spheroidization (PAS) method and the powders were sprayed into hybrid coating layers by using Low Vacuum Plasma Spray (LVPS) process, respectively. Microstructure, mechanical properties, and ablation characteristics of the fabricated coating layers were investigated. The LVPS process led to successful production of W-Carbide hybrid coatings, approximately 400 ${\mu}M$ or above in thickness. As the substrate preheating temperature increased from $870^{\circ}C$ to $917^{\circ}C$, the hardness of the W-ZrC coating layer increased due to decreased porosity. Vickers hardness showed higher value (about 108.4 HV) in W-ZrC hybrid coating material compared to that of W-HfC while adhesive strength was found to be similar in both coating layers. The plasma torch test revealed good ablation resistance of the W-Carbide hybrid coating layers. The relatively high performance W-ZrC coating layer at the elevated temperature is thought to be attributed to both the strengthening effect of ZrC particle remained in the layer and the formation of ZrO2 phase with high temperature stability.

• Journal of Astronomy and Space Sciences
• /
• v.14 no.2
• /
• pp.347-354
• /
• 1997

We developed a GPS phase data processing S/W system which calculates baseline vectors and distances between two points located in the surface of the Earth. For this development a Double-Difference mothod and L1 carrier phase data from GPS(Global positioning System) were used. This S/W system consists of four main parts: satellite position calculation, Single-Difference equation, Double-Difference equation, and correlation. To verify our S/W, we fixed KAO($N36^{circ}.37,E127^{circ}.37,H77.61m$), one of the International GPS Services for Geodynamics, which is located at Tae-Jon, and we measured baseline vectors and relative distances with data from observations at approximate baseline distances of 2.7, 42.1, 81.1, 146.6km. Then we compared the vectors and distances with the data which we obtained from the GPSurvey S/W system, with the L1/L2 ION-Free method and broadcast ephemeris. From the comparison of the vectors and distances with the data from the GPSurvey S/W system, we found baseline vectors X, Y, Z and baseline distances matched well within the extent of 50cm and 10cm, respectively.

• Journal of Soil and Groundwater Environment
• /
• v.10 no.3
• /
• pp.46-51
• /
• 2005

This study was to evaluate sorption and biodegradation rate affecting the natural dissipation of chlorinated volatile organic compounds (CVOCs) in surface soil. To show the effect of sorption and biodegradation on the natural dissipation of 1,1,1-trichloroethane (TCA), trichloroethylene (TCE) and tetrachloroethylene (PCE), three types of vial experiments were employed; (1) sterilized, (2) non-sterilized, (3) non-sterilized/substrate enriched. Also three moisture contents was applied to find the moisture effect in each vial; (1) wilting point (12%, w/w), (2) field capacity (29%, w/w), (3) saturation (48%, w/w). The results suggested that keeping the soil moisture content at field capacity was desirable for TCA and TCE natural dissipation in the vial study.

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.308-317
• /
• 1993

The study is related to the synthesis of acrylic acid by selective oxidation of acrolein on Mo-V-W multicomponent mixed oxide catalysts. Mo-V-W-O(WVM), Mo-V-O/Mo-W-O(VM/WM), Mo-W-O/Mo-V-O(WM/VM) and mechanical mixtures of Mo-V-O and Mo-W-O(M-VM+WM) were prepared and characterized by BET, XRD, SEM and EPMA. Catalytic activity of these catalysts was tested in a continuous fixed bed reactor. In WVM catalysts small amount of tungsten added to VM increased surface area and selectivity of acrylic acid, but excess amount of tungsten decreased reaction rate of acrolein and selectivity. VM/WM catalysts, VM supported on WM, showed higher activity and selectivity than WM/VM catalysts where WM is supported on VM. Phase cooperation between WM and VM was observed in mechanical mixture of WM and VM and they showed higher yield than WM or VM.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.177-183
• /
• 1991

Change of the properties of selective CVD-W by $SiH_4$ reduction with the variation of deposition time and pressure has been investigated. The lime required for covering the who)to Si substrate by tungsten at $300^{\circ}C$ under the pressure of 100mtorr is approximately 30 seconds. The film thickness tends to increase linearly in the early stage of deposition process and parabolically later, sheer resistance of the film tends to decrease rapidly initially, and slowly later with deposition time. Tungsten grain size does not change much, but grain boundary becomes hazy in the pressure range of 50-300mtorr. Also no ${\beta}-W$ but only ${\alpha}-W$ was found in this pressure range. The deposition rate and electrical resistivity of tungsten tend to increase wish increasing pressure. The results of AES analysis show that pressure does not much affect Si/W ratio of the tungsten film and silicidation at the W/Si interface.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.36-36
• /
• 2002

최근 한국기계연구원에서 개발된 Mechanochemical process (MCP)는 Spray conversion 법에 의하여 나노크기의 W/Cu 복합 분말을 제조하는 방법으로서, 현재 (주)나노테크에서 산업화를 위한 시험/개발이 진행 중이다. 이 방법에 의하여 W /1 0 ~ 40wt. %Cu 조성의 초미렵 W/Cu 복합 분말의 양산화가 가능하게 됨으로써, 나노복합분말을 사용한 초미립 W/Cu 합금의 소결 제조 연구 역시 나 노태크에서 분말사업화와 동시에 수행되고 있다. 현재 Spray conversion 법으로 제조되고 있는 W/Cu 나노복합분말 및 그 소결체는 Cu의 조성범 위에 따라 민수용 및 군수용 제품으로의 적용이 시도되고 있으며, 각기 특성향상을 목표로 각 적용 분야에서 요구되는 제반 성능에 대한 검토가 이루어지고 있다. 특히 군수용의 목적으로 사용될 경우, 정적 및 동적부하상태에서 재료의 균일한 변형이 가장 중요한 특성이다. 현 개발품의 경우, 일반 W 빛 Cu 원료에 비하여 상대적으로 높은 순도의 원료를 사용하였기 때문에 분말 및 소재상태 에서의 순도가 높아서, 연성을 저하시키는 것으로 알려진 기지상내 합금원소 또는 interface 게재물 이 존재할 가능성이 매우 낮다. 또한 초미립 W 입자들과 Cu 상의 혼합도가 극대화된 상태이기 때문에 상대적으로 저옹에서도 완전치밀화된 미세조직을 얻을 수 있는데, 이는 분말상태의 균일한 미세구조를 유지할 수 있으며, 동시에 W 업자간의 과도한 neck 형성을 방지함으로써 기계적 변형시 재료의 연성 향상이 기대된다. 이러한 W/Cu 나노복합분말 소결체의 특성은 균일한 밀도분포와 동시에 과도한 동적 부하상태에서 균일한 변형이 보장되어야만 하는 특정 군수용 목적에 잘 부합하는 것으로 판단된다. 본 고에서는 상기한 W/Cu 나노복함분말을 사용하여 균일한 미세구조를 가지는 완전치밀화된 소결재를 제조하는 과정과 제조된 소결재를 향후 군수용 제품에 척용시키기 위하여 진행된 단조특성에 대한 연구결과틀을 재료의 미세구조척 관점에서 논의하였다.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.4
• /
• pp.319-323
• /
• 1991

To determine how closely related to field lodging for several characters affecting the field lodging for several characters affecting field lodging, and to obtain the basic information for selection of lodging resistance genotype, an experiment was conducted with 10 varieties from May to Oct., 1990 at the experimental field in Sunchon Xational University. Culm length, dry weight per unit culm length (W/1), bending moment per unit culm diameter (W1/d), lodging index (L), bending load ratio (W1/P), and index of critical lodging load(W$_{s}$$^{2}$/1$^4$) were the most closely related characters to field lodging. Culm length showed highly significant positive correlation coefficient with field lodging(r=0.7607), but it may be undesirable to judge lodging resistance of genotype by culm length itself without consideration of culm stiffness. Considering the difficulty and time-consuming to measure the character, clum length, W/1, W1/d, and W$_{s}$$^{2}$/1$^4$ were easy to measure and hence would be the most useful variables to judge the lodging resistance of genotype. Culm diameter, cross sectional area of culm, thickness of culm wall, and the second inertia moment of cross section of culm were not correlated with field lodging at all. Breaking strength of culm showed significantly negative correlation coefficient (r=-0.3986) with field lodging.ing.