• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.132-135
• /
• 2004

High-performance concrete (HPC) may be expected to differ from usual concrete with respect to shrinkage behavior, and it shows high autogenous shrinkage due to the use of very low water-binder ratio (w/b) and various admixtures. Therefore, in order to minimize the shrinkage stress and to ensure the service life of concrete structure, volumetric change of HPC should be understood. In this study, small prisms made of HPC with w/b of 0.32 and blast-furnace slag content of $0\%,\;30\%,\;and\;50\%$ were prepared to measure the volumetric changes such as autogenous shrinkage, drying shrinkage, and swelling under three different curing conditions. It was observed that the concrete cured. sealed condition showed only autogenous shrinkage while the concrete let to dry condition at temperature of $20^{\circ}C$ and relative humidity of $60\%$ during the test period showed both autogenous and drying shrinkage. Moreover, the concrete exposed to dry condition after 2-day water curing swelled and then started to shrink with age. The total shrinkage (autogenous+drying) of this concrete was smaller than that of the concrete cured dry condition, especially at early-age. Therefore, the early-age moisture curing is very effective to control or minimize the volumetric change and its induced stress of HPC.

• Restorative Dentistry and Endodontics
• /
• 제28권6호
• /
• pp.457-466
• /
• 2003

The aim of study was to investigate the effect of flow, specimen geometry and adhesion on the measurement of linear polymerization shrinkage of light cured composite resins using linear shrinkage measuring device. Four commercially available composites - an anterior posterior hybrid composite Z100, a posterior packable composite P60 and two flowable composites, Filtek flow and Tetric flow-were studied. The linear polymerization shrinkage of composites was determined using 'bonded disc method' and 'non-bond-ed' free shrinkage method at varying C-factor in the range of 1∼8 by changing specimen geometry. These measured linear shrinkage values were compared with free volumetric shrinkage values. The viscosity and flow of composites were determined and compared by measuring the dropping speed of metal rod under constant load. In non-bonded method, the linear shrinkage approximated one third of true volumetric shrink-age by isotropic contraction. However, in bonded disc method, as the bonded surface increased the linear shrinkage increased up to volumetric shrinkage value by anisotropic contraction. The linear shrinkage value increased with increasing C-factor and approximated true volumetric shrinkage and reached plateau at about C-factor 5∼6. The more flow the composite was, reduced linear shrinkage was measured by compensation radial flow.

• 한국가구학회지
• /
• 제27권1호
• /
• pp.43-48
• /
• 2016

PEG (Polyethylene glycol) impregnation in wood reduces the occurrence of checking during kiln drying. The volumetric shrinkages of wood PEG impregnated by pressure (PEG-P) or soaking (PEG-S) methods, and oven-dried by vent (VD) or air-tight (AD) methods were measured and compared with the controls. The average oven-dry weight of PEG impregnated specimens was larger than that of the controls by 3.6 g, but was not influenced by the drying methods. The average of the total volumetric shrinkage of PEG-P-VD specimens was the least (2.3%), while that of CON-S-AD specimens was the largest (28.9%). Within a drying method the total volumetric shrinkage of the control was the largest followed by PEG-S and PEG-P specimens, which implied that residual PEG in wood restrained its shrinkage during drying.

• 폴리머
• /
• 제28권4호
• /
• pp.321-327
• /
• 2004

2,2 bis 〔4-(2-hydroxy-3-methacryloyloxypropoxy)phenyl〕propane을 기본 단량체, triethylene glycol dimethacrylate를 희석제로 포함하고 있는 고분자계 치아 수복재는 중합 수축률에서의 문제점으로 인하여 사용에 제약을 받아오고 있다. 본 연구에서는 기존 고분자계 치아 수복제의 문제점인 중합 수축률을 감소시키기 위해 중합시 부피 팽창이 기대되는 비대칭 스파이로 오쏘카보네이트를 합성하고, 이를 포함하는 새로운 치아 수복재를 제조하여 이의 특성을 시험하였다. 스파이로 오쏘카보네이트를 포함하는 새로운 치아 수복재의 중합 수축율은 약45% 감소하여 우수한 체적 안정성을 나타내었다. 그러나 새로운 치아 수복재의 중합특성, 기계적 물성 등은 기존 치아 수복재에 비해 다소 저하되었다.

• 한국가구학회지
• /
• 제19권4호
• /
• pp.294-299
• /
• 2008

Collapse is an abnormal shrinkage resulting in uneven, rough surfaces and/or warping of sawn timber. The maximum abnormal shrinkages of the oak and persimmon specimens were obtained by the quasi-equilibrium drying and were compared with the other drying methods. The effect of steaming and freezing treatments on the shrinkage of wood was also investigated. The Quasi-equilibrium drying used in this study was proved as a good tool to make the maximum abnormal shrinkage of wood. The maximum abnormal volumetric shrinkage possibly caused by collapse could be 16.3% and 14.3% for the oak and persimmon specimens, respectively. In general the steaming-treated specimens shrank less than the controls for the oak specimens, but did more for the persimmon specimens. The volumetric shrinkages of the freezing-treated specimens were more various between the drying methods than those of the control and steaming-treated specimens.

• Restorative Dentistry and Endodontics
• /
• 제26권2호
• /
• pp.134-140
• /
• 2001

The polymerization shrinkage of composite resins is an important drawback although the composites have many advantages-more esthetic and conservative than metallic restoratives etc. The purposes of this research were to develop a new measurement method and to manufacture an instrument that can measure the initial dynamic volumetric shrinkage of composite resins during polymerization. The instrument was basically an electromagnetic balance that constructed with a force transducer using position sensitive photo detector(PSPD) and a negative feedback servo amplifier of proportional-derivative(PD) controller. The volumetric change of composites during polymerization was detected continuously as buoyancy change in distilled water by means of Archimedes's principle. It was converted to continuous electrical voltage signal in real time. The signal was properly conditioned and filtered and then it was stored in computer by a data acquisition(DAQ) board. By using this electronic instrument. the dynamic patterns of the polymerization shrinkage of eight commercial(Z-100, DenFil, AeliteFil, Z-250, P-60, SureFil, Synergy compact, and Tetric ceram) composite resins were measured and compared. The results were as follows. 1. From this project of developing instrument, the ability has been achieved that can acquire and process data of electrical signal transformed from various physical phenomenon by using temperature, displacement. photo. and force transducer. As a consequence, the instrumentation and measurement system used to analyze the physical characteristics of various dental materials in dental research field can be designed, manufactured and implemented in lab. 2. This instrument has some advantages. It was insensible to temperature change and could measure true dynamic volumetric shrinkage in real time without complicated process. It showed accuracy and high precision results with small standard deviation. 3. The polymerization shrinkage of composites was significantly different between brands and ranged from 2.47％ to 3.89％, The order of polymerization shrinkage was as follows, in order of increasing shrinkage, SureFil, P60, Z250, Z100, Synergy compact. DenFil, Tetric ceram, and AeliteFil. 4. The polymerization shrinkage rate per unit time, dVol％/dt, showed that the instrument can provide an indirect research method for polymerization reaction kinetics.

• 한국기계가공학회지
• /
• 제9권2호
• /
• pp.60-65
• /
• 2010

Injection molding process is one of the popular manufacturing methods to produce plastic parts with high efficiency and low cost. The tub-drum for drum type washer is made by an insert injection molding process with aluminum alloy insert of windmill type and has a big and complex structure consisted of many ribs to sustain the strength. In this paper, the volumetric shrinkages of rib part and bottom part surrounded by a windmill type insert are analyzed according to the vertical and circumferential direction of tub-drum. Volumetric shrinkage and its difference according to the height or radius of tub drum inform the designer to reduce the warpage of tub drum, and the optimal design of tub drum can be done from the those results. The change of volumetric shrinkage according to packing pressure is also analyzed. It is very important to analyze the volumetric shrinkage of tub drum because it generates the wearing phenomena at the rotating part connected to an aluminum alloy insert due to the warpage of tub drum.

• 한국건축시공학회지
• /
• 제4권2호
• /
• pp.81-88
• /
• 2004

The purpose of this study is to investigate the chemical shrinkage and autogenous shrinkage of high strength cement paste and silica fume and fly ash and sand to cement ratio by the method of volumetric tests, and also investigate the autogenous shrinkage of high measurement method, and compare the results of volumetric test and linear length measurement test. A series of cement paste which have W/C ratio of 25%, 35%, 45% respectively were planed to study the effect of the W/C ratio to the shrinkages, and a series of cement paste which were replaced the cement by the silica fume and fly ash with 5%, 10%, 15% as the mass of cement respectively were planed to investigate the effects of poazolana to the shrinkages. A series of mortar which have a C/S ratio of 1:1, 1:1.5, 1:2 respectively were planed to investigate the shrinkage resistant effect of aggregate.

• 한국기계가공학회지
• /
• 제10권6호
• /
• pp.70-76
• /
• 2011

This paper presents an optimization procedure for reducing warpage of injection molded part by using a volumetric shrinkage deviation as an objective function. A design of experiments based on orthogonal arrays was used in the optimization procedure, and the entire optimization was performed through a two stage process - a preliminary experimentation and a principal experimentation. Proposed optimization method was applied to the design of a CPU-base part in computer. With the moderate number of experiments, an optimal molding condition for uniform distribution of volumetric shrinkage was obtained, as a result, the warpage of the molded part was significantly reduced.

• Journal of the Korean Wood Science and Technology
• /
• 제37권3호
• /
• pp.231-238
• /
• 2009

우리나라에서 전통주택(한옥) 및 목조건축 문화재의 구조부재로 많이 이용되는 소나무는 천연건조가 일반적이어서 건조에 많은 시간이 소요되고 건조가 불충분하면 수축에 의한 갈라짐 및 변형 등의 결함을 일으킬 수 있다. 소나무 소시험편과 대단면 시험편을 제작하여 함수율상태에 따른 수축률변화를 검토하였다. 특정 함수율 상태에서의 체적수축률을 예측할 경우, 생재상태에서 기건상태, 기건상태에서 전건상태까지의 구간으로 나누어 적용하는 것이 정밀도가 높았다. 변재의 체적수축률은 단면크기에는 상관성이 없으며, 심재는 단면이 커질수록 체적수축률이 감소하는 것으로 나타났다.