• 한국지반공학회논문집
• /
• 제24권1호
• /
• pp.51-59
• /
• 2008

본 연구에서는 모래에서 점토에 이르는 넓은 범위의 혼합시료를 재성형하기 위하여 세립분으로 활성을 가지고 있는 자연점토와 조립분으로 규사를 혼합하여 실험에 이용하였다. 공시체는 세립분함유율이 낮은 범위 즉, 모래입자가 골격구조를 형성하고 있는 범위에 대해서는 다양한 간극비를 조성하기 위해 습윤 다짐방법을 이용하였으며, 활성을 나타내는 범위에 대해서는 정규압밀점토의 일정한 간극비를 조성하기 위해 예압밀방법을 이용하여 다양한 세립분함유율을 갖는 공시체를 제작하여 비배수 반복 전단실험을 수행하였다. 실험결과, 세립분함유율 20%미만의 시료에서 동일한 세립분함유율의 공시체에 대해 모래 골격간극비가 증가함에 따라 반복 전단강도는 감소하였으며 더욱이, 실험시료의 골격간극비가 규사의 최대간극비 이상의 범위에서는 흙의 구조가 다짐에너지의 영향을 거의 받지 않고 강도발현의 주체가 점토 매트릭스에 지배되는것을 알 수 있다. 모래점토 혼합토를 대상으로한 비배수 반복 전단실험에서 세립분 함유율이 20%미만의 낮은 영역에서 조립자의 구조는 반복 전단강도 특성에 큰 영향을 미치며 더욱이, 세립분함유율보다 모래구조의 밀도에 유의하는것이 더욱 적합한 것을 알 수 있다.

• 한국지반공학회논문집
• /
• 제24권11호
• /
• pp.79-89
• /
• 2008

본 연구에서는 낙동강 유역에 분포하는 모래와 실트를 대상으로 실트 함유량에 따른 모래의 비배수 반복전단강도 특성을 파악하기 위하여 이방압밀비($K_c$=1.0, 1.5, 2.0)를 달리하여 일련의 비배수 반복삼축시험을 실시하였다. 시험결과 모든 $K_c$에서 실트 함유량이 증가함에 따라 반복전단응력비(CSR)가 감소하였으며, $K_c$가 증가할수록 실트 함유량 증가에 의한 CSR의 감소가 더 크게 나타났다. 전단시 발생되는 과잉간극수압은 $K_c$에 관계없이 실트 함유량 증가에 따라 초기 과잉간극수압이 크게 발생되어 CSR의 감소에 영향을 미쳤으며, 또한 압밀 후 시료의 skeleton 간극비를 산정하여 분석한 결과 실트 함유량 증가에 비례하여 전반적으로 skeleton 간극비가 크게 증가하여 초기 과잉간극수압의 증가와 더블어 CSR 감소의 주요원인으로 파악되었다.

• 산업기술연구
• /
• 제25권A호
• /
• pp.39-47
• /
• 2005

Air void systems in hardened concrete has an important influence on concrete durability such as freeze-thaw resistance, water permeability, surface scaling resistance. Linear traverse method and point count method described at ASTM are the routine analysis of the air void system that have been widely used to estimate the spacing factor in hardened concrete. Recently, many concretes often have a spacing factor higher than the generally accepted $200-250{\mu}m$ limit for the usual range of air contents. This study is proposed to estimate the plane spacing factor by calculation of simplicity. The plane spacing factor need two parameters that are air content and numbers of air voids in the hardened concrete. Those obtained from the standard air-void system analysis of the ASTM C 457. The equation is valid for all values of paste-to-air ratio because the estimation of paste content is unnecessary at the using ASTM C 457. The plane spacing factor yields a similar estimate of the standard spacing factor.

• 콘크리트학회논문집
• /
• 제12권1호
• /
• pp.33-44
• /
• 2000

Since the mechanism of chloride diffusion and its ratio in concrete depend on structural conditions and concrete as a micro-structure, if these are analyzed quantitatively, the long-term ageing of structures can be predicted. Although, a quantitative analysis of concrete micro-structure, in which the results are affected by various parameters, is very difficult, this can be done indirectly by the durability test of concrete. In this study, the compressive strength, void ratio and air permeability of concrete. In this study, the compressive strength, void ratio and air permeability of concrete are chosen as the parameters in concrete durability test, and these effects on test results are analysed according to changes of mixing properties. The relationships between parameters and chloride diffusion velocity is used for prediction models of chloride diffusion. The developed prediction models for the chloride diffusion according to mixing and physical properties, can be used to estimate the service life and corrosion initiation of reinforcing bars in marine structures.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.489-492
• /
• 2003

The results of an experiment on the sound absorption of the porous concrete and its influence on the compressive strength are reported in this paper. Two different sizes of coarse aggregate of 5~13, 13~20mm, and the design void ratio of 20, 25 and 30 percent for a given size of aggregate were used. In the compressive strength, an aggregate of the size of 5~13mm is much higher strength than that of the 13~20mm, In the sound absorption experiment, the size of aggregate of 5~l0mm is much higher sound absorption than that of the 13~20mm. The sound absorption ratio was increased as the design void ratio. As a result, Porous concrete sufficiently have the performance of sound absorption.

• 농업과학연구
• /
• 제37권3호
• /
• pp.491-499
• /
• 2010

This study was carried out to investigate the consolidation characteristics of the remolded clay by the oedometer and the constant rate of strain(CRS) consolidation tests. As the rate of strain increases, the settlement rapidly decreased. As the ratio of the sand in the specimen increases, its effect on the rate of strain to the settlement was reduced. As the effective stress increased, the void ratio decreased, while the rate of strain increased, it did not show a clear variation. The reduction of the void ratio was shown to be less than the oedometer test. The coefficient of vertical consolidation with effective stress showed very large variation around preconsolidation stress, but the rate of strain did not provide significant effects. The rate of strain with effective stress gradually decreased at all tests and mixed ratio of sand. The rate of strain at the constant rate of strain tests showed smaller than in the oedometer test. The coefficient of consolidation at the constant rate of strain tests showed much more increase than in the oedometer test. The ratio of the vertical coefficient of consolidation by the odometer and the constant rate of strain tests showed a large difference according to various tests method and mixing ratio. Therefore, it is recommended that careful attention should be paid to designing the soft ground improvement.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1877-1889
• /
• 1992

본 연구에서는 업셋팅의 변형해석 및 온도해석(열전달 해석)을 비연계 방식으 로 동시에 해석하고 실제 공정에 가깝게 접근하는 축대칭 열점소성 유한요소 프로그램 을 이용하여, 시뮬레이션에 의해 공정을 해석하여 불량감소 및 원가절감을 위해 단조 공정을 개선하는 것이다. 업셋팅공정의 연구에 있어서는 대형강괴의 주 불량요인인 기공의 소멸을 위한 공정방안을 연구하는데 있다.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.148-152
• /
• 2016

The main goal was to evaluate effectiveness of a modified TSE sequence compared with DIR (double inversion recovery) sequence in acquisition of fast flow brain vessel images using signal void effect. 32 healthy volunteers (10 men and 22 women; mean age of 31 years; ranging between 28-43 years) who underwent black blood DIR sequence (group A) and the modified TSE sequence (group B) were enrolled in our study. Signal to Noise Ratio (SNR) and Contrast to Noise Ratio (CNR) of the internal carotid arteries' lumen were compared in T1 and T2 weighted images for both group A and B. The images obtained from group B showed lower SNR values in internal carotid artery than the group A in both of the T1 and T2 weighted images (11.49% and 13.66% respectively). While the CNR values were higher in the group B than the group A in both of the T1 and T2 weighted images (8.69% and 7.55 % respectively). The qualitative score of all categories were not significantly different between the two groups. Furthermore approximately 49% of the total scan time was reduced from group B. Our study is to shorten the scanning time and minimize the inconveniences of the patients in acquisition of the black blood images of brain by using the signal void effect in the modified TSE technique while keeping the diagnostic value of the test.

• Geomechanics and Engineering
• /
• 제11권5호
• /
• pp.713-723
• /
• 2016

Shear wave velocities of three selected sandy soils subject to drained triaxial compression test were continuously measured using the bender elements. The shear wave velocity during isotropic compression, as widely recognized, increased as confining pressure increased and they were correlated well. However, during drained shearing, the mean effective stress could no further provide a suitable correlation. The shear wave velocity during this stage was almost constant with respect to the mean effective stress. The vertical stress was found to be more favorable at this stage (since confining stress was kept constant). When sample was attained its peak stress, the shear wave velocity reduced and deviated from the previously existed trend line. This was probably caused by the non-uniformity induced by the formation of shear band. Subsequently, void ratios computed based on external measurements could not provide reasonable fitting to the initial stage of post-peak shear wave velocity. At very large strain levels after shear band formation, the digital images revealed that sample may internally re-arrange itself to be in a more uniform loose stage. This final stage void ratio estimated based on the proposed correlation derived during pre-peak state was close to the value of the maximum void ratio.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.77-82
• /
• 2004

The effect of bonding condition on tensile properties of joints diffusion bonded spheroidal graphite cast iron, FCD60 to Cr-Mo steel, SCM 440 was investigated. Diffusion bonding was performed with various temperatures, holding times, pressures and atmospheres. All tensile specimens were fractured at the bonding interface. The tensile strength and elongation was increased with increasing bonding temperature. Especially, tensile strength of joints bonded at 1123K was higher than that of a raw material, FCD60, and tensile strength of joints bonded at 1173K was equal to that of a raw material, SCM440, but elongation of all joints was lower than those of raw materials. There was little the effect of holding time on the tensile properties. In comparison with bonding atmosphere, the difference of tensile strength was not observed, but elongation of joint bonded at vacuum(6.7mPa and 67mPa) was higher than that of Ar gas. Higher the degee of vacuum, elongation increased. Tensile properties of diffusion bonds depended on microstructures of cast iron at the interface and void ratio. Microstructures of cast iron at interface changed with temperature, because decarburizing and interdiffusion at the interface occurs and transformation of austenite-1 ferrite + graphite occurs on the cooling process. The void ratio decreased with increasing temperature, especially, effected on the elongation.