• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.58-68
• /
• 2009

In this study, rheological properties of ternary system cement containing ground fly ash(F3, Blaine specific surface area $8,100\;cm^2/g$) were investigated using mini slump, coaxial cylinder viscometer and conduction calorimeter. In the results, the segregation resistance was observed at high W/B and PC area while the replacement ratio of F3 was increasing. The 2:5:3 system was shown in higher fluidity and lower hydration heat than 3:4:3 system. The segregation range of cement pastes occurred over 175 mm in average diameter by mini slump and below $10\;dynesec/cm^2$ of the plastic viscosity or below 50 cP of the yield stress by coaxial cylinder viscometer. It was observed that even if BFS and FA blended together admixture properties would remaine as they were separately. The properties of admixture would not be changed. On the above results, the decreased replacement ratio of OPC and increased replacement ratio of admixtures would be possible.

• 대한기계학회논문집B
• /
• 제24권9호
• /
• pp.1277-1284
• /
• 2000

To enhance heat transfer characteristics of water, micro-encapsulated octadecane of about $10{\mu}m$ diameter was added to water. Viscosity of the slurry was measured by using a capillary tube viscometer. The measured viscosity decreased as the temperature of the slurry increased, and it increased as the fraction of the capsules in the slurry increased. Thermal characteristics of the octadecane were studied by using a differential scanning calorimeter. The melting temperature and the melting energy of the octadecane were found to be $28.6^{\circ}$ and 34.4kcal/kg, respectively. The convective heat transfer characteristics of the slurry were investigated in a flow loop with a constant heat flux test section. Friction factor of the slurry flow was found to be similar to the expected curve by Petukhov. The Nusselt number of the slurry flow was highest when the octadecane melted. Effective thermal capacity of the 14.2% slurry was found to have 1.67 times of the thermal capacity of water.

• Korea-Australia Rheology Journal
• /
• 제15권3호
• /
• pp.117-124
• /
• 2003

Elastohydrodynamic lubrication (EHL) film is measured under the condition of viscosity index improver added to base oil. In-situ optical contact method using the interference principle make the measuring resolution of ~5 nm possible and enables the measuring range all over the contact area of up to ~300 $\mu\textrm{m}$ diameter. What is more important to the developed method by the author is that the measurement of EHL film thickness is possible in the range from 100 nm to 2 $\mu\textrm{m}$, which is the regime of worst contact failures in precision machinery. Viscosity index improver (VII) is one of the major additives to the modem multigrade lubricants for the viscosity stability against temperature rise. However, it causes shear thinning effects which make the film thickness lessened very delicately at high shear rate (over $10^5 s^{-1}$) of general EHL contact regime. In order to exactly verify the VIIs performance of viscosity stability at such high shear rate, it is necessary to make the measurement of EHL film thickness down to ~100 nm with fine resolution for the preliminary study of viscosity control. In this work, EHL film thickness of VII added lubricant is measured with the resolution of ~5 nm, which will give very informative design tool for the synthesis of lubricants regarding the matter of load carrying capacity at high shear rate condition.

• 한국전기전자재료학회논문지
• /
• 제25권5호
• /
• pp.361-365
• /
• 2012

A bolt-clamped ultrasonic viscometer was designed and fabricated using a pair of ring-shaped piezoelectric ceramic resonators. For its compactness and low operation frequencies, simulation of piezoelectric resonators was carried out using an ATILA program. Ring-shaped resonators using $0.05Pb(Mn_{1/3}Sb_{2/3})O_3-0.95Pb(Zr_{0.475}Ti_{0.525})O_3$ ceramics were prepared by a conventional ceramic processing, which were then clamped with a pair of metal caps. The fabricated sensor module with a small volume of less than 1 $cm^3$ and an operation frequency as low as 26.5 kHz showed a good relationship between its quality factor and the viscosity of oil.

• 한국산학기술학회논문지
• /
• 제14권8호
• /
• pp.4028-4032
• /
• 2013

폐타이어 재활용을 위한 열분해 공법으로 발생하는 열분해 카본블랙의 재활용 방안이 필요하다. 아스팔트 바인더의 소성변형 특성을 개선하기 위하여 페타이어 열분해 공법의 부산물인 카본블랙을 이용하였다. 원아스팔트에 열분해 카본블랙 0%, 5%, 10%, 15% 및 20%를 혼합하였고, 연화점, 침입도시험, 회전점도계 및 동적전단유동기시험을 시행하였다. 열분해 카본블랙을 혼합한 아스팔트 바인더의 연화점은 증가하였고, 인화점은 기준값을 만족하였다. 135도에서의 회전점도값은 증가하였고, 소성변형에 대한 저항성이 개선되는 것으로 나타났다.

• Elastomers and Composites
• /
• 제34권5호
• /
• pp.399-406
• /
• 1999

Polytetramethylene ether glycol (PTMG)와 4,4'-diphenylmethane diisocyanate (MDI), toluene 2,4-diisocyanate(TDI), isophoron diisocyanate(IPDI)로 polyurethane (PU) prepolymer를 합성하고, dimethylol propionic acid(DMPA)로 쇄연장시킨 후 triethyl amine(TEA)으로 중화시켜서 안정한 수분산성의 음이온성 폴리우레탄을 제조하였다. 음이온성 폴리우레탄의 합성과정에서 쇄연장제의 함량과 중화비에 따른 에멀젼의 유화안정성, 접착강도, 점도, 유리전이온도 및 cast film의 물리적 성질을 UTM, Viscometer와 DSC를 사용하여 검토하였다.

• Elastomers and Composites
• /
• 제33권3호
• /
• pp.177-184
• /
• 1998

Polytetramethylene ether glycol(PTMG)와 4,4'-diphenylmethane diisocyanate(MDI), tol-uene 2,4-diisocyanate (TDI), isophoron diisocyanate(IPDI)로 polyurethane(PU) prepolymer를 합성, n-methyl-diethanol amine(n-MDEA)로 쇄연장시킨 후 glycolic acid(GA)로 quaternization시켜서 안정한 수분산성의 양이온성 폴리우레탄을 제조하였다. 양이온성 폴리우레탄의 합성과정에서 쇄연장제의 함량과 quaternization에 따른 에멀젼의 유화안정성, 접착강도, 점도, 유리전이온도 및 cast film의 물리적 성질을 UTM, Viscometer와 DSC를 사용하여 검토하였다.

• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.429-433
• /
• 2012

Purpose: While rapeseed oil, soy bean oil, palm oil and waste cooking oil are being used for biodiesel, the viscosity of them should be lowered for fuel. The most widely used method of decreasing the viscosity of vegetable oil is to convert the vegetable oil into fatty acid methyl ester but is too expensive. This experiment uses ultrasonic energy, instead of converting the vegetable oil into fatty acid methyl ester, to lower the viscosity of the waste cooking oil. Methods: For irradiation treatment, the sample in a beaker was irradiated with ultrasonic energy and the viscosity and temperature were measured with a viscometer. For heating treatment, the sample in a beaker was heated and the viscosity and temperature were measured with a viscometer. Kinematic viscosity was calculated by dividing absolute viscosity with density. Results: The kinematic viscosity of waste cooking oil and cooking oil are up to ten times as high as that of light oil at room temperature. However, the difference of two types of oil decreased by four times as the temperature increased over $83^{\circ}C$. When the viscosity by the treatment of ultrasonic energy irradiation was compared to one by the heating treatment to the waste cooking oil, the viscosity by the treatment of ultrasonic energy irradiation was lower by maximum of 22% and minimum of 12%, than one by the heating treatment. Conclusions: Ultrasonic energy irradiation lowered the viscosity more than the heating treatment did, and ultrasonic energy irradiation has an enormous effect on fuel reforming.

• 공업화학
• /
• 제25권4호
• /
• pp.357-362
• /
• 2014

본 연구에서는 높은 은폐력과 선명한 색상을 나타내는 diketopyrrolopyrroles (DPP) red 254 안료를 제조하기 위하여 미리 합성한 DPP red 254 crude를 용매 열처리 온도, 유도체 첨가 또는 볼밀링 조건들이 조합된 용매 열처리 공정을 통하여 얻어진 시료들의 물성을 비교 분석하였다. 시료의 특성은 FT-IR, UV-Vis 분광기, TEM, PSA, BET surface area analyzer, viscometer 및 spectrophotometer를 이용하여 분석하였다. 합성한 DPP red 254 crude를 볼밀링 나노화하고 용매 열처리하는 방법이 매우 효과적인 안료화 공정임을 확인하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 추계 학술논문 발표대회
• /
• pp.57-61
• /
• 2005

Cement paste is originally the basic material and crucial factor consisting concrete. This study investigates the relationship between flow apparatuses, which are ring flow(R-F), flow cone(F-C) and mini slump(M-S), in order to estimate the fluidity of cement Paste. For quantitatively evaluating the measured data this study also investigated the calibration of the rheology consistent, such as yield value and plastic viscosity, of cement paste using viscometer For this purpose the present work discussed the influence of 3 type of ordinary portland cement with different companies, affecting the fluidity of cement paste. and it also demonstrated the influence of the various kinds of mineral admixtures, such as fly ash(FA), blast furnace slag(BS) and silica fume(SF) and that of incorporating ratio. The author concluded that using R-F apparatus is the most effective flow test method of cement paste and it is exactly proportional to other apparatus' rheological properties.