• Journal of the Korean Institute of Navigation
• /
• v.13 no.2
• /
• pp.23-36
• /
• 1989

Marine casualities in the high sea are mainly classified into the breakage of hull and capsize , of which the latter occurs frequently to a small craft and container vessels by extreme rolling. The aim of this study is to develop shiphandling techniques for the prevention of ship's large rolling by way of evaluating dangerous degree of rolling in heavy weather. In this study, rolling motion is analized by using statistical method as follow : (1) 8 sample ships is presented for calculation. (2) Analized sea state are Beaufort scale 7 and 10 (wind velocity 30kts and 50kts respectively) and significant wave height is put as 5.2m and 11.2m. (3) The formula recommended by International Towing Tank Conference (ITTC) is used to calculated the wave spectrum. The results of this study are as follow : The results of this study are as follow : (1) Most of the vessels with beam of 20 meters or less was found to be capized in the waves abeam under the sea condition of Bearfort scale7(30kts). (2) For the vessels range 20m to 30m was found safe under the sea conditions of Bearfort scale 7(30kts) and imminent danger under the sea condition of Beaufort scale 11(50kts). (3) It is proved that any vessel could be capsized by heavy rolling regardless of vessel's size whenever the motion is synchronized with waves abeam. This study concludes that the navigator, especially at night , must anticipate the exact wave direction, referring to the wether report and coastaline, not to lay the vessel in the serial wave abeam.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.1
• /
• pp.9-20
• /
• 1988

Lespedeza species have been widely used not only as plant resources for bark, leaves and honey, but also as erosion control materials. This study was carried out to investigate the structural and wood tiber characteristics in order to obtain basic information for the utilization of the wood. The wood structure was investigated for 10 selected species and the wood fiber, for the 5 selected species among Lespedeza species distributed all over the country. The following results were obtained. In the cross section, campylotropis showed ray diffuse porous wood, L. bicolor, L. cyrtobotrya, L. thunbergii var. intermedia, diffuse porous wood, and L. tomentella, L. angustifolioides. L. maritima, L. robusta, L. patentibicolor, ring porous wood. The maximum diameter of a single vessel ranged 66-123 ${\mu}$ in all species. Campylotropis showed the most number of vessels, L. angustifolioides, the least. The number of ray per mm ranged 7-22, Campylotropis showed the most number of rays, L. angustifolioides, the least. In the radial section the average length of vessel ranged 121-250 ${\mu}$ in all species. L. thunbergii var. intermedia showed the longest vessel, L. tomentella, the shortest. In tangential section the average width of the uniseriate ray ranged 9.2-14.7${\mu}$, that of the multiseriate ray, 19.2-42.1 ${\mu}$. The average height of the uniseriate ray ranged 143.0-1162.0 ${\mu}$. The width of fiber ranged 10.12-13.61 ${\mu}$, L. maximowiezii showed the narrowest tiber, L. thunbergii var. intermedia. the widest, the thickness of fiber wall ranged 2.93-3.71 ${\mu}$ in the five species. L. maximowiezii showed the most thin fiber wall, L. thunbergii var. intermedia, the thickest, L. cyrtobotrya showed the difference in the size of fiber between the shade and the sunny sites but L. maximowiezii showed no difference. There was significant difference in fiber length, fiber width and wall thickness between L. eyrtobotrya and L. maximowiezii.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.476-486
• /
• 2010

Fishing efficiency of a trawl vessel can be enhanced by increasing the swept area per unit time, which can be attained either by increasing the mouth size of the net, or by increasing the towing speed. To improve fishing and fuel efficiency of trawl vessels targeting fishes of greater mobility, in which the towing speed is more critical in determining fishing efficiency, we conducted a series of model tests to evaluate the performance of the newly-designed nozzle propeller before installing it in a trawl vessel to verify its towing speed and fuel efficiency in the sea. By conducting further model tests in the experimental basin, we redesigned the propeller of stern trawler to improve the resistance and propulsion performance. Through actual fishing operations, we evaluated the improvement in fuel and fishing efficiency by installing the new nozzle propeller. The trawling speed increased by 0.6kts at the same engine power (RPM), while the engine margin increased by more than 20%. The increased towing speed by installing the redesigned propeller is expected to enhance fishing performance through increasing the number of hauling- and casting operations per unit times, while shortening the towing duration. Analysis of the Catch-Per-Unit-Effort (CPUE) data indicated that the mean CPUE of trawl fishery increased from 3.04kg/m in year 2007 to 6.15kg/m in year 2008, confirming enhanced fishing efficiency by adopting the redesigned propeller.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.478-483
• /
• 2012

The speed performances of ice sea trial on the Arctic(2010 & 2011) area were shown different results depend on the ice floe size. Penetration phenomena of level ice was not happened on medium ice floe and tore up by the impact force because the mass of medium ice floe is similar to the mass of Araon which is Korean ice breaking research vessel and did not shut up by the ice ridge or iceberg. The sea trial on the Amundsen sea was performed at the big floe which is classified by WMO(World Meteorological Organization). Three measurements of ice properties and five results of speed trial were obtained with different ice thicknesses and engine powers. To evaluate speed of level ice trial and model test results at the same ice thickness and engine power, the correction method of HSVA(Hamburg Ship Model Basin) was used. The thickness, snow effect, flexural strength and friction coefficient were corrected to compare the speed of sea trial. The analyzed speed at 1.03m thickness of big floe was 5.85 knots at 10MW power and it's 6.10 knots at 1.0m ice thickness and the same power. It's bigger than the results of level ice because big floe was also slightly tore up by the impact force of vessel based on the observation of recorded video.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.2
• /
• pp.97-104
• /
• 2009

Ever increasing fuel prices, almost doubled in the last three years, and global pressure to reduce their environmental impact have been enforcing commercial vessel operators and designers to re-assess current vessel designs with emphasis on their propulsion systems and operational practices. In this paper the "Inclined Keel Hull (IKH)" concept, which facilitates to use larger propeller diameter in combination with lower shaft speed rates and hence better transport efficiency, is explored for a modern 3600 TEU container vessel with the aim of fitting an 13 % larger diameter propeller (and hence resulting 20% lower rpm) to gain further power saving over the similar size basis container ship with conventional "level keel" configuration. It appears that successful application of the "inclined keel Hull" concept is a fine balance amongst the maximum gain in propulsive efficiency, minimum increase in hull resistance and satisfaction of other naval architectural and operational requirements. In order to make the concept economically more viable, this paper concentrates on the fore body design with the possible combination of increase of volume in its fore body to recover the expected volume loss in the aft body due to the space for larger propeller and its low wave-making resistance to minimize the efficiency loss using a well-established optimization software.

• Journal of Navigation and Port Research
• /
• v.26 no.2
• /
• pp.221-226
• /
• 2002

To provide reliable data for drift prediction models, field experiments were carried out in the coastal region off Busan port. Four different size of vessels(10, 30, 50, 90G/T ton) were deployed for the experiment. Among them G/T 50ton class vessel was equipped with instruments measuring the currents, winds, headings and trajectory data. In the rest of vessels only the position data were recorded for the purpose of target divergence study. The trajectories of each vessel were measured by DGPS(Differential Global Positioning System) and collected by APRS(Automatic Position Reporting System). The experiment was done in wind of 2~10m/s and current of 0.5~1.5m/s. The leeway was derived by subtracting surface current velocity from target drifting velocity. The leeway rate of G/T 50ton vessel was found to be about 3.6% and the computed leeway speed equation was $U_L$=0.042 W - 0.034. The processed leeway angle data were deflected by $-30^{\circ}$~$40^{\circ}$ from the direction of ship drift.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2011

The accurate results of finite element analysis are directly related to reliability FE model which is exactly describing dynamic characteristics of target structure. So, a model updating is necessary to establish reliable FE(Finite Element) model with a lot of experience and effort using modal testing. A large structure is too difficult to obtain the dynamic characteristics owing to its weight and size. In this work, using main gun firing test, modal testing was performed to obtain dynamic characteristics of large naval vessel, which is difficult to tap the general modal testing method. The result of experiment was considered its possibility and future plans.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.362-373
• /
• 2016

The on-line measurement of high-power IGBT collector current is important for the hierarchical control and short-circuit and overcurrent protection of its driver and the sensorless control of the converter. The conventional on-line measurement methods for IGBT collector current are not suitable for engineering measurement due to their large-size, high-cost, low-efficiency sensors, current transformers or dividers, etc. Based on the gate driver, this paper has proposed a current measuring circuit for IGBT collector current. The circuit is used to conduct non-intervention on-line measurement of IGBT collector current by detecting the voltage drop of the IGBT power emitter and the auxiliary emitter terminals. A theoretical analysis verifies the feasibility of this circuit. The circuit adopts an operational amplifier for impedance isolation to prevent the measuring circuit from affecting the dynamic performance of the IGBT. Due to using the scheme for integration first and amplification afterwards, the difficult problem of achieving high accuracy in the transient-state and on-state measurement of the voltage between the terminals of IGBT power emitter and the auxiliary emitter (u_Ee) has been solved. This is impossible for a conventional detector. On this basis, the adoption of a two-stage operational amplifier can better meet the requirements of high bandwidth measurement under the conditions of a small signal with a large gain. Finally, various experiments have been carried out under the conditions of several typical loads (resistance-inductance load, resistance load and inductance load), different IGBT junction temperatures, soft short-circuits and hard short-circuits for the on-line measurement of IGBT collector current. This is aided by the capacitor voltage which is the integration result of the voltage uEe. The results show that the proposed method of measuring IGBT collector current is feasible and effective.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.8
• /
• pp.2051-2056
• /
• 2014

This paper investigated the separation of magnetic signal from a ferro-magnetic object. The magnetic signals were ILM(induced longitudinal magnetization) and IVM(induced vertical magnetization), which were induced by earth magnetic field and PLM(permanent longitudinal magnetization) and PVM(permanent vertical magnetization), which were due to a permanent magnetization of the object, respectively. Magnetic signal separation was based on the fact that magnetization vector could be analyzed according to longitudinal and vertical directions. Also the influence of non-uniform magnetic field from a rectangular coil on the separation was examined. A military vessel with a size close to rectangular coil has more errors on the magnetic signal separation.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.99-105
• /
• 2019

Unlike typical a dynamic positioning (DP) system, a DP-assisted mooring system must determine a set point (SP) that can ensure a mooring tension safety range to prevent an excessive increase in mooring tension. In this paper, a new algorithm for determining the SP is suggested in order to reduce the tension on all the mooring lines. To determine the SP, a working area around the vessel is represented by a rectangular grid. Thus, the size of the grid area is limited considering the offset of a vessel with a mooring system. At each grid's nodes, the resultant tension from all the mooring lines is estimated using the time history of the tension and vessel's position. The results of static analyses for each grid position are used to estimate the global tension. Consequently, the SP is automatically selected as a position satisfying criterion for minimizing the total tension. In order to validate the suggested algorithm, a motion simulation with the control system in the time domain and a discussion of the results are presented.