• Journal of Chest Surgery
• /
• 제28권7호
• /
• pp.671-677
• /
• 1995

Skeletonization of the internal mammary artery [IMA during myocardial revascularization procedures may provide some advantages, compared with the pedicle graft of the artery. In 17 patients undergoing IMA grafting by skeletonization technique, flow through the artery was measured on mean arterial pressure of 50-55 mmHg immediately after cardiopulmonary bypass started [first flow and just before its anastomosis to left anterior descending artery [second flow . In 16 patients except 1 patient whose graft was injured during mobilization, the first flow of IMA graft was 32.3 $\pm$ 7.4 ml/min and the second flow increased to 59.6$\pm$25.9 ml/min without any treatment and the site for anastomosis of the IMA graft was more than 1.0 cm above the bifurcation. On the basis of previous clinical studies, the flow of the skeletonized IMA was greater than that of the pedicle graft [59.6 $\pm$ 25.9 ml/min versus 37.7$\pm$ 14.1 ml/min, p < 0.05 . In comparison between the skeletonized IMA and the IMA graft intraluminally dilated with papaverine solution, there was no significant difference between two flows[59.6 $\pm$25.7 ml/min versus 74.7 $\pm$31.4 ml/min, not significant , but the former showed longer graft and anastomosis of more proximal portion of the graft to left anterior descending artery. In conclusion, the technique of internal mammary artery skeletonization has consistently produced a satifactory conduit for myocardial revascularization procedures. We have adopted IMA skeletonization not only because of the flow, diameter, and vessel length obtained but also because of limited perivascular tissue disruption that occurs during the dissection.

• 대한기계학회논문집A
• /
• 제36권9호
• /
• pp.1047-1052
• /
• 2012

가압경수로형 원전의 Alloy 600 원자로압력용기헤드 관통노즐 및 Alloy 82/182 이종금속 맞대기 용접부에서 일차수응력부식균열(PWSCC)이 보고된 이후 전 세계적으로 PWSCC에 의한 용접부 파단을 예방하기 위해 강화검사를 적용하고 있다. 본 이종금속용접부에 대한 가동중검사에서 균열이 발견된 경우 건전성평가 결과가 도출되기까지 발전소가 정지 상태에 있게 됨에 따라 원전 이용율 저하가 발생할 수 있는데, 이를 예방하기 위해서는 균열건전성평가 관련 기술의 정립뿐만 아니라 신속하게 평가 결과를 도출할 수 있는 시스템의 구축이 필요하다. 본 연구에서는 이종금속 맞대기 용접부를 대상으로 진행하고 있는 PWSCC 균열건전성평가 기준 정립 및 전산 시스템 개발 결과를 제시하였다. 본 연구를 통해 이종금속 맞대기 용접부 PWSCC 균열건전성평가 기술이 정립되고 전산 시스템으로 구현되어 원자로압력용기 주변 이종금속 맞대기 용접부에서의 PWSCC 균열에 대한 기술적 건전성평가 수단을 확보하였다.

• 비파괴검사학회지
• /
• 제18권6호
• /
• pp.477-483
• /
• 1998

원자로 압력용기 재료인 SA508 steel을 온도 $70^{\circ}C$와 대기압하에서 최고 $10^{18}n/cm^2$까지 중성자를 조사시켜 조사량에 따른 자기이력곡선과 Barkhausen noise amplitude(BNA), Barkhausen noise energy(BNE) 및 미세경도 변화를 측정하여 이들 사이의 상관관계를 구하였다. 중성자 조사에 의하여 자기이력곡선은 변화가 없었으며, BNA, BNE 및 경도는 중성자 조사량에 따라 세 단계의 변화를 보였으며, 중성자 조사량이 $10^{17}n/cm^2$에서는 급격히 변하여 이들 사이의 상관관계가 있음을 알 수 있었다. 따라서 BNA와 BNE가 중성자 조사에 의한 재료의 미세 구조 결함을 조사하는데 비파괴적인 방법으로 가능성이 있음을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제48권1호
• /
• pp.41-49
• /
• 2020

Jabon (Anthocephalus cadamba) is a fast-growing wood species that is widely utilized for light construction and other purposes in Indonesia. The objectives of the current study were to determine the effects of monoethylene glycol (MEG) and SiO₂ nanoparticles (nano SiO₂) impregnation treatment on the dimensional stability and density of jabon wood and to identify the characteristics of impregnated jabon wood. Wood samples were immersed in water (as untreated), MEG, 0.5% MEGSiO₂, then impregnated by applying 0.5 bar of vacuum for 60 min, and then applying 2.5 bar of pressure for 120 min. The results showed that impregnation with MEG and Nano SiO₂ had a significant effect on the dimensional stability of jabon wood. Polymers can fill cell walls in wood indicated by increasing weight percentgain, antiswelling efficiency, bulking effect, and density, then decreasing in water uptake value. Jabon wood morphology by using SEM showed that MEGSiO₂ polymers can cover part of the pitsin the wood vessel wall of jabon. This finding was reinforced by EDX results showing that the silicon content was increased due to the addition of SiO₂ nano. The XRD diffraction pattern indicated that MEGSiO₂ treatment increased the degree of crystallinity in wood samples. Overall, treatment with 0.5% MEGSiO₂ led to the most improvement in the dimensional stability of 5-year-old jabon wood in this study.

• Nuclear Engineering and Technology
• /
• 제26권4호
• /
• pp.493-501
• /
• 1994

하향 가열 평판에서의 풀비등 임계열유속 실험이 수행되었다. 이는 원자로에서의 노심용융사고 발생시 그 결과를 완화시키는 한 방법으로 고려되고 있는 원자로용기 외부 냉각 (Ex-Vessel Flooding) 개념과 연관된다. 대기압하, 포화상태 물에서 너비가 다른 두 개의 평판 (20mm$\times$200mm및 25mm$\times$200mm)을 이용, -90$^{\circ}$(평형 하향), -88$^{\circ}$, -86$^{\circ}$, -84$^{\circ}$, -60$^{\circ}$와 -40$^{\circ}$의 경사 가도에 대한 임계열유속이 측정되었다. 실험 결과 너비가 큰 평판에서, 그리고 수직 위치로부터의 각도가 클수록 임계열유속이 낮게 나타났다. 이는 가열면에서 발생된 기포들의 이탈이 어려워지기 때문인 것으로 판단된다. 경사가도에 따른 전체적 인 임계열유속 경향은 기존 연구들과 대체로 일치하나, 임계열유속 감소율이 변화하는 천이 각도가 -80$^{\circ}$ 근방에서 발견되었다.

• 대한토목학회논문집
• /
• 제39권3호
• /
• pp.369-380
• /
• 2019

PSC 구조물에 폭발과 같은 극한하중이 짧은 시간 동안 발생하게 되면 급작스러운 파괴와 그로 인한 수많은 인명 및 재산피해를 발생시킨다. 하지만 원전격납구조물, 가스탱크와 같은 PSC 구조물의 경우 방호 및 방재개념이 포함된 구조설계가 적용되지 않은 실정이며, 특히, 구조물 내부에서 발생하는 폭발압력하중은 피해규모가 외부폭발에 비해 훨씬 크기 때문에 내부폭발하중에 대한 검증은 반드시 필요하다. 따라서, 본 연구에서는 원전격납구조물의 내부폭발에 대한 저항성능을 검토하기 위해 이방향 프리스트레스트 콘크리트 축소모형을 제작하였다. 내부폭발 실험은 22.68, 27.22, 31.75 kg (50, 60, 70 lbs)의 ANFO 폭약을 이용하여 시편으로부터 1,000 mm의 거리에서 폭발시켰으며, 압력하중, 처짐, 변형률, 균열형상, 긴장력 변화 등의 데이터를 분석하였다. 본 연구결과를 이용하여 원전격납구조물의 내부폭발하중 발생 시 손상도 범위 예측이 가능할 것으로 판단된다.

• 한국기계가공학회지
• /
• 제19권11호
• /
• pp.1-7
• /
• 2020

Recently, hydrogen has gained considerable attention as an eco-friendly fuel, which helps in reducing carbon dioxide content. Specifically, there is a growing interest in vehicles powered by a hydrogen fuel cell, which is spotlighted as an environmental-friendly alternative. A hydrogen transport system, fuel cell system, fuel supply system, power management system, and hydrogen storage system are key parts of a hydrogen fuel cell truck. In this study, a hydrogen storage system is built and analyzed. The expansion length of the storage vessel at maximum operating pressure (87.5 MPa) was calculated with ABAQUS, and then the optimized system was designed and built. The leak and bubble tests were performed on the built storage system. The leakage of the system was measured to be under 5 cc/hr. Hence, it can be used as a research test for the safety evaluation of leading systems of hydrogen fuel-powered commercial vehicles.

• 대한금속재료학회지
• /
• 제47권3호
• /
• pp.139-146
• /
• 2009

The heat-affected zone (HAZ) of SA508 Gr.4N Ni-Mo-Cr low alloy steel, which has higher Ni and Cr contents than SA508 Gr.3 Mn-Mo-Ni low alloy steel, was investigated on the microstructure and mechanical properties. The HAZ was categorized into seven characteristic zones (CGCG, FGCG, ICCG, SCCG, FGFG, ICIC and SCSC-HAZ) according to the peak temperature from the thermal cycle experienced during multi-pass welding. Post Weld Heat Treatment (PWHT) was conducted in the temperature range of $550{\sim}610^{\circ}C$ for 30 hours to evaluate the effect of PWHT conditions on the microstructure and mechanical properties. Before PWHT, CGHAZ and FGFGHAZ showed high yield strength (YS) ranging from 1000 to 1250 MPa, while YS of SCSCHAZ decreased from 607 MPa (observed for base metal) to 501 MPa. The Charpy impact energies of sub-HAZs fell below 100J at $-29^{\circ}C$, except in the SCSCHAZ. By applying PWHT to sub-HAZ specimens, YS decreased as the PWHT temperature increased. In the case of CGHAZs and FGFGHAZ heat-treated at $610^{\circ}C$, YS dropped drastically to the range of 654~686 MPa. From the Charpy impact test, the upper-shelf energy (USE) increased to approximately 250J and Index temperature ($T_{68J}$) decreased below $-50^{\circ}C$. Specifically, in FGFG, ICIC and SCSC-HAZ, $T_{68J}$ was below -110, which was lower than the case of base metal.

• 한국가스학회지
• /
• 제25권1호
• /
• pp.40-47
• /
• 2021

본 연구에서는 화재폭발 사고의 원인 규명을 위하여 다양한 시험 장비를 사용하여 유기과산화물의 일종인 터셔리부틸퍼옥시말레이트(TBPM)의 분해 및 폭발 위험성을 조사하였다. 시차주사열량(DSC) 분석결과, TBPM의 순간동력밀도(IPD)는 26,401 kW/ml로서 NFPA 반응성지수(Nr)가 4로 분류되었다. 또한 발열량과 개시온도 측정값을 이용한 폭발전달성(EP)과 충격감도(SS)는 양의 값을 나타내며 위험성이 있는 것으로 예측되었으며, 평가 장비를 활용한 실험적 결과로부터 충격감도와 마찰감도는 각각 4급 및 5급으로 평가되었다. 압력용기시험에서는 USA-PVT No.가 4로 분류되어 자기반응성물질에 해당되는 것으로 나타났다. 연소속도에 대한 조사 결과로부터 TBPM은 167 mm/sec의 연소속도를 나타내며 인화성고체 분류2에 포함되는 것으로 평가되었다.

• Nuclear Engineering and Technology
• /
• 제55권5호
• /
• pp.1651-1664
• /
• 2023

It is very difficult to capture the multi-dimensional phenomena such as asymmetric flow and temperature distributions with the one-dimensional (1D) model, obviously, due to its inherent limitation. In order to overcome such a limitation of the 1D representation, many state-of-the-art system codes have equipped a three-dimensional (3D) component for multi-dimensional analysis capability. In this study, a standard multi-dimensional analysis model of APR1400 (Advanced Power Reactor 1400) has been developed using TRACE (TRAC/RELAP Advanced Computational Engine). The entire reactor pressure vessel (RPV) of APR1400 has been modeled using a single 3D component. The fuels in the reactor core have been described with detailed and coarse representations, respectively, to figure out the impact of the fuel description. Using both 3D RPV models, a comparative analysis has been performed postulating a double-ended guillotine break at a cold leg. Based on the results of comparative analysis, it is revealed that both models show no significant difference in general plant behavior and the model with coarse fuel model could be used for faster transient analysis without reactor kinetics coupling. The analysis indicates that the asymmetric temperature and flow distributions are captured during the transient, and such nonuniform distributions contribute to asymmetric quenching behaviors during blowdown and reflood phases. Such asymmetries are directly connected to the figure of merits in the LBLOCA analysis. Therefore, it is recommended to employ a multi-dimensional RPV model with a detailed fuel description for a realistic safety analysis with the consideration of the spatial configuration of the reactor core.