• 대한토목학회논문집
• /
• 제32권5A호
• /
• pp.307-315
• /
• 2012

최근 국내에서도 압축강도 180 MPa, 인장강도 10 MPa 이상의 초고성능 섬유보강 콘크리트(Ultra High Performance Fiber Reinforced Concrete, UHPFRC)가 개발되었다. 그러나 UHPFRC는 물-결합재비가 낮고 다량의 고분말 혼화재료를 혼입하며, 굵은 골재를 사용하지 않기 때문에 초기 재령에서의 자기수축이 크고, 표면이 급격히 건조하는 등 기존의 일반 콘크리트(Normal Concrete, NC) 및 고성능 콘크리트(High Performance Concrete, HPC)와는 다른 재료적 특성을 보인다. 그러므로 본 연구에서는 UHPFRC에 적합한 재료 실험 방법과 규정을 제안하고 극 초기 재령에서의 강도 특성을 평가하기 위하여 응결 및 수축, 인장 실험을 수행하였다. 응결 실험 결과 파라핀 오일을 UHPFRC의 모르타르 표면에 적용할 경우 표면에서의 급격한 건조현상을 효율적으로 억제할 수 있는 것으로 나타났으며, 시멘트와 배합수의 수화반응을 지연 또는 촉진 시키지 않는 것으로 나타나 응결 실험 시 표면건조 방지제로 적합한 것으로 판단되었다. 또한, 링-테스트를 수행하여 내부 강재 링의 온도와 변형률의 경향이 달라지는 시점을 수축 응력 발현 시점으로 정의하였으며, 이를 응결 실험과 비교하여 본 결과 응결침에 걸리는 관입 저항력이 약 1.5 MPa일 때 수축 응력이 발현되는 것으로 나타났다. 이는 초결 및 종결보다 약 0.6시간, 2.1시간 빠른 것이며, 상기 시점을 UHPFRC의 자기수축 측정 시점(time-zero)으로 규정하였다. 마지막으로, 본 연구에서는 극 초기 재령 인장강도 측정 장비를 제작하여 초결시점에서부터 UHPFRC의 인장강도와 탄성계수를 측정하였으며, 이를 고려한 UHPFRC의 인장강도 및 탄성계수 예측식을 제안하였다.

• 콘크리트학회논문집
• /
• 제25권1호
• /
• pp.73-80
• /
• 2013

이 연구는 폴리머 시멘트 슬러리로 도장한 도장철근의 부착강도 개선에 영향을 미치는 초기재령에서의 PCS 도장재 배합에 관한 연구로 폴리머의 종류, 시멘트의 종류, 폴리머 시멘트비, 도장재의 양생재령, 도장두께 등을 변화시켜 배합을 설정하여 부착강도 시험을 실시하였다. 이 연구 결과, PCS 도장철근의 부착강도는 거의 모든 배합에서 도장하지 않은 보통철근 및 에폭시철근에 비해 높은 부착강도를 나타냈다. 도장철근의 최대 부착강도는 보통철근에 비해 1.52배, 에폭시 철근에 비해 1.58배로 높게 나타났으며, 도장두께는 $100{\mu}m$에서 우수하였으며, 시멘트는 초조강 시멘트, 폴리머는 EVA, 폴리머 시멘트비는 80%~100% 범위에서 우수한 부착강도를 나타냈다. 또한 양생재령에 있어서는 3시간의 단시간 양생에 의한 부착강도도 양생재령 1일 및 7일에 비해 열악하지 않고 동등이상의 부착강도를 나타내 실제 현장에서의 사용성면에서 유리한 것으로 볼 수 있다.

• 한국건축시공학회지
• /
• 제3권4호
• /
• pp.87-94
• /
• 2003

This study is to investigate the temperature hysteresis and development of compressive strength due to the curing conditions and to evaluate the optimum curing condition of test specimens showing the same development of strength to that of real structures in cold weather. The results of temperature curve with curing conditions in mock-up tests showed the trend of decrease plain concrete with insulation form, plain concrete with heating, concrete with accelerator for freeze protection, and control concrete in turn. The strength development of plain concrete of inside and outside of shelter showed the very slow strength gains due to early freezing, but that of concrete with accelerator for freeze protection showed the gradual increase of strength with time. From this, it is clear that accelerator for freeze protection has the effects of refusing the freezing temperature and accelerating the hardening under low temperature. Strength test results of small specimens embedded in members and located in insulation boxes at the site are similar to that of cores drilled from the members at the same ages, thus it is clear that these curing methods are effective for evaluating in-place concrete strength

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.1071-1076
• /
• 2003

Basic creep of concrete during very early ages is an important factor on the behavior of young concrete and a great deal of research has been executed. However, in recent studies, it was revealed that the basic creep measured by sealed concrete was inaccurate, especially for high strength concrete because of autogenous shrinkage at early age. This paper presents the results from experimental study that investigate to explore the effect of autogenous shrinkage in basic creep. More specifically, four different mix proportions were casted and the primary variables were water-cement ratios. Through this research, it was found that the differences between apparent specific creep and real specific creep were remarkable in low water-cement ratio at early age. Therefore, it is recommended to modify existing creep model by considering autogenous shrinkage

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.575-580
• /
• 2012

Geopolymers were synthesized using raw materials produced from two different areas: one was from Indonesia and the other was from Habcheon, Korea. The constituting phases of the Indonesian raw material were quartz and kaolinite, while those of the Habcheon sample were quartz, halloysite and albite. They were both calcined at $750^{\circ}C$ for 6 hours, and solution of NaOH and water glass was added to activate the geopolymeric reaction. The compressive strength of geopolymer synthesized from the Indonesian raw material showed a low value of $151\;kgf/cm^2$ after curing for 28 days. However, it could be greatly increased by adding blast furnace slag powders of $1188\;kgf/cm^2$ and $1969\;kgf/cm^2$ at 20 wt% and 40 wt% additions, respectively. The compressive strength of the geopolymer synthesized from the Habcheon raw material was high, at $557\;kgf/cm^2$, after 28 days, and the very high early-stage (3 days) strength of $556\;kgf/cm^2$ for this sample was remarkable. Commercially available Habcheon metastate raw material, of which composition showed low CaO and $Na_2O$ contents compared to the calcined Habcheon raw material, was also examined. It was found that the compressive strength of the commercial metastate type was nearly identical to that of the calcined Habcheon raw material except for the relatively low value at an early curing stage and at a high curing temperature of $60^{\circ}C$.

• International Journal of Reliability and Applications
• /
• 제13권2호
• /
• pp.71-80
• /
• 2012

This paper introduces a new approach for evaluating reliability of a complex system in terms of distributional parameters where analytical determination of reliability is intractable. The concept of discrete approximation, reported in the literature so far, fails to meet the latter requirement in terms of distributional parameters. The current work aims at offering a bound based approach where reliability planners not only get a clear idea about the extent of error but also can manipulate in terms of distributional parameters. This reliability approximation has been under taken under the Weibull frame work which is the most widely used model for reliability analysis. Numerical study has been carried out to examine the strength of our proposed reliability approximation via closeness between the two reliability bounds. This approach will be very useful during the early stages of product design as the distributional parameters can be adjusted.

• 한국재료학회지
• /
• 제21권9호
• /
• pp.502-508
• /
• 2011

The goal of the present work was to investigate the development of a geopolymeric ceramic material from a mixture of mine residue, coal fly ash, blast furnace slag, and alkali activator solution by the geopolymer technique. The results showed that the higher compressive strength of geopolymeric ceramic material increased with an increase in active filler (blast furnace slag + coal fly ash) contents and with a reduction of mine residue contents. The geopolymeric ceramic had very high early age strength. The compressive strength of the geopolymeric ceramic depended on the added active filler content. The maximum compressive strength of the geopolymeric ceramic containing 20 wt.% mine residue was 141.2 MPa. The compressive strength of geopolymeric ceramic manufactured by adding mine residue was higher than that of portland cement mortar, which is 60 MPa, when cured for 28 days. SEM observation showed the possibility of having amorphous aluminosilicate gel within geopolymeric ceramic. XRD patterns indicate that the geopolymeric ceramic was composed of amorphous aluminosilicate, calcite, quartz, and muscovite. The Korea Standard Leaching Test (KSLT) was used to determine the leaching potential of the geopolymeric ceramic. The amounts of heavy metals were noticeably reduced after the solidification of mine residue with active filler.

• 열처리공학회지
• /
• 제24권1호
• /
• pp.37-44
• /
• 2011

High temperature wear of AlCrN coated tool steels sliding against the ultra-high strength boron steels used for hot press forming has been studied. The sliding wear tests have been carried out using a pin-on-disc of configuration under applied normal load of 50 N for 20 min with heating the ultra-high strength boron steels up to $800^{\circ}C$. Characterizations of tribolayers formed on the contacting surfaces between the tribopairs of the AlCrN coated tool steels and the ultra-high strength boron steels have been studied. It was found on the tribolayers of the AlCrN coated tool steels that microcracking and oxides containing Fe and Cr to increase friction coefficient were formed at the early stage of sliding wear, followed by the generation of the smeared oxide layers containing Fe transferred from the tribopair to decrease friction coefficient. This may mainly contribute to very low specific wear rate of the AlCrN coated tool steels sliding against the ultra-high strength boron steels, resulting from oxideoxide contact between the tribopair.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.341-344
• /
• 1999

In the case of the offshore concrete structures like the anchorage block of a suspension bridge of Kwangan Grand Road, there is a need of the concrete which has low heat of hydration and good resistance for sea-water attack. In this study, the blended super low heat cement which satisfies that requirement was developed and several tests were carried out. The concrete using the blended super low heat cement showed lower adiabatic temperature rise than 3$0^{\circ}C$ and good early strength. Also, its passed charge(coulomb) to resist chloride ion penetration was very low.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.241-242
• /
• 2010

본 연구는 건식 스프레이 모르타르를 적용한, 보수 보강용 모르타르 재료 개발을 위한 기초 물성 실험을 실시하는데 그 목적을 두었다.