• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.18 no.2
• /
• pp.101-108
• /
• 1982

In this paper the result of heat transfer analysis around the square heat source of interior solid by using the F. E. M is reported. Calculation for temperature distribution and each element was used by F. E. M. the solid is sub-divided into system of equal size triangular shape. These values of temperature distribution will valuable for design of jet engine and steam generator and the results gained are as follow; 1. Calculation by F. E. M is identified with the experiment. 2. Temperature distribution on the horizontal surface is $\theta$=0.698 in model 4 and the other hand $\theta$=0.401 in model 6 for X=16cm. In intermediates surface between heat source and bottom surface, the influence of L is more greater than that of height in the temperature difference. 3. Temperature distribution on the vertical surface for model 2 is resulted strong influence by K. In the case of Y=4cm is identified with $\theta$=0.0790 for K=7 and also $\theta$=0.0036 for K=0.3. In the difference of temperature distribution.

• The korean journal of orthodontics
• /
• v.19 no.1 s.27
• /
• pp.201-218
• /
• 1989

This study was focused on the distribution of different facial types of the Class II division I malocclusion groups and skeletal characteristics of the each group and those that anteropsterior relationship of the maxilla and mandible calculated from the analysis of ANB angle and Wits appraisal was quite different from each other, as well. Cephalometric headplates of 140 persons of Class II division 1 malocclusion whose mean age was 11.2 years and 69 persons of normal occlusion whose mean age was 12.2 years were utilize as materials. Measurements were recorded, tabulated and statistically analyzed employing the tracings of the lateral cephalograms, then Class II division 1 malocclusion group was divided into 9 Types according to the angle of SNA and SNB for the anteroposterior relationship of the maxilla and mandible, another 9 Types according to the FH-NPog and SN-MP for the horisontal and vertical relationship, and the other 9 Types according to the ANB and Wits appraisal for intermaxillary relationship as well, with which was based on $Mean{\pm}$ 1SD of those of normal occlusion. The result allowed the following conclusion: 1. $37.1\%$ of population demonstrated maxilla within nounal range and retrognathic mandible to the cranial base, $30\%$ for both maxilla and mandible within normal range, $20\%$ for retrognathic maxilla and mandible and $12.9\%$ of the rest were ananged in Class II division 1 maloccusion groups. 2. Retrognathic mandible and hyperdivergent face accounted for $30.7\%$, mesognathic mandible and neutrodivergent face for $29.3\%$, mesognathic mandible and hyperdivergent face for $16.4\%$, retrognathic mandible and neutrodivergent face for $13.6\%$, mesognathic mandible and hypodivergent face for $10\%$ of population were computed in Class II division 1 malocclusion groups. 3. It was suggested that skeletal Class II malocclusion might be due to anomaly in size and shape of cranial base, underdevelopment of mandible, retropositioning of mandible, underdevelopment of posterior face against anterior face, or any combination of these factors. 4. Population with underdevelopment and / or retropositioning of the mandible showed hyperdivergent tendency of facia profile. 5. The ANB angle and Wits appraisal did not coincide the severity of anteroposterior dysplasia in $35.7\%$ of Class II division 1 malocclusion group each other, and this inconsistency was suggested to be related with mandibular rotation, inclination of cranial base, and anteroposterior position of the maxilla.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2008.11a
• /
• pp.587-590
• /
• 2008

Typically, General contractor in the construction industry can not plan their own of the amount of orders received, and because of the size of wide fluctuations in the amount of annual orders received for equipment or personnel to full-time employment has limits. Therefore, with a vertical division of labor between specialist trades which distributed the risk and the intention to improve the efficiency of production will be. For this reason, the production structure of the general subcontracting relationships are formed. In this way, Depending on the structure of production outsourced management of the project is the impact on the successful completion. Nevertheless, most construction companies do not achieve effective an organized cooperation until now. This study is to understand the actual conditions an organized cooperation between general contractor and specialist trades, and is look at ways to improve with find the complement. This paper is a preliminary study of the leading research based on the present condition of the cooperating companies considered to be the cause. A result of Analysis, the actual conditions in cooperation of the construction industry is staying in an external form of organizational cooperation And were not effective utilization of the organization for the cooperation a production. Specialist trades have had to register as partners for the amount of orders received, the level of practical cooperation was almost no activity to improve a production. in each step an organized cooperation in the construction industry, to improve productivity construction and to create of economic value for the cooperation of production is required.

• Journal of the Korean Society of Costume
• /
• v.17
• /
• pp.221-245
• /
• 1991

The purpose of the study is to search for the existene mode of the modern cosmetology by not only understanding generally but also looking into the fundamental mental base and the aesthetic senses reflected in the literatuers and remans concerned with the traditional Korean cosmetology from anient times to modern times (1910). What are characteritic of in the systemetic study are summarized as follows : Chapter I The purposes and methods are systematized and the scop of study is specified. Chapter II The definition of cosmetology and osmetic indicates that the traditional cosmetology is a sort of whole deoration with costume. Chapter III It can hypothesized that since the Koreans were the northern nomadic tribe, in the beginning the cosmetology might have had a practical usage to protect themselves from the cold weather, and then gradually become to have a decoration meaning, and finally, with the development of various social culture, undergone the transition reflecting some characteristic of each era. Chapter IV While the female cosmetology had been much likely to accomodate the spirit of the times under the male, most of the male cosmetology had been done as a means to exhibit his social position, the tendency which had been prominent in the Yi dynasty. Chapter V Sinece beauty kits which were made of raw materials had been selg-supplying only to meet the small demand, their size were relatively small and had been given a menaing of a luchy omen or exorcism. Chapter VI Buddhism introduced bathing and incense, Confucianistic view of womanhood differentiated the cosmetology between Kissang and daughters of respectable citizens, and thin make-up was recomended. In addition, there many thoughts to have influence on the traditional cosmetology culture : body-and-soul unity, exorcism, naturalism, and short-lived beauty. Chapter VII Since the on-going movement of makeing use of the traditional cosmetic materials in order to apply to modern cosmetic may be a king of counter-vertical cultural phenomena to incorporate our own tradition with the modern cosmetology culture efficiently, the hope is that the findings of the study may contribute to the said efforts. In short, the study on the traditional cosmetology culture may be heloful in Looking into the existence of the modern cosmetology through its clarification of the nature of the traditional cosmetology culture.

• Journal of Fashion Business
• /
• v.14 no.1
• /
• pp.57-75
• /
• 2010

This study is done in Shanghai area by sample survey of female college students in their lower 20s. Through direct contact survey, this study collected and analyzed information on figure to understand feature of breasts and measurements of body to provide base information to improve product of brassiere for adult female in China. Data was analyzed by using SPSSWIN 13.0 Program and SAS 9.0. 1. From a result of factor analysis on 40 items of measures to derive the components of the shape of the breast, 6 factors were derived such as the factors to show the obesity of the bust, to show the ratio of the upper and lower area of the lower bust, droop and volume, to show the internal shape and broadness of the bust, to show the location and vertical size of the bust, to show the protrusion of the bust and the eternal shape of the bust. 2. From a result of classification on the shape of the breast of the Chinese women in their early 20s, 4 types were selected. Type 1 is the protrusion type that a woman has a broad drooped breast due to the development in the upper and lower parts of the chest as well as the highest height, a high degree of obesity in the bust part, big volume and much protrusion. Type 2 is the hemisphere type that the degree of obesity in the breast is second to Type 1 and a breast is located at a region higher than Type 1 as the degree of obesity in the breast is secondly highest, the lower part of the bust is bigger than the Type 1 and the degree of being broad and drooped is second to Type 1. Type 3 is the cone type with a breast of being drooped and broad a little bit and a certain degree of a volume. Type 4 is the flat type with the smallest value in the item that shows the obesity of the bust area and with the smallest value in the R$\ddot{o}$hrer index to have the small and slender body type for the bust area, which is somewhat flat due to a low slope at the internal side of the bust.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.476-482
• /
• 2006

In this paper, a multimode feed horn antenna is suggested for a high power microwave(HPM) antenna system. The proposed HPM feed horn antenna which is connected with a mode converter is located between source and reflector antenna. A multimode feed horn antenna which has reduced -25 dB beamwidth is designed and fabricated for miniaturization of reflector antenna because -25 dB beamwidth which is determined by considering spillover of feed horn antenna decides a size of reflector in case of HPM. As a result, feed system which uses the multimode feed horn antenna has high gain about 27 dBi and return loss is less than -22 dB at 10 GHz. The measured -25 dB beamwidths of the radiation pattern at vertical, horizontal-plane equal to $20.24^{\circ},\;28.92^{\circ}$ which is less than about $10^{\circ}$ beamwidth of conventional feed system. Thus the suggested feed hem antenna is suitable to feed horn for miniaturization of HPM antenna system.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.6
• /
• pp.303-311
• /
• 1998

Ten reinforced concrete rigid frames and infilled shear wall frames were tested under both vertical and cyclic loadings. Experiments were carried out to evaluate the structural performance of such test specimens, such as the hysteretic behavior, the maximum horizontal strength, crack propagation, and ductility etc. under load reversals. All the specimens were modeledin one-third scale size. Based on the test results reported in this study, the follwing conclusions can be made. For the rigid frame type and the fully rigid babel type shear wall specimens, the hysteresis diagrams indicate that the degradations of their strength were developed slowly beyond maximum carrying capacity. It was shown that when the hoop reinforcement ratio became higher, the energy dissipation capacity became larger and the failure mode became ductile. The specimens designed by the less hoop reinforcement for the fully rigid babel type shear wall, were mainly failed due to diagonal crack in comparison with the specimens designed by the larger hoop reinforcement ratio. Maximum horizontal resisting moment capacity of speciment designed by the fully rigid babel shear wall were increased by 5.47~7.95 times in comparison with the rigid frame type.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.78-85
• /
• 2020

The scaffolding system, which is a construction workbench of the cargo containment for a membrane LNG carrier, is a large truss structure composed of various members. To shorten the installation period and process of the scaffolding system, it is effective to enlarge the mounting unit from the existing two stages to eight stages. Owing to the increase in lifting load according to the large size of the module, the stresses around the pin and hole will be increased significantly. In this study, a tensile strength test and contact stress analysis were performed to confirm the structural safety. The relatively large hole deformation was observed visually near the average load generated in the vertical pipe at the top through tensile strength tests. A contact stress calculation confirmed the stress distribution around the hole. The contact problem was dealt with in terms of the Herzian contact stress. The possibility of 8-stage loading was examined by comparing the yield strength and contact stresses of failure critical locations. As a result, the 8-stage loading method of the existing scaffolding material was inadequate, and a new loading method with proper safety is proposed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.1
• /
• pp.9-17
• /
• 2009

Discomfort Glare from the artificial light sources is an important issue in assessment of lighting quality for healthy buildings. Glare, as a factor of the characteristics of brightness, which has been defined as the sensation produced by contrast and luminance within an entire field view, unfavorably influences the occupants who performs visual tasks. It may cause annoyance and discomfort by interruption of visibility. In the whole visual field, glare can be determined by effects of the position, the luminance and the size of the light source and brightness of the surroundings. Therefore, experimental equipment is required to maintain a constant visual lighting environment. Recent studies have been developed and used the instrument for glare sensation evaluation but the instruments showed some difficulties to verify the correlation of glare indicators. The instrument have been developed with reference to former studies. It is called the Glare Tester. This is consist of 2[m]-diameter vertical dome screen painted with white flat paint, and light sources installed inside the screen. These light sources can provide various range of brightness at any inner surface of the screen. 2 Glare light sources can provide the value of luminance within the range of $0{\sim}150,000[cd/m^2]$. Moreover, 12 light sources are used for background luminance and it can perform the value of luminance within the range of $0{\sim}350[cd/m^2]$. Several experiments have been conducted using this Glare Tester to evaluate the range of the visibility, the values of BCD and the glare sensation in lower and upper visual field.

• Korean Journal of Poultry Science
• /
• v.6 no.2
• /
• pp.91-102
• /
• 1979

The basic problem of the broiler industry is that of fluctuating prices, mainly thanks to unstable supply of and inelastic demand for products as usually indicated as a peculiarity of agricultural commodities. This particularly brings the producer to a great economic risk, because he has to sell products under the condition of pure competition, whereas others from whom he has to buy deal under the condition of oligopoly or even monopoly. Therefore, producers economic position is generally placed in the worst comparing others dealing with, which results in unbalanced economic status of elements involved in broiler operation and further obstruction of industry development as a whole. A certain type of business coordination to overcome such a problem should be measured in order to improve the efficiency of entire operation and thus assure the balanced industry development. The concept of the economic integration developed in modern business system had been adapted to U.S. poultry industry which became common later around the world as a means of stabilizing producers price and whole industry as well. There are two main typos of integration; horizontal and vertical The former refers to the general grouping of similar business units, eg. a hatchery tying with other hatchery, while the latter refers to the knitting together of two or more stages of economic activities, eg. tying together among units of hatching, fled milling, production, processing and marketing. By having the industry integrated, risk and uncertainty involved in various stages of operation could be diversified. The typo of integrating contract between producers and integrators include the share of profits, flat fee payment, feed conversion payment and salary basis. In the U.S., extensive changes in production, processing, and marketing during the last few decades have changed the thicken broiler industry from one of small, widely scattered farms to one that is largo, concentrated and efficient. More than 99 percent of all broilers produced are grown under contract and by integrated firms which vary in size of operation and complexity. About 84 percent of all production is concentrated in 10 States. Some of the other factors ;hat contributed to these choses arc costs, energy use, prices, processing, marketing and demand. No integrated broiler production system has yet been applied in Korea's poultry industry, thus all stages all broiler operation run independently seeking for its own profit. Consequently, producers price fluctuate very widely around the year even more than 50 percent in a few months. This also leads to disadvantages of material supplies, processors and distributors and enforce the industry unstable. The current economic environment in Korea seems that the time for broiler integration comes and as an ideal integrator, feed millers, food processors and producers group may be considered.