• 한국안전학회지
• /
• 제12권4호
• /
• pp.209-213
• /
• 1997

Manual lifting techniques are commonly defined in terms of the postures adopted at the start of the lift. Quantitative definition is problematic, however, because the absolute joint angles adopted to lift an object are influenced by task parameters, such as the initial height of the load. The main objective of this study is to investigate the grip strength of the both hands at the initial lifting points. The survey is conducted by measuring the compression force, anthropometric data and grip strength at the lifting postures for the subjects(n=50) who is assigned to their job as usual. The experiment is peformed at the four lifting postures which involving the combination of two horizontal factors(H1 : 35 cm, H2 : 55 cm) and two vertical factors(V1 : 20~80 cm, V2 : 47~102 cm). The analysis result of lifting posture indicated that each H1-V1, H2-V1 combinations are about 60$^{\circ}$ and each H1-V2, H2-V2 combinations are about $30^{\circ}$. There are significant differences on grip strength between $60^{\circ}$ and $30^{\circ}$ stooped posture. The results of this study can be provided a method defining lifting postures at the minimum grip strength. Also, it is eliminated a hazard of the injuries which are cumulative trauma disorders(CTDs) and back pain, increased a productivity and improved a welfare of workers.

• 대한조선학회논문집
• /
• 제48권4호
• /
• pp.308-316
• /
• 2011

Although a yacht sails operate with large displacement due to very thin thickness, many studies for flow around yacht sails have not considered the sail deformation. The sail deformation not only caused a change in the center of effect(CE) on the sail but also a change in the thrust of the sail. The change of the CE and thrust affects the center of lateral resistance(CLR) and side forces of the hull, and the balance of the yacht. These changes affect the motion of the yacht which changes the velocity of the yacht. Thus, when analyzing the flow around yacht sails, the sail deformation should be considered. In the present study, fluid-structure-interaction(FSI) analysis of a two dimensional section of yacht sails was performed to consider the effects of sail deformation on the lift and drag performance. FSI and moving mesh methods were studied. Computational methods were verified using benchmark test cases such as the flow around horizontal and vertical cantilever beams. Shape deformation, pressure distribution, lift forces and separation flow were compared for both rigid and deformable sail.

• 한국기계가공학회지
• /
• 제5권4호
• /
• pp.13-20
• /
• 2006

The inherent problem of a Darrieus wind turbine is its inability to self-start. Usually, a motor is used to provide angular acceleration until lift forces are produced in the airfoil blades or up until the turbine can already sustain its speed on its own. This paper describes a method of improving the self-starting of an H-type Darrieus vertical axis wind turbine (VAWT) by incorporating a helical Savonius turbine thus utilizing a drag-lift combination. The effect of each turbine in the combination relative to each other is investigated by testing a prototype windmill consisting of three NACA 0015 airfoil blades combined with a Savonius rotor with a helix angle of 180 degrees and whose swept area equals 30% of the entire turbine.

• 한국항공운항학회지
• /
• 제26권4호
• /
• pp.122-128
• /
• 2018

A compound drone that combines a fixed wing and a rotary wing is an aircraft that can take off and landing vertically, and can increase flight time and fly faster with fixed wings. The compound drones are divided into many types depending on the method of adding the thrust vectoring or the lift fan and the position of the rotor. In this study, we designed and fabricated a composite drone with four V-TOL motors in a fixed-wing, and assigned missions to the aviation body, hence judged mission accuracy using the actual flight test. The design process and the mission evaluation process employed in this study can be utilized on the development of various unmanned aerial vehicle.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권1호
• /
• pp.94-100
• /
• 2012

본 연구는 벽면 근처에 놓인 정방형주의 모서리에 수직 분할판을 부착하여 유체력 제어 효과를 양항력 측정실험 및 PIV에 의한 가시화 실험으로 조사한 것이다. 분할판의 폭은 정방형주 폭의 10% 로 했다. 실험변수로서는 수직 분할판의 부착 위치 및 벽면과 사각주 사이의 간격으로 하였다. 정방형주 중심에서 후류방향으로 3.0B(B: 정방형주 한 변 길이) 떨어진 곳에서 와도의 변화가 가장 명확했다. 수직 분할판의 위치 및 유무와 관계없이 간격비 0.4~0.6에서 평균양력계수 및 Strouhal 수의 변곡점이 나타났다. 정방형주 윗면의 뒷 모서리에 수직 분할판을 설치한 경우 항력이 감소하였으며 각 간격비 평균 5.0%의 항력 저감 효과를 얻었다. 정방형주 윗면 박리영역의 크기는 앞쪽 모서리에 수직 분할판을 설치한 경우가 가장 컸고, 원형의 정방형주, 뒷쪽 모서리에 수직 분할판을 설치한 순서로 작았으며, 평균항력계수는 이 박리영역의 크기에 비례했다.

• The Journal of Korean Physical Therapy
• /
• 제26권6호
• /
• pp.449-452
• /
• 2014

Purpose: The purpose of this study was to analyze the coordination between trunk flexion and lower limb extension contributing to vertical propulsion during sit-to-stand (STS) at different chair heights in the elderly. Methods: Ten elderly subjects were asked to stand up at their natural speed from different chair heights : (1) $90^{\circ}$ knee flexion; (2) $100^{\circ}$ knee flexion; (3) $110^{\circ}$ knee flexion; and (4) $120^{\circ}$ knee flexion. A standard chair without a backrest or armrests was used in this study. To remove inertial effects of upper limb movements, subjects were asked to stand up from a chair with their arms crossed at the chest. Mean of results of three trials were used in the analysis at different knee flexion angles. Distances moved by the shoulder for compensatory trunk movement was recorded by motion analysis and vertical force was recorded under foot using force plates. Distances moved by the shoulder and vertical ground reaction force measurements were analyzed using repeated ANOVA. Results: Distances moved by the shoulder significantly decreased with higher chair (p<0.05). Vertical forces were not significant difference on chair heights (p>0.05), but results of pairwise comparisons for vertical force revealed significant difference between $90^{\circ}$ knee flexion and $120^{\circ}$ knee flexion (p<0.05). Conclusion: Trunk movement is probably used as a compensatory mechanism at low chair heights to increase lift-off from sitting by the elderly.

• 수산해양기술연구
• /
• 제51권1호
• /
• pp.26-34
• /
• 2015

The angle of attack of a cambered otter board in a bottom trawl was estimated using a three-dimensional semi-analytic treatment of a towing cable (warp) system that was applied to the field experiments of a bottom trawl obtained by the Scanmar system. The equilibrium condition of the horizontal component and vertical component of forces was used to the three forces acting on the otter board in the horizontal plane. Those forces were the force on the warp at the bracket, hydrodynamic lift and drag forces on the otter board and the force on the hand rope attached just behind the otter board. Also the equilibrium of moment about the front edge of the otter board was used to find out the angle of attack of the cambered otter board. When the warp length was 120m and 180m long and the towing speed was between 1.23 and 1.90 m/s, the estimated angle of attack of the cambered otter board was ranged between $26.1^{\circ}$ and $29.6^{\circ}$, respectively, though the maximum lift force was at the angle of attack $22.6^{\circ}$. The angle of attack of the otter board was tended to increase weakly with the longer length of warp (180 m) at the same towing speed in the experiment.

• Wind and Structures
• /
• 제26권4호
• /
• pp.191-204
• /
• 2018

This article presents a study of the largest-ever (height = 220 m) cooling tower using the large eddy simulation (LES) method. Information about fluid fields around the tower and 3D aerodynamic time history in full construction process were obtained, and the wind pressure distribution along the entire tower predicted by the developed model was compared with standard curves and measured curves to validate the effectiveness of the simulating method. Based on that, average wind pressure distribution and characteristics of fluid fields in the construction process of ultra-large cooling tower were investigated. The characteristics of fluid fields in full construction process and their working principles were investigated based on wind speeds and vorticities under different construction conditions. Then, time domain characteristics of ultra-large cooling towers in full construction process, including fluctuating wind loads, extreme wind loads, lift and drag coefficients, and relationship of measuring points, were studied and fitting formula of extreme wind load as a function of height was developed based on the nonlinear least square method. Additionally, the frequency domain characteristics of wind loads on the constructing tower, including wind pressure power spectrum at typical measuring points, lift and drag power spectrum, circumferential correlations between typical measuring points, and vertical correlations of lift coefficient and drag coefficient, were analyzed. The results revealed that the random characteristics of fluctuating wind loads, as well as corresponding extreme wind pressure and power spectra curves, varied significantly and in real time with the height of the constructing tower. This study provides references for design of wind loads during construction period of ultra-large cooling towers.

• 한국건축시공학회지
• /
• 제21권1호
• /
• pp.41-49
• /
• 2021

본 연구는 최근 고층 건축물의 외장 마감으로 사용되는 커튼월 중, 유니트 커튼월 방식의 양중 문제 해결을 위하여 커튼월의 수직부재인 멀리온을 레일로 활용하고자 하였다. 커튼월 멀리온의 레일 적용에 따른 양중 가능 여부는 Mock-Up Test의 진행을 통해 20m/sec의 풍속에도 양중이 가능한 것으로 나타났으며, 비교를 위해 선정된 현장 기준으로 공사 기간은 약 20% 단축이 가능하며 투입 인원은 약 33%를 줄일 수 있을 것으로 분석되었으며, 10,000㎡의 설치를 가정하면 80% 이상의 시공비용 절감이 가능한 공법으로 판단된다.

• 한국항해항만학회지
• /
• 제35권3호
• /
• pp.197-204
• /
• 2011

회류수조에서의 대각도 정적(static) 모형실험을 통해 Manta형 무인잠수체에 작용하는 동유체력을 측정하였으며, 동유체력에 미치는 Reynolds수의 영향을 고찰하였다. 이를 위해 동유체력을 cross-flow drag과 양력(lift force)으로 성분 분석을 하였으며, 양력 성분에는 Reynolds수의 영향을 무시하고, cross-flow drag 성분에만 Reynolds수의 영향을 고려하였다. 그 후 이들 두 성분을 다시 합성함으로써 실물 무인잠수정에 작용하는 동유체력의 추정 기법을 제시하였다.