• 조명전기설비학회논문지
• /
• 제21권6호
• /
• pp.19-25
• /
• 2007

특정한 배광 구현을 위하여 부피를 갖는 실제 광원에 대한 프리즘 설계법을 연구하였다. 입사각을 알고 목표 방향으로 광선을 보내려 할 때, 프리즘 정각을 구하는 수식을 유도하였고, 순차적으로 프리즘 정각을 구하였다. 점광원으로 가정한 설계 결과의 문제점을 분석한 후 이를 보완하여 부피를 갖는 광원에 적용할 수 있는 설계법을 도출하였다. 각각의 설계 결과로 나온 배광과 효율을 비교, 분석하였고 보완된 설계법을 통해 개선된 결과를 얻을 수 있었다.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제16권2호
• /
• pp.37-43
• /
• 2008

The air and water flow distributions are experimentally studied for a round header - ten flat tube configuration. Three different inlet orientation modes (parallel, normal, vertical) were investigated. Tests were conducted with downward flow configuration for the mass flux from 70 to $130kg/m^2s$, quality from 0.2 to 0.6, non-dimensional protrusion depth (h/D) from 0,0 to 0.5. It is shown that, for almost all the test conditions, vertical inlet yielded the best flow distribution, followed by normal and parallel inlet. Possible explanation is provided using flow visualization results.

• 한국해양학회지:바다
• /
• 제3권3호
• /
• pp.142-148
• /
• 1998

심해저 망간단괴 채광에 따른 저층생태환경의 변화를 평가하기 위한 기초환경연구의 일환으로 북동적도 태평양 심해저 퇴적물 내의 총 ATP(T-ATP), 용존 ATP(D-ATP) 그리고 입자성 ATP(P-ATP)의 농도 및 수직분포양상을 연구하였다. T-ATP는 퇴적물 6 cm 깊이 내에서 4.4~40.6, D-ATP는 0.6~16.1, 그리고 P-ATP는 3.0~29.2 ng/g dry sediment의 범위로 변했다. T-ATP의 약 84%, D-ATP의 약 81% 그리고 P-ATP의 약 74%가 표층 퇴적물 2 cm 이내에 분포하는 것으로 나타났으며, 분포양상이 퇴적물 내의 함수율과 높은 상관관계를 나타냈다. 이러한 결과는 심해저 퇴적물 내의 미생물(P-ATP) 분포가 수층으로부터 전달되는 유기탄소에 의해 결정됨을 의미한다. 다중주상 시료채집기를 사용해 획득한 퇴적물에서 P-ATP 최대층이 0~0.5 cm 깊이 내에 존재하는 것으로 나타나, 표층이 교란되는 상자형 퇴적물 채집기보다는 다중주상 시료채집기가 심해저 퇴적물내 ATP의 미세수직구조의 연구를 위해서 더욱 효과적인 것으로 판명되었다. 결론적으로 ATP 농도가 퇴적물 깊이 6cm 이내에서 뚜렷한 수직분포양상을 보이는 것으로 미루어, ATP 분포양상이 향후 심해저 광업에 따른 미생물 생체량 변화를 평가하기 위한 유용한 환경기초자료로 사용될 수 있는 것으로 나타났다.

• Ocean and Polar Research
• /
• 제26권2호
• /
• pp.367-376
• /
• 2004

Macrobenthos were collected at 7 stations located from $5^{\circ}N$ to $10^{\circ}N$ with 1o interval along the longitude of $131^{\circ}W$ using a box corer with sampling area of $0.25\;m^2$ in July, 1999. In order to see the vertical distribution of macrobenthos in sediments, each subcore sample was divided into 5 layers with 1 cm interval up to 6 cm depth. Each subcore sample was sieved through 0.3 mm mesh screen and fixed with 10% Rose Bengal added formalin. A total of 22 faunal groups in 11 phyla were sampled and the average density was $959\;{\pm}\;584\;ind./m^2$. Foraminiferans comprised 34.8% of total specimens were the most abundant fauna, and followed by nematodes (27.5%), polychaete worms (15.7%), and benthic harpactoid copepods (10.4%). A latitudinal trend was shown in the distribution of macrobenthos; the maximum density of $1,832\;ind./m^2$ appeared at station N06 and the most poverished community occurred at station N09 with the density of $248\;ind./m^2$. The density of typical macrofaunal taxa except foraminiferans and nematods was $116\;ind./m^2$. In the vertical distribution of macrobenthos, more than 70% of macrobenthos occurred in the upper 2 cm layer, and upper 4 cm layer contained about 90% of macrofauna. Polychaete worms consisted of 22 families, and cirratulid and paraonid worms were dominant polychaete species. The prominant feeding guilds of polychaete worms were SDT (surface, descretely motile, tenaculate feeding) and SMX (surface, motile, non-jawed); they comprised more than 50% of polychaete abundance. These feeding guilds of polychaete worms suggests that the deep sea benthos should be well adapted the newly settled deposits from water column, but this should be clarified by the further studies.

• 한국응용곤충학회지
• /
• 제31권2호
• /
• pp.101-112
• /
• 1992

덕유산 지역의 개미의 분포와 개미상을 밝히기 위하여 덕유산 지역을 5개 코스로 나누어 1986년, 1989년, 1991년의 3개년간 16차례에 걸쳐 476 colony를 채집하여 4아과 22속 44종의 분포를 확인하였다. 아과별 종조성은 두마디개미아과가 12속 21종으로 가장 많고 불개미아과가 6속 20종, 침개미아과가 3속 4종, 시베리아개미아과가 1속 1종 이었다. 수직분포의 경향은 고도 500 m에서 전체종의 93%인 41종의 집중 분포하고 있었으며 종별수직분포의 상한계선은 고도 700 m에서 일본침개미와 장구개미를 포함한 5종, 고도 1,000 m에서는 침개미, 호리가슴개미, 나도누은털개미, 스미드개미를 포함하여 10종이 분포하고 있었다.

• 한국해양학회지
• /
• 제12권1호
• /
• pp.7-12
• /
• 1977

Vertical mixing in the ocean affects the formation of water masses as well as the vertical distribution of nutrients and dissolved substances. this study is to investigate the effect of stability on the intensity of vertical transfer in the case of shallow and straitfied channel. It is found that the relation of the stability and vertical turbulent diffusion is given by K$\sub$z/ = -${\beta}$-(c+${\beta}$) / ${\alpha}$(E-1/${\alpha}$) where K$\sub$z/ and E denotes the vertical turbulent diffusion coefficient and stability, respectively. The empirical coefficients ${\alpha}$, ${\beta}$ and c depend on the magnitude of vertical components and stability, i.e., through thermocline intensity. The study indicates that the diffusivity of the surface mixed layer is (K$\sub$z/)=300∼1,200$\textrm{cm}^2$/sec, the thermocline layer is (K$\sub$z/)= 50∼200$\textrm{cm}^2$/sec and the cold layer is (K$\sub$z/)=200∼600$\textrm{cm}^2$/sec based on near- minimum least-squares error estimates from the regression analysis. An important result of our study comes out that the model is in accordance with the general trends of the effect of stability on the vertical turbulent diffusion coefficients in the case of shallow and strongly stratified channel.

• 한국지진공학회논문집
• /
• 제20권6호
• /
• pp.413-424
• /
• 2016

The vertical design spectrum for Korea, which is known to belong to an intra-plate region, is developed from the ground motion records of the earthquakes occurred in Korea and overseas intra-plate regions. From the statistical analysis of the vertical response spectra, a mean plus one standard deviation spectrum in lognormal distribution is obtained. Regression analysis is performed on this curve to determine the shape of spectrum including transition periods. The developed design spectrum is valid for the estimation both spectral acceleration and displacement. The ratio of vertical to horizontal response spectrum for each record is calculated. Statistical analysis of the ratios rendered the vertical to horizontal ratio (V/H ratio). Subsequently the ratio between the peak vertical ground acceleration to the horizontal one is obtained.

• 대한치과보철학회지
• /
• 제34권1호
• /
• pp.31-69
• /
• 1996

The purpose of this investigation was to analyze stress distribution in implant supporting tissue according to different types of attachments such as combination bar attachment, Hader bar attachment, O-Ring attachment and Dal-Ro attachment that are used in mandibular overdenture by using two osseointegrated implants, to study the influence that POM IMC used in bar type attachment has in implant supporting tissue and compare the preceding analyses to find out an effective stress distribution method. Three dimensional photoelastic method was used to obtain the following results. (A) Analysis of stress distribution according to attachment type 1. Under vertical load condition, compressive stress was seen at implant supporting area of working side on all the photoelastic models but in Hader bar attachment tensional stress was seen at distal upper area of implant supporting area. Relatively Hader bar and O-Ring attachment showed even stress distribution pattern. 2. Under vertical load condition, compressive stress at implant apex area and tensional stress at implant lateral supporting area were seen at nonworking side of all models. 3. Under $25^{\circ}$ lateral load condition, general compressive stress was seen at working side implant supporting area in most of the models, especially at distal upper supporting area higher compressive stress concentration was seen in combination bar attachment and tensional stress concentration, in Hader bar attachment. 4. Under $25^{\circ}$ lateral load condition, compressive stress at implant apex area and tensional stress at implant lateral supporting area were seen at nonworking side of all models, except O-Ring model which showed compressive stress only. (B) Influence of POM IMC to stress distribution in bar type attachment 5. Under vertical load condition, better stress distribution pattern was seen at working side of combination bar and Hader bar attachment model using POM IMC. 6. Under vertical load condition, stress value was increased at nonworking side of combination bar attachment model using POM IMC and tendency of increasing compression was seen at nonworking side of Hader bar attachment model using POM IMC. 7. Under $25^{\circ}$ lateral load condition, better stress distribution pattern was seen at working side of combination bar attachment model using POM IMC but tendency of increasing stress was seen on working side of Hader bar attachment model using POM IMC. 8. Under $25^{\circ}$ lateral load condition, stress reduction was seen at nonworking side of combination bar attachment model using POM IMC but tendency of increasing stress was seen at nonworking side of Hader bar attachment model using POM IMC.

• 한국유통학회지:유통연구
• /
• 제16권5호
• /
• pp.211-231
• /
• 2011

상업론의 전통을 이어받은 일본 마케팅학계의 선구자들은 과점(寡占)메이커가 구축한 유통계열화에 대해 중소상인을 배급자로 전락시킨다고 하여 비판적이었고, 멀지 않은 장래에 붕괴될 것으로 예견했다. 한편 이러한 규범론적 연구그룹에 대해 거의 모든 소비재업계에 보편적으로 존재하는 유통계열화야 말로 미국식 마케팅 전략의 진수라고 평가하는 실증주의 연구그룹도 존재했다. 일본의 유통경로연구는 이러한 전통적인 규범주의 연구와 미국의 영향을 받은 경험주의 연구의 건전한 대립에 의해 발전하였다. 특기해야 할 것은 대형소매기업의 대두가 본격화되는 1980년대에 들어와 유통계열화가 약체화하기 시작했다는 점과 그 반면에 오랫동안 대립관계에 있었던 과점메이커와 대형소매기업간의 파트너십관계가 진전되기 시작했다는 점이다. 이에 따라 일본의 유통경로연구의 입장은 크게 변했다. 유통계열화라는 연구대상이 소멸했다고 판단했기 때문에 종래 이를 비판하고 상인옹호론을 펼쳤던 규범적 연구자들이 대형소매기업이 주도권을 가지는 제판동맹(製販同盟)을 긍정적으로 받아들인 것이다. 한편 유통계열화의 순기능을 지지했던 경험적 연구자들도 태도를 바꾸었다. 실증주의의 가르침에 따라 제판동맹이라는 새로운 실천현상을 연구의 프론티어로 인식한 것이다. 이처럼 일본의 유통경로연구가 일제히 유통계열화에서 제판동맹으로 연구의 중점을 이동시키면서, 방법론적으로 규범주의를 옹호하는 연구자는 그 모습을 감추고 다투어 경험주의 연구에 치중하게 된다. 일본적 마케팅의 주역으로서 규범주의적 색채를 남겼던 유통경로연구 조차도 방법론적으로 전향하게 된 것이다. 본고는 유통계열화의 종언을 전제로 하는 이러한 일본유통경로연구의 움직임에 대해 비판적인 견해를 피력한다.

• The Journal of Advanced Prosthodontics
• /
• 제13권2호
• /
• pp.79-88
• /
• 2021

Purpose. To assess peri-implant stress distribution using finite element analysis in implant supported fixed partial denture with occlusal schemes of cuspally loaded occlusion and implant protected occlusion. Materials and methods. A 3-D finite element model of mandible with D2 bone with partially edentulism with unilateral distal extension was made. Two Ti alloy identical implants with 4.2 mm diameter and 10 mm length were placed in the mandibular second premolar and the mandibular second molar region and prosthesis was given with the mandibular first molar pontic. Vertical load of 100 N and and oblique load of 70 N was applied on occlusal surface of prosthesis. Group 1 was cuspally loaded occlusion with total 8 contact points and Group 2 was implant protected occlusion with 3 contact points. Results. In Group 1 for vertical load, maximum stress was generated over implant having 14.3552 Mpa. While for oblique load, overall stress generated was 28.0732 Mpa. In Group 2 for vertical load, maximum stress was generated over crown and overall stress was 16.7682 Mpa. But for oblique load, crown stress and overall stress was maximum 22.7561 Mpa. When Group 1 is compared to Group 2, harmful oblique load caused maximum overall stress 28.0732 Mpa in Group 1. Conclusion. In Group 1, vertical load generated high implant stress, and oblique load generated high overall stresses, cortical stresses and crown stresses compared to vertical load. In Group 2, oblique load generated more overall stresses, cortical stresses, and crown stresses compared to vertical load. Implant protected occlusion generated lesser harmful oblique implant, crown, bone and overall stresses compared to cuspally loaded occlusion.