• Structural Engineering and Mechanics
• /
• v.59 no.4
• /
• pp.719-737
• /
• 2016

The present study investigated the earthquake behavior of R/C structures considering the vertical earthquake motion with the help of a comparative study. For this aim, the linear time-history analyses of a high-rise R/C structure designed according to TSC-2007 requirements were conducted including and excluding the vertical earthquake motion. Earthquake records used in the analyses were selected based on the ratio of vertical peak acceleration to horizontal peak acceleration (V/H). The frequency-domain analyses of the earthquake records were also performed to compare the dominant frequency of the records with that of the structure. Based on the results obtained from the time-history analyses under the earthquake loading with (H+V) and without the vertical earthquake motion (H), the value of the overturning moment and the top-story vertical displacement were found to relatively increase when considering the vertical earthquake motion. The base shear force was also affected by this motion; however, its increase was lower compared to the overturning moment and the top-story vertical displacement. The other two parameters, the top-story lateral displacement and the top-story rotation angle, barely changed under H and H+V loading cases. Modal damping ratios and their variations in horizontal and vertical directions were also estimated using response acceleration records. No significant change in the horizontal damping ratio was observed whereas the vertical modal damping ratio noticeably increased under H+V loading. The results obtained from this study indicate that the desired structural earthquake performance cannot be provided under H+V loading due to the excessive increase in the overturning moment, and that the vertical damping ratio should be estimated considering the vertical earthquake motion.

• The Journal of the Korea Contents Association
• /
• v.8 no.11
• /
• pp.1-9
• /
• 2008

Thanks to the multimedia technology development, it is possible to show image representations in high quality and to process images in various ways. Anisotropic diffusion as an effective diffusion filtering among many image preprocessing methods and postprocessing methods is used in reduction of speckle noises of ultrasound images, image restoration, edge detection, and image segmentation. However, the conventional anisotropic diffusion based on a cross-kernel causes the following problems. The problem is the concentration of edges in the vertical or horizontal directions. In this paper, a new anisotropic diffusion transform based on directions of gradient is proposed. The proposed method uses the eight directional square-kernel which is an expanded form of the cross-kernel. The proposed method is to select directions of small gradient based on square-kernel. Therefore, the range of proposed diffusion is selected adaptively according to the number of the directions of gradient. Experimental results show that the proposed method can decrease the concentration of edges in the vertical or horizontal directions, remove impulse noise. The image in high quality can be obtained as a result of the proposed method.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.155-160
• /
• 2002

Recently, the development of aerospace and automobile industries has brought new technological challenges, rebated to the growing complexity of products and the new geometry of the models. High speed milling with a 5-Axis milling machine has been widely used fur 3D sculptured surface parts. When turbine blades are machined by a 5-axis milling, their thin and cantilever shape causes vibrations, deflections and twists. Therefore, the surface roughness and the waviness of the workpiece are not good. In this paper, the effects of cutter orientation and the lead/tilt angle used to machine turbine blades with a 5-axis high speed ball end-milling were investigated to improve geometric accuracy and surface integrity. The experiments were performed using a lead/tilt angle of 15$^{\circ}$ to the workpiece with four cutter directions such as horizontal outward, horizontal inward, vertical outward, and vortical inward directions. Workpiece deflection, surface roughness and the machined surface were all measured with various cutter orientations such as cutting directions, and lead/tilt angle. The results show that the best cutting strategy for machining turbine blades with a 5-axis milling is horizontal inward direction with a tilt angle.

• Journal of Digital Contents Society
• /
• v.16 no.3
• /
• pp.463-470
• /
• 2015

The angular dependence of active dosimeters, EPD, is analysed and compared with that of passive dosimeters, OSLD, after evaluating their relative response and uncertainty of measurement, where it is known that the personal use of them has been increased recently. There appeared a minor variation for average relative response of OSLD in the horizontal and vertical directions within the range $0^{\circ}{\sim}{\pm}90^{\circ}$, which are 0.97 and 0.95 respectively. The variations of angular dependence in the same situations with OSLD are 0.65 and 0.62, respectively, which also reveals a negligible effect on the overall uncertainty. EPDs within the interval $0^{\circ}{\sim}{\pm}60^{\circ}$ for horizontal and vertical directions are 0.94 and 0.97, respectively. These satisfy the requirements of IEC 61526. Uncertainties about the dependence of direction from horizontal and vertical directions are 0.44, 0.40, respectively. The impact of these uncertainties on the overall uncertainty was negligible. However, we observed a significant change in reactivity: the relative reactivities for $+90^{\circ}$ and $-90^{\circ}$ from the horizontal direction are 0.60, 0.37, while that form vertical direction is 0.06. The direction dependence of OSLD was superior to EPD in the range of $0^{\circ}{\sim}{\pm}90^{\circ}$. There appeared a rapidly changing structural features in EPD response for a certain direction. Therefore, we conclude that concurrent use of passive dosimeters and auxiliary dosimeter provides accurate data for personal dose measurements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.106.1-106.1
• /
• 2013

When strong static magnetic field is applied to the TMP, it is expected that the presence of the magnetic field might retard the velocity of the blades which results in the change of the pumping speed of the TMP. However, such effect of the magnetic field on the TMP has not been well characterized. Thus, under the strong magnetic field, monitoring pumping speed as well as generated heat, pressure, and vibration of the TMP may be an important issue to understand the magnetic field tolerance of the TMP and the development of magnetic shielding technique for the key components of the pump. For this purpose, magnetic field generation system to the vertical direction by a circular current source was firstly designed and suggested [K. Baik et al., 44th Annual Conf. KVS, 22(1), 153, (2012)]. In the current study, another magnetic field generation systems are presented to apply the magnetic field to the horizontal and radial directions by the rectangular current sources and the permanent magnets respectively. Such systems were made to generate at least 50 Gauss of magnetic field along the vertical direction and at least 25 Gauss of magnetic field along the horizontal or radial direction. Current study introduces the evaluation system of the magnetic field along the vertical, horizontal, and radial directions and presents the measured experimental results of the magnetic field when such systems are combined with the equipment where TMP will be installed.

• Wind and Structures
• /
• v.10 no.1
• /
• pp.1-22
• /
• 2007

The suppression of aerodynamic response of long-span suspension bridges during erection and after completion by using single TMD and multi TMD is presented in this paper. An advanced finite-element-based aerodynamic model that can be used to analyze both flutter instability and buffeting response in the time domain is also proposed. The frequency-dependent flutter derivatives are transferred into a time-dependent rational function, through which the coupling effects of three-dimensional aerodynamic motions under gusty winds can be accurately considered. The modal damping of a structure-TMD system is analyzed by the state-space approach. The numerical examples are performed on the Akashi Kaikyo Bridge with a main span of 1990 m. The bridge is idealized by a three-dimensional finite-element model consisting of 681 nodes. The results show that when the wind velocity is low, about 20 m/s, the multi TMD type 1 (the vertical and horizontal TMD with 1% mass ratio in each direction together with the torsional TMD with ratio of 1% mass moment of inertia) can significantly reduce the buffeting response in vertical, horizontal and torsional directions by 8.6-13%. When the wind velocity increases to 40 m/s, the control efficiency of a multi TMD in reducing the torsional buffeting response increases greatly to 28%. However, its control efficiency in the vertical and horizontal directions reduces. The results also indicate that the critical wind velocity for flutter instability during erection is significantly lower than that of the completed bridge. By pylon-to-midspan configuration, the minimum critical wind velocity of 57.70 m/s occurs at stage of 85% deck completion.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.12
• /
• pp.21-26
• /
• 2013

In this paper, We are suggested methods of feature extraction in molecular images. The result of image transform DWT examination by suggested method, we are obtained as follows. 1-level and 2-levels of decomposition results showed the composition of the low frequency region. But, 3-level decomposition results did not appear in the data component is almost. Observed not with the naked eye is not, but the 3-level output data values of the results were decomposed. We are printed the horizontal and vertical directions of low-frequency region of the data, the high frequency region of the horizontal and vertical data, and diagonal high frequency region of the horizontal and vertical directions data. If the output data using molecular imaging and CT, PET, MR imaging will be compared with the data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.2
• /
• pp.211-224
• /
• 1994

In this paper, a multi-level adaptive intraframe method has been proposed to separate the luminance and chominance components in NTSC composite signal. The control signals are generated by detecting the vertical correlation and transition in the horizontal and diagonal directions. The chrominance component is adaptively processed through vertical and horizontal filters according to the control signals and the luminance component is processed by subtracting the chrominance component from the composite video signal. The several filters have been used at the sampling rate of four times the color subcarrier frequency and computer simulation and SVP(Serial Video Processing) system have been introduced to compare the performance of the conventional methods and that of proposed one.

• Journal of Technology Innovation
• /
• v.23 no.2
• /
• pp.81-100
• /
• 2015

The aim of this study is to investigate the effect of factors hampering innovation on firm's R&D cooperation. We classify the obstacles to innovation into lack of money and information, and also distinguish between horizontal cooperation and vertical cooperation. We argue that different obstacles have a differential effect on the types of R&D cooperation. We examined the hypotheses using KIS (Korea Innovation Survey) data. The results show that deficiency of information is positively related to both vertical and horizontal cooperation, however, lack of money is not related to firm's R&D cooperation. Based on these findings from Korean manufacturing firms, the implications of the results and future research directions are discussed.

• The korean journal of orthodontics
• /
• v.54 no.2
• /
• pp.108-116
• /
• 2024

Objective: A three-dimensional-printed individual titanium plate was applied for maxillary protraction to eliminate side effects and obtain the maximum skeletal effect. This study aimed to explore the stress distribution characteristics of sutures during maxillary protraction using individual titanium plates in various directions and locations. Methods: A protraction force of 500 g per side was applied at forward and downward angles between 0° and 60° with respect to the Frankfort horizontal plane, after which the titanium plate was moved 2 and 4 mm upward and downward, respectively. Changes in sutures with multiple protraction directions and various miniplate heights were quantified to analyze their impact on the maxillofacial bone. Results: Protraction angle of 0-30° with respect to the Frankfort horizontal plane exhibited a tendency for counterclockwise rotation in the maxilla. At a 40° protraction angle, translational motion was observed in the maxilla, whereas protraction angles of 50-60° tended to induce clockwise rotation in the maxilla. Enhanced protraction efficiency at the lower edge of the pyriform aperture was associated with increased height of individual titanium plates. Conclusions: Various protraction directions are suitable for patients with different types of vertical bone surfaces. Furthermore, when the titanium plate was positioned lower, the protraction force exhibited an increase.