• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.2
• /
• pp.59-70
• /
• 2022

In this paper, a GPS/GF-INS integrated navigation system is proposed, in which the high rate attitude aiding signal, the high rate position and velocity aiding of GPS receiver is used for the cube structure of the GF-IMU, effectiveness of the proposed GPS/GF-INS integrated navigation system was shown when the vehicle follows two trajectories, circling and spiraling. Performance evaluation results show that the proposed GPS/GF-INS integrated navigation method gives better navigation outputs when the attitude output of GPS is used and more better navigation outputs are obtained when the rate of GPS aiding signal is higher.

• The Journal of Korea Robotics Society
• /
• v.18 no.1
• /
• pp.72-81
• /
• 2023

We introduce tightly-coupled GNSS-LiDAR-Inertial state estimator, which is capable of SLAM (Simultaneously Localization and Mapping) and autonomous driving. Long term drift is one of the main sources of estimation error, and some LiDAR SLAM framework utilize loop closure to overcome this error. However, when loop closing event happens, one's current state could change abruptly and pose some safety issues on drivers. Directly utilizing GNSS (Global Navigation Satellite System) positioning information could help alleviating this problem, but accurate information is not always available and inaccurate vertical positioning issues still exist. We thus propose our method which tightly couples raw GNSS measurements into LiDAR-Inertial SLAM framework which can handle satellite positioning information regardless of its uncertainty. Also, with NLOS (Non-light-of-sight) satellite signal handling, we can estimate our states more smoothly and accurately. With several autonomous driving tests on AGV (Autonomous Ground Vehicle), we verified that our method can be applied to real-world problem.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.3
• /
• pp.588-594
• /
• 2015

Although GPS technology for location positioning system has been widely used, it is difficult to be used in intelligent transport systems, due to the large positioning error and limited area for receiving radio signals. Thanks to the rapid development of LED technology, LED lights become popular in many applications. Especially, visible light communications (VLC) has raised a lot of interests because of the simultaneous functioning of LED illumination and communication. Recent studies on positioning system using VLC mainly focused on indoor environments and still difficult to satisfy positioning accuracy and simple implementation simultaneously. In this paper, we propose a positioning system based on VLC using the coordinate information of LEDs installed on the road infrastructure. Extracting the LED signal, obtained through VLC, from the easily accessible camera image, it is possible to estimate the position of the car on the road. Simulation results show that the proposed scheme can achieve a high positioning accuracy of 1 m when large number of pixels is utilized and the distance from the LED light is close.

• Journal of Advanced Navigation Technology
• /
• v.16 no.6
• /
• pp.927-934
• /
• 2012

In this paper, we present relative positioning algorithm for moving land vehicle using GPS, MEMS IMU and B-CDMA module. This algorithm does not calculate precise absolute position but calculates relative position directly, so additional infrastructure and I2V communication device are not required. Proposed algorithm has several steps. Firstly, unbiased relative position is calculated using pseudorange difference between two vehicles. Simultaneously, the algorithm estimates position of each vehicle using GPS/INS integration. Secondly, proposed algorithm performs filtering and finally estimates relative position and relative velocity. Using proposed algorithm, we can obtain more precise relative position for moving land vehicles with short time interval as IMU sensor has. The simulation is performed to evaluate this algorithm and the several field tests are performed with real time program and miniature vehicles for verifying performance of proposed algorithm.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.89-93
• /
• 2003

The Korea Research Institute of Ships and Ocean Engineering (KRISO), the ocean engineering branch of KORDI, has designed and manufactured a model of an autonomous underwater vehicle (AUV) to test underwater docking. This paper introduces the AUV model, ASUM, equipped with a visual servo control system to dock into an underwater station with a camera and motion sensors. To make a visual servoing AUV, this paper implemented the visual servo control system designed with an augmented state equation, which was composed of the optical flow model of a camera and the equation of the AUV's motion. The system design and the hardware configuration of ASUM are presented in this paper. A small long baseline acoustic positioning system was developed to monitor and record the AUV's position for the experiment in the Ocean Engineering Basin of KRISO, KORDI. ASUM recognizes the target position by processing the captured image for the lights, which are installed around the end of the cone-type entrance of the duct. Unfortunately, experiments are not yet conducted when we write this article. The authors will present the results for the docking test of the AUV in near future.

• International Journal of Automotive Technology
• /
• v.8 no.6
• /
• pp.753-760
• /
• 2007

In this paper, a roll and pitch estimation algorithm using a set of accelerometers and wireless sensor networks(S/N) is presented for use in a passenger vehicle. While an inertial measurement unit(IMU) is generally used for roll/pitch estimation, performance may be degraded in the presence of longitudinal acceleration and yaw motion. To compensate for this performance degradation, a new roll and pitch estimation algorithm is proposed that uses an accelerometer array, global positioning system(GPS) and in-vehicle networks to get information from yaw rate and roll rate sensors. Angular acceleration and roll and pitch approximation are first calculated based on vehicle kinematics. A discrete Kalman filter is then applied to estimate both roll and pitch more precisely by reducing noise from the running engine and from road disturbance. Finally, the feasibility of the proposed algorithm is shown by comparing its performance experimentally with that of an IMU in the framework of an indoor test platform as well as a test vehicle.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.2 s.63
• /
• pp.82-89
• /
• 2005

This study deals with the development of the extended Kalman filter(EKF) algorithm for the localization of underwater mining vehicles. Both simulation and experimental studies in a test bed are carried out. For the experiments, a scale dawn tracked vehicle is run in a soil bin containing cohesive soil of bentonite-water mixture. To develop the EKF algorithm, we use a kinematic model including the inner/outer track slips and the slip angle for the vehicle. The measurements include the inner and outer wheel speeds from encoders, the heading angle from a compass sensor and a fiber optic rate gyro, and x and y coordinate position values from a vision system. The vision sensor replaces the LBL(Long Base Line) sonar system used in the real underwater positioning situations. Artificial noise signals mimicking the real LBL noise signal are added to the vision sensor information. To know the mean slip values of the tracks in both straight and cornering maneuver, several trial running experiments are executed before applying the EKF algorithm. Experimental results show the effectiveness of the EKF algorithm in rejecting the sensor measurements noise. Also, the simulation and experimental results show close correlations.

• International Journal of Automotive Technology
• /
• v.7 no.1
• /
• pp.83-90
• /
• 2006

The purpose of this paper is to describe the design and implementation of an unmanned ground vehicle, called the TailGator at CIMAR (Center for Intelligent Machines and Robotics) of the University of Florida. The TailGator is a gas powered, four-wheeled vehicle that was designed for the AUVSI Intelligent Ground Vehicle Competition and has been tested in the contest for 2 years. The vehicle control model and design of the sensory systems are described. The competition is comprised of two events called the Autonomous Challenge and the Navigation Challenge: For the autonomous challenge, line following, obstacle avoidance, and detection are required. Line following is accomplished with a camera system. Obstacle avoidance and detection are accomplished with a laser scanner. For the navigation challenge, waypoint following and obstacle detection are required. The waypoint navigation is implemented with a global positioning system. The TailGator has provided an educational test bed for not only the contest requirements but also other studies in developing artificial intelligence algorithms such as adaptive control, creative control, automatic calibration, and internet-base control. The significance of this effort is in helping engineering and technology students understand the transition from theory to practice.

• The Journal of the Korea Contents Association
• /
• v.6 no.5
• /
• pp.14-19
• /
• 2006

In this paper, we describe an arrival time guidance system of circular vehicles using GPS, CDMA and TCP/IP technology. The on-board equipment consists of a GPS receiver and a PDA phone. The on-board equipment sends the current position data of the vehicle to the positioning server via CDMA and Internet. The server predicts the arrival time to the next bus-stop. Any user can lookup the current position and the predicted arrival time of the vehicle utilizing his mobile phone, PDA phone, or Web.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.355-357
• /
• 2022

In this paper, as a positioning technology for predicting the movement path of a moving object using a recurrent neural network (RNN) model, which is a deep learning network, in an indoor environment, continuous location information is used to predict the path of a moving vehicle within a local path. We propose a movement path generation technique that can reduce decision errors. In the case of an indoor environment where GPS information is not available, the data set must be continuous and sequential in order to apply the RNN model. However, Wi-Fi radio fingerprint data cannot be used as RNN data because continuity is not guaranteed as characteristic information about a specific location at the time of collection. Therefore, we propose a movement path generation technique for a vehicle moving a local path in an indoor environment by giving the necessary sequential location continuity to the RNN model.