• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.169-174
• /
• 1994

This paper presents the results of a parametric study on the bearing capacity behavior of a footing located above geogrid-reinforced ground using the finite element method of analysis. A wide range of boundary conditions were analyzed, with varing geogrid design parameters such as depth of geogrid layer, length and siffness of geogrid, and number of geogrid layer, were analyzed. Based on the results of analysis, the optimum geogrid design parameters were determined, which maximize the reinforcing effect of geogrid reinforcement for a given conidition. Furthermore, the mechanistic behavior of a geogrid-reinforced ground subjected to a footing load was discussed using the results of analysis such as stress distribution, propagation of plastic yielding, displacement vector among others.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.77-79
• /
• 2008

This paper deals with extraction of design parameters of Linear Switched Reluctance Motor (LSRM) based on force calculation using space harmonic analysis, 2D Finite Element Method (FEM) and experimental measurement. First, analytical solutions for flux density due to mover winding currents are derived in terms of magnetic vector potential and a 2D rectangular coordinate system, for the case when the mover is located at aligned and unaligned position. The analytical results are compared with those obtained from a 2D FEM Second, using Fourier series expansion, this paper predicts the force profile of LSRM analytically.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.101-103
• /
• 2003

This paper deals with field distributions in high speed motor with two different types of diametrically magnetized PM rotor, one is that rotor is consisted of PM and shaft, the other is that rotor has only PM. In case of high speed motor with rotor consisted of PM and shaft, this paper predicts field distributions in high speed motor according to the quality of shaft. The magnetic field solutions are derived analytically in terms of vector potential and 2-D polar coordinate system. The results are shown in good conformity with those obtained from the commonly used finite element method.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.86-88
• /
• 2004

This paper deals with the comparison and analysis for open-circuit field of PM(permanent magnet) machines with Halbach and circumferential magnetized rotor. The governing equation is derived in terms of magnetic vector potential and 2-d polar coordinate. And then, analytical results has been verified by comparison with those obtained from FE(finite element) method. On the basis of 2-d analytical results, this paper confirms that PM machines with circumferential magnetized rotor is superior to it with Halbach magnetized rotor in terms of magnitude and sinusoidal wave-forms of flux density due to PM and required magnet volume.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.712_713
• /
• 2009

This paper deals with the analysis on eddy current looses of high speed permanent magnet synchronous motor (PMSM) for turbo compressor according to voltage source driving. This paper presents analytical procedures for calculation of the eddy current losses using Poynting theorem. On the basis of the magnetic vector potential and a two-dimensional (2-D) cylindrical coordinate system, this paper derived analytical solutions of the eddy current looses using phase current analysis. The eddy current losses of each harmonic obtained by fast Fourier transform (FFT) analysis of phase current are with results obtained from finite-element method (FEM).

• Proceedings of the KIEE Conference
• /
• 2008.10a
• /
• pp.103-104
• /
• 2008

this paper describes the electric field distribution analysis along a shield gap inner vacuum interrupter(VI). The equipotential line and electric field and field vector in a VI are analysed by a finite element method and experiment at shield gap. in result, The equipotential line and electric field distribution was affected to VI shield gap. The reason is as it gets distortion of equipotential line done. finally, this paper recognized whether or not affected, and proposed gap with the most suitable shield length and an external insulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.323-325
• /
• 1997

Conventionally it is asummed that the microstrip line conductor has a rectangular cross-section. but the additive and substactive processes used to create conductors for PCBs produce a conductor of approximately Trapezoidal cross-section. For wide Strip line, the thickness and edge effect will be small since most of capacitance is parallel plate rather than fringing and we can ignore the cross-section. For narrow strip lines, the edge effect become immportant. So in this paper, we measure the chracteristic impedance of microstripline by Vector Analyzer and simulate the electromagnetic field of microstripline using finite element method with edge angle.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.843-845
• /
• 2001

In this paper, we analyze the characteristics of electecromotive force(emf), phase current and torque according to the length of the air gap using 2nd order FEM(Finite Element Method) in Synchronous Reluctance Motor(SRH) and Brushless DC Motor(BLDC) with same volume and size. In the analysis with FEM, we applied the time-step function considering the motor switch in the magnetic vector potential of the unknown node.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.59-64
• /
• 2000

A drum type of high gradient magnetic separator was designed and optimized by computer simulations. The magnetic separator consists of high performance rare earth $(Nd_2Fe_14B)$ permanent magnets and magnetic yokes of extremely low carbon steel interconnecting the permanent magnets. Magnetic circuits of the separator were simulated for the aim of the least cost, highest magnetic strength and most efficient function by using specialized S/W (Vector Field Program) employing the Finite Element Method. The magnetic flux density was provided to be strong enough to collect the invisible fine metal particles from the surface of hot rolled steel plate with the efficiency of almost 95%.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1368-1369
• /
• 2008

This paper describes the electric field distribution analysis along a shield form inner vacuum interrupter(VI). The equipotential line and electric field and field vector in a VI are analysed by a finite element method at various shield form. in result, The equipotential line and electric field distribution was affected to VI shield gap. The reason is as it gets distortion of equipotential line done. finally, this paper recognized whether or not affected, and proposed gap with the most suitable shield length and an external insulation.