This paper is concerned with the viscous interaction between rotor and stator The viscous interaction is caused by wakes from upstream blades. The cascade was composed with five blades and cylinders were placed to make wakes and their location was about 50 percent of blade chord upstream. The location of cylinders were varied in the cascade axis with 0, 20, 40, 60 and 80 percent of pitch length. The velocity distribution in the cascade passage were measured using single slanted hot-wire and the ones in the boundary layer using boundary probe. As a result, wakes decay more rapidly at suction surface and more slowly at pressure surface. And the measurement of momentum thickness of cascade shows that the momentum thickness is larger near the blade surface. From measurement of blade boundary layer, turbulent intensity is also larger near the blade surface because wakes collide the boundary layer And wakes make boundary layer thickness smaller and delay flow separation.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2005.07a
/
pp.535-536
/
2005
Organic photovoltaic effects were studied in a device structure of ITO/CuPc/Al and ITO/CuPc/$C_{60}$/BCP/Al. A thickness of CuPc layer was varied from 10 nm to 50 nm, we have obtained that the optimum CuPc layer thickness is around 40 nm from the analysis of the current density-voltage characteristics in CuPc single layer photovoltaic cell. From the thickness-dependent photovoltaic effects in CuPc/$C_{60}$ heterojunction devices, higher power conversion efficiency was obtained in ITO/20nm CuPc/40nm $C_{60}$/Al, which has a thickness ratio (CuPc:$C_{60}$) of 1:2 rather than 1:1 or 1:3. Light intensity on the device was measured by calibrated Si-photodiode and radiometer/photometer of International Light Inc(IL14004).
The stabilization mechanism of turbulent, lifted jet flames in a non-premixed condition has been studied experimentally. The objectives are to explain the phenomenon of a liftoff height decreasing as increasing fuel velocity and to reveal the mechanisms of flame stability Hydrogen was varied from 100 to 300 m/s and a coaxial air was fixed at 16 m/s with a coflow air less than 0.1 m/s. The technique of PIV and OH PLIF was used simultaneously with CCD and ICCD cameras. It was found that the liftoff height of the jet decreased with an increased fuel jet exit velocity. The leading edge at the flame base was moving along the stoichiometric line. Finally we confirmed that the stabilization of lifted hydrogen diffusion flames is related with a turbulent intensity, which means combustion is occurred where the local flow velocity is equal to the turbulent flame propagation velocity.
Transactions of the Korean Society of Mechanical Engineers B
/
v.26
no.2
/
pp.219-226
/
2002
This paper is concerned with the effects of periodically approaching upstream wakes on cascade-flow and loss. The reduced frequency of the periodic wakes was varied in the narrow range from 0.5 to 0.7 Corresponding to a wake-passing through the cascade, two velocity deficits appeared near the boundary layer contour in the downstream from about 60% chord-length. The first velocity deficit was caused by a periodic wake and the second one appeared after some delayed time. The second velocity deficit was interpreted as the results of reattachment of flow-separation. The higher reduced frequency decreased the duration time of separation appearance and the lesser losses of blade were resulted.
We have investigated the effects of sputtering Ar gas pressure on magnetic anisotropy of Co/Pt multilayers, where sputtering Ar gas pressure was varied from 2 to 20 mTorr. The surface and volume anisotropies were found to be strongly dependent on sputtering Ar gas pressure. In particular, the surface anisotropy exhibited more than fourfold enhancement as Ar pressure was decreased from 20 to 5 mTorr. We have found that the surface anisotropy was closely correlated with the low-angle x-ray diffraction intensity. We believe that these results are mainly ascribed to the variation of microstructure in the Co/Pt multilayer thin films with sputtering Ar gas pressure.
This study was carried out to investigate the influence of light intensity on the growth of Korean white pine (Pinus koraiensis) seedlings. The seedlings were grown under four different relative light intensities: 100%, 63%, 37%, and 19% of full sunlight by covering with saran screen on seed bed. The results obtained were summarized as follows; 1. The highest shoot elongation was found at 37% in relative light intensity (RLI) plot, and the best growth in root, seedling length and diameter increment appeared at 100% on RLI plot. Contribution rates of shading to growth in shoot elongation, root growth, seedling length, and diameter increment were 9.3%, 26.2%, 21.0%, and 48.7%, respectively. 2. The greatest number of one-year-old needle fascicle was found at 100% in RLI plot, whereas that of two-year-old needle fascicle appeared at 37% in RLI plot. The contribution rate of the light intensity to number of needle fascicle was 3.9% and factor of leaf age contributed to number of needle fascicle in 27.8%. The length of needles grown under different light intensities varied with needle ages. The longest length of new needles appeared at 37% in RLI plot, but old needles were not clear in influence of light intensity. The contribution rate to needle length by the light intensity was 2.5%. 3. The heaviest value of the fresh and dry weight of seedlings appeared at 100% of RLI plot then decreased with light intensity. The contribution rates to fresh and dry weight by the shading were 38% and 7.6% respectively. 4. The largest value of the dry weight of needles appeared at 100% of RLI plot and then decreased with light intensity. The contribution rates to dry weight of needles by the light intensity was 13.18%. 5. The values of T/R ratio increased with decreased light intensity and the contribution rate was 7.0%. 6. Positive correlation and linear regressions were recognized between dry weight of leaf and other factors (dry weight of shoot, root, seedling and diameter increment).
Journal of the Society of Cosmetic Scientists of Korea
/
v.26
no.1
/
pp.261-274
/
2000
The o/w emulsions were prepared with saccharide surfactants which were sucrose monostearate(S160), sucrose distearate(S110), and POE(20) methyl glucose stearate(SSE20). And for emulsion the oils used were n-hydocarbon, squalane(SQ), liquid paraffin(LP), octylpalmitate(OP), octylstearate(OS), alkyl benzoate(AB), isostearyl benzoate(ISB). The structures of o/w emulsion droplet were investigated by laser light scattering and the fractal dimensions were calculated from light intensity curves. Increasing of concentration, chain length, and nonpolarity of oils, fractal dimensions of emulsion droplets were found greater. In general fiactal dimensions were varied from 1.7 to 2.8 and its structures were fractal But the fractal dimensions of octadecane( $C_{18}$), 50, and LP emulsified with S110 and S160 were varied from 3.0 to 3.2 and its structures were more dense. The overall fractal dimensions of S110 and S160 were varied from 2.1 to 2.6, that of SSE20 were varied from 1.5 to 2.1. So it was found that the structures of SSE20 system were less compact than that of S110 and S 160 system, because the hindrance effect of polyoxyehtylene group of SSE20 was stronger than that of sucrose of S160. The strucures of emulsion droplets changed according to the nature of emulsifiers and to compositions of oil substances which they contained, and the structures were found similar when the hydophilic moiety of emulsifiers was same.
TiO2 thin films with the substitution of oxygen with nitrogen were deposited on silicon substrate by metalorganic chemical vapor deposition (MOCVD) using Ti(OCH(CH3)2)4 (titanium tetraisopropoxide, TTIP) and N2O as source materials. X-ray diffraction (XRD) results indicated that the crystal structure of the deposited thin films was anatase TiO2 with only (101) plane observed at the deposition temperatures of 36$0^{\circ}C$ and 38$0^{\circ}C$, and with (101) and (200) plane at above 40$0^{\circ}C$. Raman spectroscopic results indicated that the crystal structure was anatase TiO2 in accordance with the XRD results without any rutile, fcc TiN, or hcp TiN structure. No fundamental difference was observed with temperature increase, but the peak intensity at 194.5 cm-1 increased with strong intensity at 143.0 cm-1 for all samples. The crystalline size of the films varied from 49.2 nm to 63.9 nm with increasing temperature as determined by slow-scan XRD experiments. The refractive index of the films increased from 2.40 to 2.55 as temperature increased. X-ray photoelectron spectroscopy (XPS) study showed only Ti 2s, Ti 2p, C 1s, O 1s and O 2s peaks at the surface of the film. The composition of the surface was estimated to be TiO1.98 from the quatitative analysis. In the bulk of the film Ti 2s, Ti 2p, O 1s, O 2s, N 1s and N 2s were detected, and Ti-N bonding was observed due to the substitution of oxygen with nitrogen. A satellite structure was observed in the Ti 2p due to the Ti-N bonding, and the composition of titanium nitride was determined to be about TiN1.0 from the position of the binding energy of Ti-N 2p3/2 and the quatitative analysis. The spectrum of Ti 2p energy level could be the sum of a 4, 5, or 6 Gaussian curve reconstruction, and the case of the sum of the 6 Gaussian curve reconstruction was physically most meaningful. From the results of Auger electron spectroscopy (AES), it was known that the composition was not varied significantly throughout the whole thickness of the film, and silicon oxide was not observed at the interface between the film and the substrate. The composition of the film was possible (TiO2)1-x.(TiN)x or TiO2-2xNx and in this experimental condition x was found to be about 0.21-0.16.
Kim J.S.;Lee S.H.;Park J.H.;Park H.W.;Choi J.C.;Park H.L.
Journal of the Korean Vacuum Society
/
v.15
no.4
/
pp.404-409
/
2006
Thin-film $ZnGa_2O_4 : Mn^{2+}$ phosphors of spinel structure were grown on quartz substrate by RF magnetron sputtering method at room temperature. As an increase of post-annealing temperatures, crystallinity, surface roughness and stoichiometry of thin films were varied. At the post-annealing temperatures of $500^{\circ}C$ and $600^{\circ}C$, the luminescence intensity was poor due to the poor crystallinity. The smallest surface roughness was observed at the sample post-annealed at $700^{\circ}C$ leading to low external extraction efficiency, and poor luminescence intensity. The highest luminescence intensity was shown at the sample post-annealed at $800^{\circ}C$. It was because both the surface roughness and crystallnity were optimized. On the other hand, at $900^{\circ}C$, the luminescence intensity was poor due to the violation of stoichiometry.
Purpose: This study (a) investigated the effect of microwave power intensity and sample thickness on microwave drying characteristics of radish strips, and (b) determined the best-fit drying model for describing experimental drying data, effective moisture diffusivity ($D_{eff}$), and activation energy ($E_a$) for all drying conditions. Methods: A domestic microwave oven was modified for microwave drying and equipped with a small fan installed on the left upper side for removing water vapor during the drying process. Radishes were cut into two fixed-size strip shapes (6 and 9 mm in thickness). For drying experiments, the applied microwave power intensities ranged from 180 to 630 W at intervals of 90 W. Six drying models were evaluated to delineate the experimental drying curves of both radish strip samples. The effective moisture diffusivity ($D_{eff}$) was determined from Fick's diffusion method, and the Arrhenius equation was applied to calculate the activation energy ($E_a$). Results: The drying time was profoundly decreased as the microwave power intensity was increased regardless of the thickness of the radish strips; however, the drying rate of thicker strips was faster than that of the thinner strips up to a certain moisture content of the strip samples. The majority of the applied drying models were suitable to describe the drying characteristics of the radish strips for all drying conditions. Among the drying models, based on the model indices, the best model was the Page model. The range of estimated $D_{eff}$ for both strip samples was from $2.907{\times}10^{-9}$ to $1.215{\times}10^{-8}m^2/s$. $E_a$ for the 6- and 9-mm strips was 3.537 and 3.179 W/g, respectively. Conclusions: The microwave drying characteristics varied depending on the microwave power intensity and the thickness of the strips. In order to produce high-quality dried radish strips, the microwave power intensity should be lower than 180 W.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.