• Progress in Superconductivity
• /
• 제3권1호
• /
• pp.31-35
• /
• 2001

We investigated the temperature and magnetic field dependent optical properties of a$ MgB_2$ thin film in the far-infrared region. In the superconducting state, i.e. 5 K, we obtained the values of superconducting gap $2\Delta$ ~ 5.2 meV and $2\Delta$ $_{k}$ $B/T_{c}$ ~1.8. Although the value of$ 2\Delta$$B/T_{c}$ was nearly half of the BCS value, the $2\Delta$ seemed to follow the temperature dependence of the BCS formula. Under the magnetic field (H), the superconducting state became suppressed. Interestingly, we found that the normal state area fraction abruptly increased at low field but slowly increased at high field. It did not follow the H-dependences predicted for a s-wave superconductor (i.e. a linear dependence) nor for a s-wave one (i.e. $H^{1}$2/ dependence). We discussed the complex gap nature of $MgB_2$ in comparison with two gap and anisotropic s-wave scenarios.ios.

• 대한치과보철학회지
• /
• 제33권2호
• /
• pp.335-353
• /
• 1995

The purpose of this study was to the determine the optimal torques values to tighten the retaining screw. 3-different implant system tested were as follows : Branemark implant system$(3.75mmD{\times}100mm)$, Steri-Oss implant system$(3.8mmD{\times}10mm)$. One fixtures of each implant system was mounted into the epoxy resin block and abutment/superstructure complex was constructed. Eighty dental college students(male : 40, female : 40) of Chosun University were selected and were asked to tighten the retaining screws. Abutment/superstructure complex of each implant system was tightened to the maximum torque by use of hand-held screw driver, and then torque value was measured with torque value was measured with torque driver(Tohnichi torque driver, model 20 FTD, Tohnichi MFG, Co., LTD., Tokyo, Japan). Abutment/superstructure complex of each implant system was titghtened to each torque of 10 N-cm, 20 N-cm and 30 N-cm, and then the dynamic load(vertical & diagonal load) was applied to the abutment / superstructure complex. The gap between abutment/superstrure in each implant system was measured with 3-dimensional measuring microscope(model No. 850, Germany). The results were as follow : 1. Torque values according to the individual subjects showed wide range. 2. Torque values according to sex showed statistical significant difference. Those are as follows : in case of male, $9.38{\pm}2.93$ N-cm ; incase of female, $7.80{\pm}2.25$ N-cm. 3. Torque values according t implant systems showed statistical significant difference. Those are as follows : in ase of Branemark implant system, $6.54{\pm}1.54$ N-cm : in ase of Steri-Oss implant system, $10.1{\pm}2.88$ N-cm ; in case of IMZ implant system, $9.18{\pm}2.17$ N-cm. 4. The more torque value of tightening screw was increased, the less the gap was after the vertical and diagonal loading. 5. The gap after the diagonal loading was greater than that after the vertical loading. 6. The magnitude of gap between abutment/superstructure in order of IMZ, Steri-Oss, Branemark implant system after the verical and diagonal loading. 7. The gap under the diagonal loading after applying 30 N-cm torque showed no statistical significant difference in cases of the Branemark system and the Steri-Oss implant system but it showed significant different in case of the IMZ implant system.

• 수산해양기술연구
• /
• 제33권3호
• /
• pp.173-182
• /
• 1997

선망어법의 어회과정에 있어서 어군행동에 관한 기초적인 연구를 목적으로 제주 근해에서 사용하고 있는 고등어 선망어구인 파워불록용 선망(Powetblock seine)과 앞으로 예상되는 단선조작에서의고등어 선망어구인 트리플레스용 선망(Triplex seine)의 두 가지 모형망을 1/180로 제작 하고 선망에 의해 포위된 어군의 망내행동과 양쪽 선단의 개구부를 통하여 도피하는 어군의 행동을 관찰 분석함과 동시에 망단의 개구부의 면적 및 장력변화 등을 해석하였으며, 그 결과는 다음과 같다. 1. 죔줄죄기 소요시간 20분일 때, 개구부로 도피하는 아군의 평균 유영속도는 Powerblcok seine에서 9.71cm/sec, Triplex seine에서 9.97cm/sec였다. 2.죔줄죄기 소요시간 20분중 좀줄을 50% 정도 감아들었을 때, 선망내의 어군은 Powerblock seine의 경우 I section 10%, II section방향으로 10% 유영하는 행동을 보였다. 3.죔줄죄기 소요시간 20분중 10분 경과했을 때, 전면 망단 개구부의 면적 감소율은 Powerblock seine이 63.5%, Triplex seine이 어군도피에 대한 수평적 서단능력이 높았따. 그리고, 좀줄에 걸리는 최대장력은 Powerblock seine이 약 8.1톤, Triplex seine이 8.3톤으로 나타 났는데, 양자의 차이는 그다지 크지 않았다.

• 한국가스학회지
• /
• 제2권2호
• /
• pp.55-60
• /
• 1998

열경화성 수지의 충전제로 많이 사용되고 있는 소나무 분진을 시료로 분진폭발의 최소착화에너지와 폭발한계를 측정하여 분진폭발 특성을 고찰하였다. 실험은 전극간 거리, 분진운 농도, 분진입도 및 수분 등에 대한 실험을 행하였다. 그 결과 전극간 거리가 4mm 이하로 되면 증가하는 경향을 나타내었으며, 2mm 이하에서는 착화에너지가 갑자기 무한대로 되어 이 값이 한계전극 거리임을 알았다. 또한 분진운 농도가 증가하고 분진 입도가 미세할수록 폭발성이 용이하였으며, 동일한 입도의 분진에서 수분 함유량이 증가할수록 최소착화에너지가 증가하였다.

• Journal of Electrical Engineering and Technology
• /
• 제1권3호
• /
• pp.338-342
• /
• 2006

This paper analyzed the power loss of transformers considering the magnetic component. For this, each winding strategy and the effect of air gap between the ferrite core have been an important variable for optimal parameter calculation. Inductors are very well known design rules to devise, but the performance of the flyback converter as a function of transformer winding strategy has not been fully developed. The transformer analysis tool used was PExpert. The influence of the insulator thickness, effect of the air gap, how the window height and variation of the capacitive value effects the coil and insulator materials are some of parameters that have been analyzed in this work. The parameter analysis is calculated to a high frequency of 48[kHz]. Therefore, the final goal of this paper was to calculate and adjust the parameters according to the method of winding array and air gap minimizing the power loss.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(3)
• /
• pp.157-160
• /
• 2001

This paper has been studied a Adaptive Mutation rate Genetic Algorithm Processor. Genetic Algorithm(GA) has some control parameters such as the probability of bit mutation or the probability of crossover. These value give a priori by the designer There exists a wide variety of values for for control parameters and it is difficult to find the best choice of these values in order to optimize the behavior of a particular GA. We proposed a Adaptive mutation rate GA within a steady-state genetic algorithm in order to provide a self-adapting mutation mechanism. In this paper, the proposed a adaptive mutation rate GAP is implemented on the FPGA board with a APEX EP20K600EBC652-3 devices. The proposed a adaptive mutation rate GAP increased the speed of finding optimal solution by about 10%, and increased probability of finding the optimal solution more than the conventional GAP

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.181-183
• /
• 1996

A novel model of an inductive superconducting fault current limiter with an inductive superconducting fault current limiter with the air-gap core was fabricated and tested. If its impedance is not high enough to limit the fault current, then destructive damage occurs in the power system. We attained a magnetic saturation under higher current by an effective air gap introduced in the core. The fault current was successfully limited to two times as much as the nominal current at a 60 Hz source having an effective voltage of 70 V. The fault current flowing under such conditions can be limited to a desired value without any fault current peak within 1/4 cycles.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.913-915
• /
• 1998

This paper describes the application of two and three dimensional electric field analysis for vacuum interrupter with spiral contacts. The electric potentials of floating arc shield and electric fields in a vacuum interrupter are analysed at various gap distances from 1mm to 12mm. The electric potentials of floating shield is increased with the gap distance, which is because the relative position of shield is closer to the fixed contact so that the capacitance distribution inside interrupter is varied. The calculated results show that the maximum value of electric field in a vacuum interrupter with floating shield is nearly same to that without shield at short gap distance below 5mm, however at longer gaps more intensive electric field is achieved in interrupter with shield comparing with the model without shield, which is due to the influence of charged floating shield.

• 한국화재소방학회논문지
• /
• 제10권1호
• /
• pp.3-9
• /
• 1996

Electrostatic charge is generated in large scale or high speed processes dealing with materials with large resistance, or under complicated condition. Fire and explosion often occur due to electrostatic charge accumulated in flammable gases, vapor, liquids and powder. It is usually very difficult to verify the cause of accidents as well as the prevention. In this study, it is shown that the needle electrode needs the electrode gap from 1.8mm to 3.8mm, sphere electrode and plate electrodes need the electrode gap of 1.9mmfor the minimum ignition energy. The sphere electrode and the plate electrode requires 12.8mJ and 3.2mJ of minimum ignition energy respectively with the electrode gap of 1.1mm. The ignition voltage rises to very large value as the ground resistance increases.

• 한국결정성장학회지
• /
• 제14권1호
• /
• pp.17-20
• /
• 2004

본 논문의 목적은 초전도체에 자기장 H가 인가되고 있는 경우. 임계온도에서의 비열 불연속폭을 열역학적 방법을 사용하여 인가자기장 H의 해석적 함수로서 정확히 구하는 데에 있다. 그리고 이러한 결과를 이용하여 몇몇 초전도체의 비열 불연속폭에 대한 수치를 계산하고 그 의미를 분석할 것이다 .특히 초전도체의 일반적 현상인 상태변이 시의 비열불연속 현상이 특정 세기의 자기장하에서는 일어나지 않는다는 주목할 만한 결과에 대해서도 언급할 것이다.