• 한국주조공학회지
• /
• 제43권3호
• /
• pp.107-136
• /
• 2023

주강품 사형주조에는 천연규사가 보편적으로 사용되었고, 규사의 열적특성 부족에 의한 소착결함 억제를 위해, 크로마이트사가 사용되기도 하였으나, 반복 사용에 의한 골재 열화, 시스템샌드 혼입 문제, 분리 제거의 어려움, 높은 밀도에 따른 조형 시 하중증가, 크롬 함유 폐기물이 되는 단점이 있다. 최근에는 주조업계의 중요한 과제로써 산업폐기물 저감 및 대기환경 개선이 부각되고 있다. 종래의 주물사 사용 시 발생되는 문제점 해결과 주조공장의 환경개선을 위해서, 천연사를 대체 적용할 수 있는 다양한 인공사가 개발되어 소개되고 있다. 인공사는 용융분사법으로 제조된 인공사와 조립소결법으로 제조된 인공사 및 분쇄법으로 제조된 인공사로 분류할 수 있으며, 원료광물의 종류, 제조공법에 따라 상이한 물리적 특성을 나타낸다. 본 연구에서는 각종 주물사의 물성, 주형강도, 물리적 내구성, 열적 내구성, 소착시험편 주조 등의 비교 평가시험을 하였다. 밀도에 따른 주물사 실사용량, 주물사 형상에 따른 주형강도, 주물사의 물리적 및 열적 내구성, 주물사의 내열특성을 종합적으로 고려하였을 때, 아크용사법으로 제조된 용융인공사 A1 또는 분말식화염용사법으로 제조된 용융인공사 B가 대형주강품 주조에 가장 적합한 구형의 인공사로 판단된다.

• 산업경영시스템학회지
• /
• 제4권5호
• /
• pp.1-10
• /
• 1981

The purpose of this study is to cut down cost of production and improve the productivity of industry through quality improvement of castings and reduction of defectives by applying the experimental design to the foundry sand mixing operation done at molding department in the foundry. Among the related foundry sand mixing factors which have an effect on casting the experiment of which factors have a dominant effect on quality improvement was performed between two different levels by means of "$2^n$ type orthogonal array." The results cail be summarized as follows ; (1) The optimum conditions per each foundry sand mixing between two different levels proved to be such as $A_2$(used sand) : 24 unit (172.8kg), $B_2$(unused sand ) : 2 unit (15.0kg), $C_2$(binder) : 2.5 unit (4.4kg). $D_2$(addition agent) : 1 unit(1.4kg) and $F_1$(moisture) : 7.4%(14.6kg). (2) As a result of the application of experimental design, the fraction defective during the foundry sand mixing operation turned out to be reduced front 6.6% to 2.04%. (3) For the purpose of cost-down, It was found that the optimum level decision of foundry sand mixing for various castings is required to be made by means of experimental design.al design.

• 자원리싸이클링
• /
• 제5권1호
• /
• pp.9-13
• /
• 1996

Once-used $CO_2$-silicate bonded sand from domestic foundry is mostly discarded in a reclaimed land because of its bad collapsibility and reproduction properties. So this causes serious environmental problem. We can get 82% recovery of silica from used sand by scrubbing reclamation process in this research. When we repeat the reclamation-recycling of the foundry sand, artificial silica sand is broken down below 2-cycles, but natural silica sand does not destroyed when used repeatedly more than 10-cycles and have a good property of recycling with little change of its size.

• 산업기술연구
• /
• 제22권A호
• /
• pp.119-125
• /
• 2002

In Kwangjin industrial company, mill is operating for the foundry sand production at the rate of 25t/hr from quartzite. Foundry sands fall into four distinct categories: silica sand, lake sand, bank sand, and natural molding sand. Silica sand is a general term used to describe crushed, washed, graded, dried, and cooled clay-free sands. This study was conducted for the investigation of the foundry sand productivity and the life span of the hammer according to the material quality. The life time of hammer from several manufacturer were compared in order to find out the grinding efficiency of the various hammer material. In the result of tests, the life time of high-Mn hammer was 10.5 hours while that of high-Cr was 19.5 hours. The life time in case of typical worn shape hammers was about 12 hours and the average time of a blowhole hammer was about 6.5 hours.

• 한국방재학회 논문집
• /
• 제8권2호
• /
• pp.105-110
• /
• 2008

Flowable fill is generally a mixture of sand, fly ash, a small amount of cement and water. Sand is the major component of most flowable fill with waste materials. Various materials, including two waste foundry sands(WFS), an anti-corrosive waste foundry sand and natural soil, were used as a fine aggregate in this study. Natural sea sand was used for comparison. The flow behavior, hardening characteristics, and ultimate strength behavior of flowable fill were investigated. The unconfined compression test necessary to sustain walkability as the fresh flowable fill hardens was determined and the strength at 28-days appeared to correlate well with the water-to-cement ratio. The strength parameters, like cohesion and internal friction angle, were determined for the samples prepared by different curing times. The creep test for settlement potential was conducted. The data presented show that by-product foundry sand, an anti-corrosive WFS, and natural soil can be successfully used in controlled low strength materials(CLSM), and it provides similar or better properties to that of CLSM containing natural sea sand.

• 콘크리트학회논문집
• /
• 제17권1호
• /
• pp.141-147
• /
• 2005

The development of automobile, vessel, rail road, and machine industry leads an increase of foundry production used as their components, which cause a by-product, waste foundry sand (WFS). The amount of the WFS produced in Korea is over 700,000 tons a year, but most WFS has been buried itself and only $5{\~}6\%$ WFS is recycled as construction materials. Therefore, it is necessary for most WFS to research other ways which can be used in a higher value added product. The study on recycling it as a fine aggregate for concrete or green sand has been in progress in America and Japan since 1970s and 1980s respaectively. In this study, two types of WFS were used as a fine aggregate for concrete. Nine types of concrete aimed at the specified strength of 30 MPa were mixed with washed seashore coarse sand in which salt was removed, and WFS and then appropriate mixture proportion of concrete was determined. Moreover, basic properties such as air contents, setting time, bleeding, workability and slump loss of the fresh concrete with WFS were tested and compared with those of the concrete mixed without WFS. In addition, both compressive strength of hardened concrete at each ages and tensile strength of it at the age of 28 days were measured and discussed.

• Computers and Concrete
• /
• 제19권6호
• /
• pp.617-623
• /
• 2017

This work is conducted with the aim of using waste material to reserve the natural resources. The objective is accomplished by conducting experimentation and verify by modeling based on fuzzy logic. In experimentation, concrete is casted by using natural/river sand as fine aggregate and termed as control specimen. Natural sand is conserved by replacing it with used foundry sand (UFS) by an amount of 10, 20 and 30% by weight. Fresh and hardened properties of concrete are investigated at different ages. It is observed that compressive strength and modulus of elasticity reduced with the increase in amount of UFS. Furthermore, concrete compressive strength is predicted by using fuzzy logic model and verified at different replacement ratio and age with experimental observations.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.489-496
• /
• 1999

The objective of this study is to present engineering properties required in use of co-mixtures of fly ash and WFS(Waste Foundry Sand)'s, which are Presently used as fill or (lovable backfill. The fly ash, generated at the Tae-An thermoelectric power plant was used in this research and was classified as Class F. Green Sand, Furane Sand, and Coated Sand, which had been used at a foundry located in Pusan, were used. Laboratory experiments were peformed to obtain the physical properties of the co-mixture of fly ash and WFS. The range of permeability for all the co-mixtures was from 3.0×10/sup -3/㎝/s to 6.0×10/sup -5/㎝/s. The unconfined strength of the 7-day cured specimens composed of Green Sand reached 94% of that of 28-day cured specimens but for the 7-day cured specimens composed of, respectively, Furnace Sand and Coated Sand, only 64% and 66% of the strength of the 28-day cured specimens were reached. Results of the consolidated-untrained triaxial test showed that the specimens composed of Furnace Sand showed a distinct increase of the internal friction angle, while the other specimens showed negligible increase. In the case of 28-day cured specimens, specimens composed of Furnace Sand showed an internal friction angle of 41.8°, while specimens of Green and Coated Sand showed those of 33.5° and 35.0°, respectively. From the shrinkage test, the shrinkage ratios of all specimens did not exceed 0.25%.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.281-286
• /
• 2001

The development of automobile, vessel, rail road, and machine industry leads increase of foundry production used as their components, which cause a by-product, waste foundry sand (WFS). The amount of the WFS produced in Korea is over 900,000 ton a year, but most WFS buries itself and only 5~6% WFS is recycled as a material in construction materials. In this study, WFS is used as a fine aggregate for concrete. Five types of concretes aimed at the specified strength of 240$\pm$10 kgf/$cm^{2}$ , air contents of 4.5$\pm$1% and slump of 12$\pm$1.5cm were mixed with washed coarse seashore sand(WFS) in which salt was removed and then optimum mix proportion of concrete was determined. Moreover, basic properties such as setting time, workability, bleeding and slump loss of the fresh concrete with WFS were tested and compared with those of the concrete mixed without WFS. In .addition, both compressive strength of hardened concrete at each ages and tensile strength of it at the age of 28 days were measured and discussed.

• 한국도로학회논문집
• /
• 제3권4호
• /
• pp.105-116
• /
• 2001

본 연구는 주물고사를 이용한 아스팔트 콘크리트와 주물고사의 물리적 화학적 특성을 비교 분석하는 것이다. 주물고사의 아스팔트 콘크리트 적용성을 평가하기 위하여 XRF, SEM, 제타전위를 측정하여 주물고사의 물리 화학적 특성을 알아보았다. 주물고사 아스팔트 콘크리트의 박리저항성을 향상시키기 위하여 박리방지제(소석회(Hydrated lime), 액상박리방지제)를 사용하였다. 그리고 주물고사 아스팔트 콘크리트 혼합물의 인장특성과 내구성 향상을 위하여 LDPE를 사용하였다. 또한 주물고사 아스팔트 콘크리트의 공용성을 알아보기 위하여 간접인장강도, 수분취약성시험, 동결 융해시험, 반복주행시험을 수행하였다. 시험결과 주물고사 아스팔트 콘크리트의 역학적 특성이 일반 아스팔트 콘크리트에 비해 같거나 향상되는 것으로 나타났다. 따라서 주물고사를 아스팔트 콘크리트에 재활용할 수 있다는 결론을 얻었다.