• Information Systems Review
• /
• v.4 no.2
• /
• pp.237-255
• /
• 2002

In this study, we develop a four phase model of ERP implementation, which includes Chartering phase, Project phase, Shakedown phase, and Onward and upward phase. We then examine how the completeness of each phase influences the implementation success as well as the completeness of next phase. The results of this study show that project phase and onward and upward phase both have significant impacts on the implementation success. We also find that all relationships between the completeness of previous phase and next phase are significantly positive.

• Solar Energy
• /
• v.18 no.3
• /
• pp.95-105
• /
• 1998

In this study, basic design data which were required for development of highly efficient ice storage system with low temperature latent heat were experimentally obtained. The ice storage system considered in this study was the one that has been widly used in the developed country and called the ice-on-coil type. Using the system, the ice storage performance for various design parameters which were the flow direction and the inlet temperature of the secondary fluid was tested. In addition, the timewise variation of the interface profiles between the solid and the liquid were visualized, and the heat transfer characteristics of the Phase Change Material(PCM) in the ice storage tank were Investigated. During the freezing processes in the ice storage tank with several vertical tubes, decrease of the heat transfer area and the heat resistance of the ice layer made the increasing rate of ice packing factor(IPF) less. The total freezing energy for the upward flow of the secondary fluid was higher than that for the downward flow. The average ice storage efficiency for the upward flow of the secondary fluid was higher than that for the downward flow.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.3
• /
• pp.371-380
• /
• 2015

Particulate matters in a water distribution system are main causes of turbidity and discoloration of tap water. They could be removed by conventional or uni-directional flushing in a water distribution system. The behaviors and required flow velocity of particles are not well known for their flushing. A model water main and hydrant were made from transparent acrylic pipe of 30mm and 16mm in diameter, respectively. We analyzed the effect of flushing velocity, particle density, and particle diameter. We found that the existence of break-though velocities at which particles begin to be removed, and which are affected by their physical properties. The removal efficiencies seemed to be influenced by resuspension capabilities related to their upward movement from the bottom. Heavy particles like scale were hard to remove through upflow hydrant because the falling velocity, calculated using Stokes' law, was higher. Particle removal efficiencies of upward hydrant and downward drain showed minor differences. Additionally, the length between hydrant and control valve affected flushing efficiency because the particulate matters were trapped in this space by inertia and recirculating flow.

• Atmosphere
• /
• v.19 no.4
• /
• pp.319-329
• /
• 2009

The intensive dust observation experiment has been performed at Korea Global Atmosphere Watch Center (KGAW) in Anmyeon, Korea during each spring season from 2007 to 2009. Downward and upward hyper-spectral spectrums over the dust condition were measured to understand the hyper-spectral properties of Asian dust using both ground-based Fourier Transform Infrared Spectroscopy (FT-IR) and space-borne AIRS/Aqua. To understand the impact of the Asian dust, a Line-by-Line radiative transfer model runs to calculate the high resolution infrared spectrum over the wave number range of $500-500cm^{-1}$. Furthermore, the radiosonde, a $PM_{10}$ Sampler, a Micro Pulse Lidar (MPL), and an Aerodynamic Particle Sizer (APS) are used to understand the vertical profile of temperature and humidity and the properties of Asian dust like concentration, altitude of dust layer, and size distribution. In this study, we found the Asian dust distributed from surface up to 3-4 km and volume concentration is increased at the size range between 2 and $8{\mu}m$ The observed dust spectrums are larger than the calculated clear sky spectrums by 15~60K for downward and lower by around 2~6K for upward in the wave number range of $800-1200cm^{-1}$. For the characteristics of the spectrum during the Asian dust, the downward spectrum is revealed a positive slope for $800-1000cm^{-1}$ region and negative slope over $1100-1200cm^{-1}$ region. In the upward spectrum, slopes are opposed to the downward one. It is inferred that the difference between measured and calculated spectrum is mostly due to the contribution of emission and/or absorption of the dust particles by the aerosol amount, size distribution, altitude, and composition.

• The Journal of Korea Robotics Society
• /
• v.9 no.3
• /
• pp.170-177
• /
• 2014

This paper proposes a novel upward-looking camera-based global localization using a ceiling image map. The ceiling images obtained through the SLAM process are integrated into the ceiling image map using a particle filter. Global localization is performed by matching the ceiling image map with the current ceiling image using SURF keypoint correspondences. The robot pose is then estimated by the coordinate transformation from the ceiling image map to the global coordinate system. A series of experiments show that the proposed method is robust in real environments.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.5
• /
• pp.395-403
• /
• 1991

The purpose of this investigation was to characterize nucleate boiling and burn-out heat flux for rectangular free jet with saturated water impinging perpendicularly and upward against a flat uniform heat flux surface. Heat flux measured for Reynolds number based on rectangular nozzle width and for aspect ratio. The result of nucleate boiling heat transfer was presented nondimensional experimental equation including Nusselt, Boiling, Subcooling, Reynolds and Weber number. The effect of aspect ratio of heated surface in the burn-out heat flux had not appeared distinctly. But for the same aspect ratio, burn-out heat flux increased linearly with increment of nozzle exit velocity.

• Proceedings of the KSRS Conference
• /
• 1998.09a
• /
• pp.89-94
• /
• 1998

Seasonal variation of attenuation coefficient spectra in Japan sea was extracted from underwater radiance/irradiance spectra observed by a moored buoy system developed by National Space Development Agency of Japan (NASDA). The buoy was deployed 9 months from August 31, 1996 to June 1, 1997. Throughout this period, it was collecting downward irradiance and upward radiance spectra under water at the depth of 1.5m and 6.5m everyday. The dairy averaged diffused attenuation coefficient spectra and underwater reflectance spectra were calculated. The results were compared with the absorption spectra of filtered samples obtained by validation cruises, which carried out 5 times during the moored period. Also, the natural fluorescence of chlorophyll a were extracted from the upward radiance spectra observed at 1.5m depth. The seasonal variation of the calculated attenuation coefficient spectra and the natural fluorescence were examined. The result shows a weak blooming of phytoplankton on November and a large blooming on April.

• MALSORI
• /
• no.35_36
• /
• pp.49-61
• /
• 1998

The study on the intonational characteristics is concentrated on the lowering of the pitch level that is described as declination and downstep. The Taegu dialect, which has phonological accentual system, has these phonetic characteristics in affirmative sentences or Yes-No Question sentences. But there is the opposite phenomenon in WH question sentences in Taegu dialect. When the accent of interrogative word in the sentence intial position is LHL, intonation pattern shows a continuous upward movement, indicating that intonation pattern of Taegu dialect is influenced by not only grammatical system but also accentual system.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.5 no.5
• /
• pp.449-458
• /
• 2010

Recently, the interest on object oriented design patterns has been increased considering to reusability of software and efficiency of maintenance expense in designing software architecture. In this paper, we design the paper submission management system applicable to specific domain using domain object interface based on object oriented design patterns, and then implement it with Java and XML. The proposed system applies method of implementation by assemblying each system objects with upward after system entire architecture design by combining properly downward method and upward method and applies with GoF Design pattern. As well as, we convert domain data of system into the form of various persistent objects through XML, and minimize the complexity of system by not adopting method that generates domain object as in Class with automatic. Finally, the implementation of our system can be used in general C/S environment, but we implement system user GUI using the XSLT built in general web browser in consideration for user convenience and consistency.

• Journal of Welding and Joining
• /
• v.26 no.5
• /
• pp.66-73
• /
• 2008

Welding work in pre-erection or erection stage of shipbuilding construction to be carried out in flat and vertical upward position mostly and Electrogas welding(EGW) is actively applied especially for vertical butt joint of thicker steel plate recently. In this study considered how to develope and improve mechanical properties of weld metal and HAZ in high heat input welding processes such as EGW and Electroslag welding(ESW) with its welding equipment in order to extend the application range to the longitudinal members and hatch coaming parts of container ship. Some components of welding system and parameters were modified to get the faster travel speed and reduce weld heat input, and also by adding additional filler rods or tubes increase the amount of deposited weld metal. With the test get some good date can apply to actual fabrication work and recommend items to manufacture welding materials make better. Above all things it's a fruition that to prepare the possibility of application of ESW to shipbuilding construction which fill up the gap of stoppage days of more than 20 years.