• Interaction and multiscale mechanics
• /
• 제4권4호
• /
• pp.291-311
• /
• 2011

To simulate the self excited torsional vibrations of rotating drill strings (DSs) in vertical bore-holes, the nonlinear wave models of homogeneous and sectional torsional pendulums are formulated. The stated problem is shown to be of singularly perturbed type because the coefficient appearing before the second derivative of the constitutive nonlinear differential equation is small. The diapasons ${\omega}_b\leq{\omega}\leq{\omega}_l$ of angular velocity ${\omega}$ of the DS rotation are found, where the torsional auto-oscillations (of limit cycles) of the DS bit are generated. The variation of the limit cycle states, i.e. birth (${\omega}={\omega}_b$), evolution (${\omega}_b<{\omega}<{\omega}_l$) and loss (${\omega}={\omega}_l$), with the increase in angular velocity ${\omega}$ is analyzed. It is observed that firstly, at birth state of bifurcation of the limit cycle, the auto-oscillation generated proceeds in the regime of fast and slow motions (multiscale motion) with very small amplitude and it has a relaxation mode with nearly discontinuous angular velocities of elastic twisting. The vibration amplitude increases as ${\omega}$ increases, and then it decreases as ${\omega}$ approaches ${\omega}_l$. Sectional drill strings are also considered, and the conditions of the solution at the point of the upper and lower section joints are deduced. Besides, the peculiarities of the auto-oscillations of the sectional DSs are discussed.

• Computers and Concrete
• /
• 제6권5호
• /
• pp.357-376
• /
• 2009

In the design of concrete columns, it is important to provide some nominal flexural ductility even for structures not subjected to earthquake attack. Currently, the nominal flexural ductility is provided by imposing empirical deemed-to-satisfy rules, which limit the minimum size and maximum spacing of the confining reinforcement. However, these existing empirical rules have the major shortcoming that the actual level of flexural ductility provided is not consistent, being generally lower at higher concrete strength or higher axial load level. Hence, for high-strength concrete columns subjected to high axial loads, these existing rules are unsafe. Herein, the combined effects of concrete strength, axial load level, confining pressure and longitudinal steel ratio on the flexural ductility are evaluated using nonlinear moment-curvature analysis. Based on the numerical results, a new design method that provides a consistent level of nominal flexural ductility by imposing an upper limit to the axial load level or a lower limit to the confining pressure is developed. Lastly, two formulas and one design chart for direct evaluation of the maximum axial load level and minimum confining pressure are produced.

• Journal of Welding and Joining
• /
• 제8권2호
• /
• pp.40-52
• /
• 1990

Fatigue behavior of the AH, DH and EH grade TMCP(Thermo-Mechanical Control Process) steels was studied. High cycle and low cycle fatigue tests were carried out for the weldment and base metal of each steel. The results showed that the fatigue limit at 2 * $10^6$ cycles was 33 to 37 kg/$mm^2$ for the base metal and 30 to 34 kg/$mm^2$ for the weldment. The ratio of fatigue limit to tensile strength for TMCP steels was 0.65 to 0.71, which was a value close to the upper limit for the ordinary steels. It was also found that the high cycle fatigue behavior of TMCP steels could be affected by the microstructures of base metal. It will be necessary to have fine structure for TMCP steels to increase the fatigue resistance. In low cycle fatigue test, the fatigue lifetime of AH and DH steels accorded well with the ASME best fit curve, while that of EH steel was considerably lower than the fatigue lifetime of the other steels. Fatigue resistance of the weldment made by high heat input(180kJ/cm) welding was not lower than that made by low heat input(80kJ/cm) welding in case of high cycle fatigue, but the high heat input welding decreased the fatigue resistance in case of low cycle fatigue.

• 한국대기환경학회지
• /
• 제34권1호
• /
• pp.144-155
• /
• 2018

As the public interest in environmental issues increased, the "Act On The Integrated Control Of Pollutant-Discharging Facility" was enacted. Through the integrated environmental pollution prevention act in which 19 industries with large environmental impacts are sequentially applied, pollutants can be managed in a medium-integrated manner and integrated permission of the business unit is possible and BAT can be applied to enable a scientific and proactive environmental management system. In addition, if the facility with BAT works normally, the pollutant emission is offered with the range of lower limit to upper limit. This study analyzed the overview of Best Available Techniques-Associated Emission Levels (BAT-AEL), and its setting procedure and method, and then suggested the BAT-AEL of a waste incineration facility. In comparative analysis on Emission Limit Values (ELVs) of EU, this study tries to propose improvement matters and development directions if the relevant standard is revised.

• 한국화재소방학회논문지
• /
• 제27권3호
• /
• pp.47-51
• /
• 2013

폭발한계는 가연성물질의 화재 및 폭발위험성을 결정하는데 주요한 특성치 가운데 하나이다. 많은 유기산류는 연소열과 폭발한계, 화학양론계수와 폭발한계가 상관관계가 있음을 보여주고 있다. 본 연구에서, 유기산류의 폭발하한계와 상한계에 대해 연소열과 화학양론계수를 이용하여 예측하였다. 제시된 예측식에 의한 예측값은 문헌값과 적은 오차범위에서 일치하였다. 제시된 방법론을 사용하여 다른 유기산류의 폭발한계 예측이 가능해졌다.

• 토지주택연구
• /
• 제11권2호
• /
• pp.87-94
• /
• 2020

Offshore renewable energy resources are attractive alternatives in addressing the nation's clean energy policies because of the high demand for electricity in the coastal region. As a large portion of potential resources is in deep and farther water, economically competitive floating systems have been developed. Despite the advancement of floating technologies, the high capital cost remains a primary barrier to go ahead offshore renewable energy projects. The dynamically installed piles (DIPs) have been considered one of the most economical pile concepts due to their simple installation method, resulting in cost and time-saving. Nevertheless, applications to real fields are limited because of uncertainties and underestimated load capacity. Thus, this study suggests the appropriate analytical approach to estimate the inclined load capacity of the DIPs by using the upper bound plastic limit analysis (PLA) method. The validity of the PLA under several conditions is demonstrated through comparison to the finite element (FE) method. The PLA was performed to understand how flukes, soil profiles, and load inclinations can affect the inclined load capacity and to provide reliable evaluations of the total resistance of the DIPs. The studies show that PLA can be a useful framework for evaluating the inclined load capacity of the DIPs under undrained conditions.

• 한국화재소방학회논문지
• /
• 제23권5호
• /
• pp.50-56
• /
• 2009

폭발한계와 최소자연발화온도는 가연성 물질의 화재 및 폭발 위험성을 결정하는데 중요한 특성으로 이용된다. 에틸렌의 안전한 취급을 위해 에틸렌의 폭발한계와 최소자연발화온도를 고찰하였다. 에틸렌의 폭발하한계와 상한계는 공기 중에서 각 각 2.6vol%와 36vol%를 추천하며, 최소자연발화온도는 전면 가열인 경우는 $420^{\circ}C$, 국소 고온표면인 경우는 약 $800^{\circ}C$를 추천한다. 또한 에틸렌의 폭발한계의 온도 및 압력의 존성에 대한 새로운 예측식을 제시하였으며, 제시된 식에 의한 예측값은 문헌값과 일치하였다.

• 한국가스학회지
• /
• 제19권2호
• /
• pp.5-11
• /
• 2015

폭발한계는 가연성물질의 화재 및 폭발위험성을 결정하는데 주요한 특성치 가운데 하나이다. 많은 알데히드류는 연소열과 폭발한계, 화학양론계수와 폭발한계가 상관관계가 있음을 보여주고 있다. 본 연구에서, 알데히드류의 폭발하한계와 상한계에 대해 연소열과 화학양론계수를 이용하여 예측하였다. 제시된 예측식에 의한 예측값은 문헌값과 적은 오차범위에서 일치하였다. 제시된 방법론을 사용하여 다른 알데히드류의 폭발한계 예측이 가능해졌다.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1097-1103
• /
• 1988

본 연구에서는 이 좁은 벤트내에 자료가 모이는 피로균열의 특성을 이용하여 표면피로균열의 성장거동을 파괴역학적으로 해석, 연구하여 균열의 성장특성과 $S-N_{f}$ 곡선의 추정을 마이크로 컴퓨터로 계산하였다.

• Nuclear Engineering and Technology
• /
• 제53권6호
• /
• pp.1931-1938
• /
• 2021

Uranium ingot is produced by metallothermic reduction of uranium tetrafluoride using magnesium or calcium as reductant. Presence of oxygen containing compounds viz. uranyl fluoride and uranium oxide in the starting uranium fluoride has a significant effect on the firing time, final temperature of the charge, slag-metal separation and hence the metal recovery. As reported in the literature, the maximum tolerable limit for uranyl fluoride in the UF₄ is 2.5 wt% and limit for uranium oxide content is in the range 2-3 wt%. No theoretical or experimental basis is available till date for these limits. Analyses have been carried out in this study to understand the effect of UO₂F₂ concentration in the starting fluoride on the final temperature of the products and thus the reduction characteristics. UF₄ having uranyl fluoride concentration, less than as well as more than 2.5 wt%, have been investigated. Thermodynamic calculations have been carried out to arrive at a general expression for the final temperature attained by the products during calciothermic reduction of UF₄. Finally, an upper limit for the oxygen containing impurities has been estimated using the CaO-CaF₂ phase diagram.