• 소성∙가공
• /
• 제29권6호
• /
• pp.316-322
• /
• 2020

The flow stress curve is usually determined via uniaxial tensile or simple compression test. However, the flow stress curve up to high strain cannot be obtained using these two tests. This study presents a simple method for obtaining the flow stress curve up to high strain via FE analysis, a simple compression test, and an indentation test. In order to draw the flow stress curve up to high strain, the indentation test was carried out with the pre-stained specimen using the simple compression test. The flow stress curve of Al6110 was evaluated up to high strain using the proposed method, and the result was compared with the flow stress curve of the uniaxial tensile test of the initial material.

• 에너지공학
• /
• 제14권4호
• /
• pp.241-247
• /
• 2005

3열 정렬형 관군 배열에서 3열의 'common flow up'과 'common flow down' 형상의 와류발생기를 부착하여 와류발생기에 의한 열전달 촉진과 압력강하를 비교하였다 선행 연구자들이 제안한 'common flow down' 형상의 와류발생기는 와류발생기가 없는 휜-관군에 비해 열전달 촉진은 $10\%{\~}25\%$ 향상되었고, 압력강하는 $20\%{\~}35\%$ 증가하였다. 'common flow up' 형상의 와류발생기의 경우 후연 수평거리(${\Delta}y$)를 변화시키면서 평가하였다. 와류발생기는 삼각형과 사각형 형상을 적용하였다. 후연 수평거리(${\Delta}y$)가 5mm이고 삼각형의 'common flow up' 형상의 와류발생기가 정렬형 관군에서 설치될 때 Reynolds수(유로 높이의 배를 기준으로)가 $300{\~}2700$ 범위에서 열전달촉진은 10까지 향상하였고, 동시에 압력강하는 $8\%{\~}15\%$ 감소하였다. 삼각형 와류발생기가 부착된 휜-관군의 성능이 상대적으로 작은 압력강하 때문에 사각형 와류발생기가 부착된 휜-관군의 성능보다 좋게 나타났다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2536-2539
• /
• 2008

A study has been made on how to occur inertial oscillations in a rotating flow. The flow is considered to be induced by differentially-rotating top and bottom disks with infinite radius. The top and bottom disks are assumed to be set in motion over a finite initial start-up time duration from initial solid body rotation ($\Omega$) to each finial state, i.e., the top disk is rotating at the angular velocity (${\Omega}+{\Delta}{\Omega}$) and the bottom disk (${\Omega}-{\Delta}{\Omega}$). The system Reynolds number, which is a reciprocal of conventional Ekman number in rotating flows, is very high so that a boundary layer flow near disks is pronounced. From a strict theoretical analysis, it is clearly found the fact that inertial oscillation in a rotating flow is caused by excessive input of torque during start-up phase. Above finding comes from the following physics of theoretical result: in the case of abrupt start-up within very shorter time-duration than spin-up time scale, the inertial oscillation is magnified but it could be completely depressed in the case of mildly accelerated start-up, i.e., start-up process being established over diffusion time scale.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.76-84
• /
• 1996

The nozzle geometry and up-stream inject ion condition affect the characteristics of flow inside the nozzle. such as turbulence and cavitation bubbles. Flow details in fuel nozzle orifice with sudden contraction of cross sectional area have been investigated both experimentally and numerically. The measurements of velocities of internal flow in a scaled-up nozzle with different length to diameter rat io(L/d) were made by laser Doppler velocimetry in order to clarify the effect of internal flow on the characteristics of fuel spray. Mean and fluctuating velocities and discharge coefficients were obtained at various Reynolds numbers. The turbulent intensity and turbulence kinetic energy in a sharp inlet nozzle were higher than that in a round inlet nozzle. Calculations were also performed for the same nozzles as scaled-up experimental nozzles using the SIMPLE algorithm. External spray behavior under different nozzle geometry and up-stream flow conditions using Doppler technique and visualization technique were also observed.

• 한국농공학회논문집
• /
• 제48권6호
• /
• pp.113-124
• /
• 2006

The feasibility of the up- and down-flow constructed wetland was examined fur rural wastewater treatment in Korea. Many constructed wetland process was suffered from substrate clogging and high plant stresses because of long term operation. The up- and down-flow constructed wetland process used porous granule materials (charcoal pumice : SSR=10:20:70) for promoting intake rate of nutrient to plant, and especially flow type was designed continuously repeating from up-flow to down-flow. $BOD_5$ and SS was removed effectively by the process with the average removal rate being about 75% respectively. The wetland process was effective in treating nutrient as well as organic pollutant. Removal of TN and TP were more effective than other wetland system and mean effluent concentrations were approximately 7.5 and $0.4mg\;L^{-1}$ which satisfied the water quality standard for WWTPs. The treatment system did not experience any clogging or accumulations of pollutants and reduction of treatment efficiency during winter period because constructed polycarbonate glass structure prevented temperature drop. Considering stable performance and effective removal of pollutant in wastewater, low maintenance, and cost-effectiveness, the up- and down-flow constructed wetland was thought to be an effective and feasible alternative in rural area.

• 대한기계학회논문집B
• /
• 제30권12호
• /
• pp.1139-1146
• /
• 2006

Light Oil Flow Standard System(LOFSS) in Korea Research Institute of Standards and Science(KRISS) was designed for oil flowmeter calibration. In order to extend the flow range from 120 $m^3/h$ to 200 $m^3/h$, the build-up technique was applied with two positive displacement flowmeters as master flowmeter. The master flowmeters were calibrated against with LOFSS, which has 0.04 % uncertainty of flow quantity determination, then the test flowmeter is calibrated against two master flowmeters. For uncertainty analysis, the repeatability of master flowmeters, the variation of the fluid density and the pipe volume due to temperature change were scrutinized. The contribution of each uncertainty factors to the calibrator and the correlation of each factors were discussed. For investigating the feasibility of uncertainty analysis, a turbine flowmeter as a transfer package was tested with LOFSS and two reference flowmeter. The hypothesis test for both results was coincide with a 95 % significant level. This means that the uncertainty analysis procedure of the calibrator is reasonable and the extension of flow range with master meters was carry out successfully.

• Journal of Welding and Joining
• /
• 제27권1호
• /
• pp.71-78
• /
• 2009

In the circumferential welding of pipe, welding phenomenon changes with the position of pipe. Especially in the overhead position, back bead of vertical-up position would be sunk. To investigate the size of back bead and keyhole with the change of the flow rate of pilot and shield gas at each position, bead-on plate welds were conducted on 6mm thickness SS400 with inclined-up position. When the rest of welding conditions remained constant, the width of back bead was increased as the flow rate of pilot gas was increased. And back bead tended to convex as the flow rate of shield gas was increased.

• 대한기계학회논문집B
• /
• 제25권3호
• /
• pp.339-346
• /
• 2001

The impulsive spin-up flow in a shallow rectangular container is analyzed numerically by quasi 3-D unsteady laminar flow. In the non-inertia coordinates, the flow is generated by the virtual forces as Coriolis force, etc.. After the boundary layers grow up near sidewalls, primary vortexes separate from the sidewalls. As the Reynolds number increases, the subsidiary vortexes take place in the boundary layer. The rigid body rotation is started from the inner region and propagated to the outer region, finally all the fluid reaches the rigid body rotation. According to the Reynolds number and the aspect ratio, the development of vortex pattern is symmetric or asymmetric.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2003년도 학술대회지
• /
• pp.442-445
• /
• 2003

최근 도심지 고층건축공사가 증가하면서 건설자원의 효율적인 관리가 중요시되고 있으나 현재 국내 건설현장에서 건설자재의 공급에 대한 많은 문제점을 가지고 있다. 공정과 연계되지 못한 자재의 조달 및 양중은 현장 내 재고 증가 및 작업지연을 유발하면, 복잡한 정보전달 체계는 관련 작업의 의사결정의 지연의 원인으로 작용하여 결과적으로 공사기간에 절대적인 영향을 미치고 있다. 따라서 공정진행을 고려한 조달 및 양중작업에서 각 공사담당자간의 효율적인 정좌전달 체계의 구축은 효과적인 공사수행을 위해 필수적이다. 본 연구에서는 사례조사를 통해 건설자재의 조달 및 양중작업의 문제점을 분석하여 가치흐름분석을 통해 구체적인 낭비요소를 추출한 뒤, 공사참여자간의 의사소통 체계를 구축 및 양중계획 업무흐름 개선방안을 제시하였다. 개선방안은 web을 기반으로 한 조달 및 양중시스템의 전반적인 체계로서 활용될 것이다.

• 설비공학논문집
• /
• 제17권9호
• /
• pp.799-807
• /
• 2005

The flow characteristics and the heat transfer rate on a surface by the interaction of a pair of vortices are studied numerically. To analyze the common flow up produced by vortex generators in a rectangular channel flow, the pseudo-compressibility viscous method is introduced into the Reynolds-averaged Navier-Stokes equation for 3-dimensional unsteady, incompressible viscous flows. To predict turbulence characteristics, a two-layer $k-\varepsilon$ turbulence model is used on the flat plate 3-dimensional turbulence boundary The computational results predict accurately Reynolds stress, turbulent kinetic energy and flow field generated by the vortex generators. The numerical results, such as thermal boundary layers, skin friction characteristics and heat transfers, are also reasonably close to the experimental data.