• 한국강구조학회 논문집
• /
• 제26권3호
• /
• pp.241-250
• /
• 2014

층간소음에 대응할 수 있는 유닛모듈러 경량합성바닥 구조시스템을 제안하고, 이러한 바닥판에 대한 내력 및 거동을 실험연구를 통해 평가하고자 하는 것이 본 연구의 목표이다. 평데크와 철근트러스 데크를 활용하여 제안된 형상별로 각각 3개씩 총 9개의 경량합성바닥판 실험체를 제작하여 실험을 수행하였다. 실험결과, 실험체의 파괴 형태는 바닥판의 중앙부에서 처짐으로 인한 휨변형에 의해 지배되었으며 종국으로 바닥판 상부에 콘크리트 압괴가 발생하는 동일한 파괴양상을 나타내었다. 또한, 사용하중 상태에서는 구조적으로 안전하고, 사용성 측면에서도 우수한 것으로 나타났다. 이론적 공칭하중에 대한 실험 항복하중의 비는 0.86~1.27의 분포로 평균 1.04로 나타났으며, 분포도 측면에서 변동계수는 0.154로 나타나 비교적 잘 일치하는 것으로 나타났다.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.76-83
• /
• 2010

Recently, as the current and future emission regulations go stringent, the research of NOx reduction has become a subject of increasing interest and attention in diesel engine. Selective Catalytic Reduction (SCR) is one of the effective technology to reduce NOx emission from diesel engine. Especially, Urea-SCR that uses urea as a reductant is becoming increasingly popular as a cost effective way of reducing NOx emissions from heavy duty vehicles. In this research, we designed urea injector and DCU (Dosing Control Unit) specially developed for controlling the Urea-SCR process onboard vehicles. As passenger and commercial diesel engine experiment, we grasped characteristics of NOx emission and SCR catalyst temperature level in advance. As a result, highest NOx emission level was shown in condition of low engine speed and high load. On the other hand, SCR catalyst temperature was highest at high engine speed and load. On the basis of these result, we conducted the NOx reduction test at steady engine operating conditions using the urea injector and DCU. It was shown that 74% NOx conversion efficiency on the average and 97% NOx conversion efficiency was obtained at high SCR catalyst temperature.

• 한국환경과학회지
• /
• 제26권8호
• /
• pp.939-953
• /
• 2017

For the development of flow duration curves for the management of 41 Total Maximum Daily Load (TMDL) units of the Nakdong River basin, first, an equation for estimating daily flow rates as well as the level of correlation (correlation and determination coefficients) was extrapolated through regression analysis of discrete (Ministry of Environment) and continuous (Ministry of Land, Infrastructure and Transportation) measurement data. The equation derived from the analysis was used to estimate daily flow rates in order to develop flow duration curves for each TMDL unit. By using the equation, the annual flow duration curves and flow curves, for the entire period and for each TMDL unit of the basin, were developed to be demonstrated in this research. Standard flow rates (abundant-, ordinary-, low- and drought flows) for major flow duration periods were calculated based on the annual flow duration curves. Then, the flow rates, based on percentile ranks of exceedance probabilities (5, 25, 50, 75, and 95%), were calculated according to the flow duration curves for the entire period and are suggested in this research. These results can be used for feasibility assessment of the set values of primary and secondary standard flow rates for each river system, which are derived from complicated models. In addition, they will also be useful for the process of implementing TMDL management, including evaluation of the target level of water purity based on load duration curves.

• 전기전자학회논문지
• /
• 제24권2호
• /
• pp.632-637
• /
• 2020

비간섭적 개별 전기 기기 부하 식별(NILM)은 단일 미터기에서 측정한 총 소비 전력을 사용하여 가정이나 회사에서 개별 전기 기기의 소비 전력과 사용 시간을 효율적으로 모니터링할 수 있는 방법이다. 본 논문에서는 스마트팜의 소비 전력 데이터 취득 시스템에서 LTE 모뎀을 통해 서버로 수집된 총 소비 전력량, 개별 전기 기기의 전력량을 HDF5 형태로 변환하고 NILM 분석을 수행하였다. NILM 분석은 오픈소스를 사용하여 잡음제거 오토인코더(Denoising Autoencoder), 장단기 메모리(Long Short-Term Memory), 게이트 순환 유닛(Gated Recurrent Unit), 시퀀스-투-포인트(sequence-to-point) 학습 방법을 사용하였다.

• 구강회복응용과학지
• /
• 제22권1호
• /
• pp.75-87
• /
• 2006

The purpose of this study was to investigate the effects of prostheses misfit, cantilever on the stress distribution in the implant components and surrounding bone using three dimensional finite element analysis. Two standard 3-dimensional finite element models were constructed: (1) 3 ITI implant supported, 3-unit fixed partial denture and (2) 3 ITI implant supported, 3-unit fixed partial denture with a distal cantilever. variations of the standard finite element models were made by placing a $100{\mu}m$ or $200{\mu}m$ gap between the fixture, the abutment and the crown on the second premolar and first molar. Total 14 models were constructed. In each model, 244 N of vertical load and 244 N of $30^{\circ}$ oblique load were placed on the distal marginal ridge of the distal molar. von Mises stresses were recorded and compared in the crowns, abutments, crestal compact bones, and trabecular bones. The results were obtained as follows: 1. In the ITI implant system, cement-retained prostheses showed comparatively low stress distributions on all the implant components and fixtures regardless of the misfit sizes under vertical loading. The stresses were increased twice under oblique loading especially in the prostheses with cantilever, but neither showed the effects of misfit size. 2. Under the oblique loading and posterior cantilever, the stresses were highly increased in the crestal bones around ITI implants, but effects of misfit were not shown. Although higher stresses were shown on the apical portion of trabecular bones, the effects by misfit were little and the stresses were increased by the posterior cantilever. 3. When the cement loss happened in the ITI implant supported FPD with misfit, the stresses were increased in the implant componets and supporting structures.

• 해양환경안전학회지
• /
• 제18권3호
• /
• pp.279-285
• /
• 2012

LNGC 주기관의 크랭크 챔버 내 유증기 폭발 방지를 위해 기존의 이산화탄소 가스인젝터가 부착된 오일미스트 감지기 외에 불활성가스 시스템을 설치할 필요가 있다. 특히, LNGC 선박은 액체질소를 손쉽게 확보할 수 있는 장점이 있기 때문에 액체질소를 이용한 불활성가스 시스템을 도입하기 위한 설계 기초 단계로서 해석적 연구를 시행하였다. 또한 액체질소 최소 소모량 시스템을 개발하기 위하여 층상류 모델을 적용하였으며, 층상류 흐름에 미치는 유로관경, 포화압력과 선박동요에 따른 배관 기울기 등의 영향에 대해서도 조사하였다. 또한 질소와 같은 극저온 유체들과 여기에 사용된 예측 모델과의 비교 검토를 통하여 극저온 유체에 대해서도 모델의 유효성을 검증하였으며, 액체질소 불활성가스 시스템의 액체질소를 가스로 상변환 시키는데 소요되는 가열기의 열부하도 예측할 수 있었다.

• 설비공학논문집
• /
• 제21권5호
• /
• pp.297-304
• /
• 2009

The aim of this study is to investigate the cooling performance of ground source multi-heat pump systems with a vertical single U-tube GLHX(U-tube system) and a vertical double tube GLHX(double tube system), which were installed in a school building located in Cheonan. All systems were operated in a part load conditions for all day, and the maximum COP of the single U-tube system and the double tube system were 6.2 and 5.2 at cooling mode, respectively. The double tube GLHX designed by the GLHEPRO, commercial program, was estimated to have the same performance as the U-tube GLHX, because the inlet temperatures of each outdoor unit heat exchanger for the former was similar to the latter. However, it is needed to prove the long tenn performance. It is suggested that the new algorithms to control the flow rate of secondary fluid for GLHX according to load variation have to be developed in order to enhance the performance of the system.

• 한국태양에너지학회 논문집
• /
• 제22권3호
• /
• pp.47-56
• /
• 2002

The office is an excellent candidate for implementing daylighting techniques because of the relatively high electric lighting power densities and long daytime use pattern. The quantity of light available for a space can be translated in term of the amount of energy savings through a process of a building energy simulation. To get significant energy savings in general illumination, the electric lighting system must be incorporated with a daylight - activated dimmer control. A prototype configuration of an office interior has been established and the integration between the building envelope and lighting and HVAC systems is evaluated based on computer modeling of a lighting control facility. First of all, an energy-efficient luminaire system is designed for both a totally open-plan office interior and a partitioned office. A lighting design and analysis program, Lumen-Micro 2000 predicts the optimal layout of a conventional fluorescent lighting fixture to meet the designed lighting level and calculates unit power density, which translates the demanded amount of electric lighting energy. A dimming control system integrated with the contribution of daylighting has been applied to the operating of the artificial lighting. Annual cooling load due to lighting and the projecting saving amount of cooling load due to daylighting under overcast diffuse sky are evaluated by a computer software, ENER-Win. In brief, the results from building energy simulation with measured daylight illumination levels and the performance of lighting control system indicate that daylighting can save over 70 percent of the required energy for general illumination in the perimeter zones through the year. A 25 % of electric energy for cooling may be saved by dimming and turning off the luminaires in the perimeter zones.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.364-365
• /
• 2011

This study develops a new system for generation system simulation and operational planning (namely, KPWR-X) including GMS(Generator Maintenance Scheduling), UC(Unit Commitment), and LF(Load Forecasting) for new power system environment in recent. The KPWR-X provides operator and planner to help the generation system more safely and economically. GUI developed in this study makes operator feel in convenient to control whole power system. In future, it is expected that generation company, ISO, and fuel procurement, etc. may use an instructional tool developer's suggestion for application. It will be also applicable to establish the operational strategies for generation control, fuel procurement and power system risk management.

• 한국자동차공학회논문집
• /
• 제9권3호
• /
• pp.100-107
• /
• 2001

The main goals of the automotive suspension systems are to isolate roadway unevenness from the tire and to improve vehicle stability. To overcome the performance limitation of the passive systems the active systems which completely replace the passive spring and damper elements with a force generating actuator has been studied. However, application of the system has been limited because it has required a significant amount of power. Recently, alternative systems which retain passive elements but include active elements have been developed to reduce the power required. Those systems are mostly focused on the control system which compresses the spring-damper directly. In this study, a new type of power efficient control system which makes the spring-damper unit slide in side way is studied. After constructing the control system including dynamic modeling and motion control, two types of alternative control systems are compared in view of power consumption and dynamic attitudes such as roll responses as well as heave responses. Also, a half car bond graph model is developed to show clearly the significant differences in performances between two control systems.