• 복식
• /
• 제54권1호
• /
• pp.1-10
• /
• 2004

The purpose of this study was to compare the efficiency of four different cleaning method of silk and to fabrics, which were excavated from the sixteenth century tombs. The four cleaning methods were hand washing in water and hand washing in solvent, washing in ultrasonic cleaner, and using of ultrasonic gun after washing in ultrasonic cleaner. The following is the result of the experiment: ㆍBoth silk and jute fabrics shrank the most after hand-wash in water. This cleaning method decreased their thickness the most but changed their strength the least. However, the color of the fabric changed the most after had-wash in water. This washing method might discolor the dyed fabric, so one must check the condition of the fabric thoroughly before washing it. ㆍThe weight and the thickness of the fabric changed little after ultrasonic cleaning. This cleaning method, therefore. is less efficient than hand-water-wash. The use of ultrasonic gun after ultrasonic wash for partial cleansing enhanced the efficiency a little. Nevertheless, this method left stain around the area where the gun was used, and the injected water could damage the fabric. ㆍThe excavated fabric became softer in the cleaning process as the dirt was washed away. In both cases of silk and jute fabrics cleaning, solvent made the fabric softer than water. Washed in solvent, the fabric did not swell. But water penetrated to the fiber during the cleaning process and made the fabric swell. When the water evaporates, the swollen fiber structure collapses and the fabric become stiff. Ultrasonic wash did not cause much change in the flexibility of the fabric, for this method does not remove the dirt as effectively as the other method.

• Journal of Mechanical Science and Technology
• /
• 제14권3호
• /
• pp.320-330
• /
• 2000

It is desirable to perform nondestructive evaluation (NDE) to assess material properties and part homogeneity because the manufacturing of carbon/carbon brake disks requires complicated and costly processes. In this work several ultrasonic techniques were applied to carbon/carbon brake disks (322mm ad, 135mm id) for the evaluation of spatial variations in material properties that are attributable to the manufacturing process. In a large carbon/carbon disk manufactured by chemical vapor infiltration (CYI) method, the spatial variation of ultrasonic velocity was measured and found to be consistent with the densification behavior in CYI process. Low frequency (e.g., 1-5MHz) through-transmission scans based on both amplitude and time-of-flight of the ultrasonic pulse were used for mapping out the material property inhomogeneity. Images based on both the amplitude and the time-of-flight of the transmitted ultrasonic pulse showed significant variation in the radial direction. The radial variations in ultrasonic velocity and attenuation were attributed to a density variation caused by the more efficient densification of pitch impregnation near the id and od and by the less efficient densification away from the exposed edged of the disk. Ultrasonic velocities in the edges of the disk. Ultrasonic velocities in the thickness direction were also measured as a function of location using dry-coupling transducers ; the results were consistent with the densification behavior. However, velocities in the in-plane directions (circumferential and radial) seemed to be affected more by the relative contents of fabric and chopped fiber, and less by the void content.

• 전기학회논문지
• /
• 제61권2호
• /
• pp.276-283
• /
• 2012

In this paper, a practical quasi-optimal DOA(direction of arrival) estimator is proposed in order to develop a one-axis gimbaled ultrasonic source tracker for mobile robot applications. With help of the gimbal structure, the ultrasonic moving source tracking problem can be simply reduced to the DOA estimation. The DOA estimation is known as one of the representative long-pending nonlinear filtering problems, but the conventional nonlinear filters might be restrictive in many actual situations because it cannot guarantee the reliable performance due to the use of nonlinear signal model. This motivates us to reformulate the DOA estimation problem in the linear robust state estimation setting. Based on the assumption that the received ultrasonic signals are noisy sinusoids satisfying linear prediction property, a linear uncertain measurement model is newly derived. To avoid the DOA estimation performance degradation caused by the stochastic parameter uncertainty contained in the linear measurement model, the recently developed NCRKF (non-conservative robust Kalman filter) scheme [1] is utilized. The proposed linear DOA estimator provides excellent DOA estimation performance and it is suitable for real-time implementation for its linear recursive filter structure. The effectiveness of the suggested DOA estimation scheme is demonstrated through simulations and experiments.

• 한국추진공학회지
• /
• 제11권1호
• /
• pp.34-42
• /
• 2007

초음파를 이용한 추진기관의 비파괴검사는 X-ray 검사에 비하여 경제성이 우수하고, X-ray 검사 시 취약한 미접착, 손상 등의 결함 검출이 우수한 편이다. 그리고 전용 시설 없이 현장에서 실시간으로 검사가 가능하며 방사선 작업에 비하여 안전한 방법이다. 본 논문에서는 고체 추진제에 대한 초음파 특성을 분석하고, 추진제/라이너 미접착에 대한 내측과 외측 검사 방법 및 추진제 손상에 의한 미세 크랙 검출에 대하여 실험 및 분석하였다. 실험 결과, 추진제/라이너 미접착에 대한 내.외측 검사에 있어서 검출 가능성을 보였으며, 그리고 손상에 의한 추진제 미세 크랙도 초음파의 감쇠특성을 이용하여 검출 가능함을 보였다.

• 한국추진공학회지
• /
• 제12권2호
• /
• pp.40-47
• /
• 2008

초음파를 이용한 추진기관의 접착 계면 검사는 결함 검출 능력과 경제성이 우수하다고 알려져 있다. 하지만, 추진기관의 접착 구조는 다중 계면이므로 송신 펄스와 수신 펄스의 시간 간격이 짧아서 반사 신호의 분리가 어렵기 때문에 초음파의 신호 분석에는 많은 시간과 노력이 소요된다. 이런 이유로 추진기관의 초음파시험은 연소관과 내열재 사이의 미접착 결함과 같이 극히 제한된 영역에 대해서만 자동화 시스템으로 수행하고 있다. 본 논문에서는 기존의 초음파시험으로 검출이 불가능했던 라이너와 추진제 미접착 결함을 초음파의 공진 현상과 램파 특성을 이용하여 검출하는 새로운 기법에 대해 기술하였다.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.113-119
• /
• 2002

The effect of ultrasonic radiation is reported for silica-poly(ethylene glycol) system prepared without the solvent using sol-gel processing by varying various parameters such as ultrasonic irradiation time, PEG content and HCl/TEOS molar ratio. The property of sonogel is compared with classic gel which has been prepared with ethanol as a solvent by traditional sol-gel processing. SEM, BET, DTA-TGA, density and Vickers hardness measurements are carried out for analyzing the samples. The gelation time is found strongly dependent on radiation time, PEG content and pH value, and has been discussed on the basis of existing theories. The $SiO_2-10$ & 20 wt% PEG sonogel exhibited superior optical, physical and gel properties as compared to the classic gel, hence, found suitable for device applications. The ultrasonic radiation increased the density and surface area, and also reduced the pore size which is well supported by the shift in the peak of DTA curve. The DTA thermogram was found similar to that of pure silica gel.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.55-59
• /
• 2007

초음파를 이용한 추진기관의 접착 계면 검사는 결함 검출 능력과 경제성이 우수하다고 알려져 있다. 하지만, 추진기관의 접착 구조는 다중 계면이므로 송신 펄스와 수신 펄스의 시간 간격이 짧아서 반사 신호의 분리가 어렵기 때문에 초음파의 신호 분석에는 많은 시간과 노력이 소요된다. 이런 이유로 추진기관의 초음파시험은 연소관과 내열재 사이의 미접착 결함과 같이 극히 제한된 영역에 대해서만 자동화 시스템으로 수행하고 있다. 본 논문에서는 기존의 초음파시험으로 검출이 불가능했던 라이너와 추진제 미접착 결함을 초음파의 공진 현상과 램파 특성을 이용하여 검출하는 새로운 기법에 대해 기술하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.324-324
• /
• 2008

Piezoelectric ceramics is an active element that makes stator to vibrate to generate rotational force in ultrasonic motors. In drive of ultrasonic motors, many factors that affect to the resonance characteristics of piezoelectric ceramics exist. For example, those factors are bonding condition with elastic body, the magnitude of electric field, the normal force for frictional drive and the emission of heat due to vibration and friction and so on. Therefore, it is important to research the inclination of property variation of piezoelectric ceramics in circumstance that has complex elements. In this paper, we focused and analyzed the resonance characteristics of ultrasonic motor due to the magnitude of the driving voltage and normal force.

• 한국전기전자재료학회논문지
• /
• 제25권12호
• /
• pp.990-995
• /
• 2012

A piezoelectric ultrasonic bone surgical instrument, usually used to remove the tartar out of teeth or to cut the dentine of the tooth, is a recently popular instrument for dental treatment due to its several merits such as small size, low-electric power and precision control of surgical operation. It has typically two parts of a tip and vibration system which is also composed of head, piezoelectric elements and tail-mass. In order to improve the performance of the instrument, it is important to standardize the size of the vibration system without tip for high performance. In this study, a Finite Element Analysis (FEA) was utilized to optimize the structure of ultrasonic instrument in vibration system. Consequently, this study revealed that influence of several tips on property were minimized and it showed good property at the frequency range of 22~32 kHz.

• Journal of Mechanical Science and Technology
• /
• 제16권12호
• /
• pp.1627-1632
• /
• 2002

In this paper, a simplified ultrasonic CT system, which uses the information in three directions, that is, 90°, ＋45° and －45°about the inspection plane, is applied to the high strength steel, and the frequency analysis method for enhancing the C scan or CT image is developed. This frequency analysis method is based on the frequency response property of the material. By comparing the magnitudes in the frequency domain, the special frequency which shows a significant difference between the welded joint and base material was found and used to obtain a C scan or CT image. Experimental results for several kinds of specimens, having a welded joint by electron beam welding, a weld joint by arc welding, on a fatigue crack, showed that the obtained C scan or CT image has better resolution than the results of previous experiments using the maximum value of the received waveform.