• 방송공학회논문지
• /
• 제20권1호
• /
• pp.26-39
• /
• 2015

최근 몇 년간 차세대 방송으로 일컬어지는 UHD (Ultra High Definition) 방송 기술에 대한 많은 연구 및 개발이 진행되고 있다. 사람들의 이목이 집중되는 큰 스포츠 이벤트는 새로운 방송 기술을 홍보하기 위해 좋은 기회인만큼, KBS에서는 2014년에 있었던 세 번의 큰 스포츠 이벤트인 KBL (Korean Basketball League) 프로농구 결승전, 2014 브라질 월드컵, 2014 인천 아시안게임에 대해 4K 라이브 중계방송을 실시하였다. 특별히 KBL 프로농구 결승전은 세계 최초 지상파 4K 라이브 중계방송이었으며, 월드컵과 아시안게임에 대해서는 UHDTV를 보유한 시청자들이 각자의 집에서 UHD 방송을 즐길 수 있었다. 본 논문에서는 세 번의 스포츠 이벤트에 대한 전체적인 제작 및 전송과정에 대해 정리하였다. 특별히 경기 현장에서의 방송 제작, 실시간 HEVC 인코딩, SFN 전송, 국가과학기술연구망인 KREONOET을 통한 4K 무압축 영상에 대한 IP 전송 등에 대해 설명하였다.

• 한국광학회지
• /
• 제12권2호
• /
• pp.135-142
• /
• 2001

최근 플라스틱 광섬유(Plastic Optical Fiber, POF)가 홈 네트워크(Home Network) 및 LAN(Local Area Network)의 새로운 통신채널로 등장하였다. 특히 PMMA 계에 기반을 둔 언덕형 굴절률 분포 플라스틱 광섬유(Graded Index Plastic Optical Feiber)는 500nm와 650nm 근처에서 아주 적은 손실을 가지므로 이 파장영역에서의 광원으로서 극초단 광펄스 생성이 요구되고 있다. 본 연구에서는 650nm InGaAIP FP(fabry perot) LD와 간단한 RF(radio frequency)소자들을 이용한 회로를 구성하고 이득스위칭 기술을 사용하여 1GHz의 펄스 반복율을 가지고 33.3psec 정도의 짧은 반치선폭(FWHM)을 가지는 광펄스를 생성시키는데 성공하였다. 이득스위칭 된 광펄스는 주입되는 직류전류(DC bias current)와 변조되는 주파에 따라 반치선폭은 33.3-82.8 psec, 펄스 에너지는 0.97-9.69pJ의 값을 얻었다. 또한 CW 발진과 이득스위칭 된 광펄스의 스펙트럼 폭은 각각 0.44nm, 150nm로 됨을 측정하였다. 이러한 결과를 가지는 연속적인 광펄스는 직류전류와 VCO에 의한 변조주파수의 적절한 선택에 따라 초고속 근거리 광통신분야 뿐만 아니라 여러 가지 초고속 광소자 및 전자소자의 특성평가 등에 응용될수 있을 것으로 예상된다.

• 한국전자통신학회논문지
• /
• 제17권4호
• /
• pp.555-562
• /
• 2022

4차 산업혁명시대에 반지하 실내 복도 환경에서 새로운 전파 수요를 발굴하기 위해 본 논문에서는 주파수 6, 10, 17 GHz의 전파 특성에 대한 측정 및 분석하였다. 측정한 실내 내부 환경은 3면의 강의실과 외면의 유리창으로 구성되어있는 일자형 복도이다. 본 연구는 이러한 환경에 맞게 측정 시나리오 개발과 측정 시스템을 구성하였다. 송신 안테나는 고정하고 수신 안테나 위치의 거리에 따라 가시선 환경에서 주파수 영역과 시간영역 전파 특성을 측정하여 분석 하였다. 주파수 영역은 FI(: Floating intercept) 경로 손실 모델의 매개변수와 R-squared 값의 0.5 이상에 대한 신뢰도를 얻었다. 또한, 시간 영역은 RMS(: Root mean square) 지연 확산과 K-factor의 누적 확률에서 6 GHz는 전파 전달도가 높고, 17 GHz는 전파 전달도가 낮은 결과를 얻었다. 이러한 연구 결과는 반지하 실내 복도 환경에서 WIFI 6 이상이나 5G 이상에 대해 초 연결과 초 지연 인공지능 서비스를 제공하는데 효과가 있을 것이다.

• 전기학회논문지
• /
• 제57권6호
• /
• pp.909-914
• /
• 2008

A coupling capacitor voltage transformer(CCVT) is used in an extra or ultra high voltage system to obtain the standard low voltage signal for protection. To avoid the phase angle error between the primary and secondary voltages, a tuning reactor is connected between a capacitor and a voltage transformer. The inductance of the reactor is designed based on the power system frequency. If a fault occurs on the power system, the secondary voltage of the CCVT contains some errors due to a dc offset component and harmonic components resulting from the fault. The errors become severe in the case of a close-in fault. This paper proposes an algorithm for compensating the secondary voltage of a CCVT in the time-domain. From the measured secondary voltage of the CCVT, the secondary and primary currents are obtained; then the voltage across the capacitor and the inductor is calculated and then added to the measured secondary voltage to obtain the correct primary voltage. Test results indicate that the proposed algorithm can compensate the distorted secondary voltage of the CCVT irrespective of the fault distance, the fault inception angle, and the burden of the CCVT.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.344-354
• /
• 2015

In order to study the development of partial discharge (PD) under typical protrusion defects in gas-insulated switchgear, we applied step voltages on the defect and obtained the ${\varphi}-u$ and ${\varphi}-n$ spectrograms of ultra-high frequency (UHF) PD signals in various PD stages. Furthermore, we extracted seven kinds of features to characterize the degree of deterioration of insulation and analyzed their values, variation trends, and change rates. These characteristics were inconsistent with the development of PD. Hence, the differences of these features could describe the severity of PD. In addition, these characteristics could provide integrated characteristics regarding PD development and improve the reliability of PD severity assessment because these characteristics were extracted from different angles. To explain the variation laws of these seven kinds of parameters, we analyzed the relevant physical mechanism by considering the microphysical process of PD formation and development as well as the distortion effect generated by the space charges on the initial field. The relevant physical mechanism effectively allocated PD severity among these features for assessment, and the effectiveness and reliability of using these features to assess PD severity were proved by testing a large number of PD samples.

• Journal of Electrical Engineering and Technology
• /
• 제10권2호
• /
• pp.574-585
• /
• 2015

This paper aims to improve the performance of conventional direct torque control (DTC) drives proposed by Takahashi by extending the idea for 5-level inverter. Hybrid cascaded H-bridge topology is used to achieve inverter voltage vector composed of 5-level of voltage. Although DTC is very popular for its simplicity but it suffers from some disadvantages like- high torque ripple and uncontrollable switching frequency. To compensate these shortcomings conventional DTC strategy is modified for five levels voltage source inverter (VSI). Multilevel hysteresis controller for both flux and torque is used. Optimal voltage vector selection from precise lookup table utilizing 12 sector, 9 torque level and 4 flux level is proposed to improve DTC performance. These voltage references are produced utilizing a hybrid cascaded H-bridge multilevel inverter, where inverter each phase can be realized using multiple dc source. Fuel cells, car batteries or ultra-capacitor are normally the choice of required dc source. Simulation results shows that the DTC drive performance is considerably improved in terms of lower torque and flux ripple and less THD. These have been experimentally evaluated and compared with the basic DTC developed by Takahashi.

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.192-199
• /
• 2016

With changes in insulated defects, the environment, and so on, new partial discharge (PD) data are highly different from the original samples. It leads to a decrease in on-line recognition rate. The UHF signal and pulse current signal of four kinds of typical artificial defect models in gas insulated switchgear (GIS) are obtained simultaneously by experiment. The relationship map of ultra-high frequency (UHF) cumulative energy and its corresponding apparent discharge of four kinds of typical artificial defect models are plotted. UHF cumulative energy and its corresponding apparent discharge are used as inputs. The support vector machine (SVM) incremental method is constructed. Examples show that the PD SVM incremental method based on simulated annealing (SA) effectively speeds up the data update rate and improves the adaptability of the classifier compared with the original method, in that the total sample is constituted by the old and new data. The PD SVM incremental method is a better pattern recognition technology for PD on-line monitoring.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 춘계학술대회 논문집
• /
• pp.145-147
• /
• 2007

Fluorescent induction lamps are assembly of a Low Pressure Mercury discharge vessel and an inductive power coupler. A vessel containing at least a Low Pressure Mercury vapor, which will be energized by means of the Inductive Coupler. The Ultra Violet radiation from the resulting discharge is converted by a layer of fluorescent material into visible light. The discharge vessel may have means of mechanical fixation to position it to the Inductive power coupler. The component to transform High Frequency electrical energy, by means of induction, in order to energize the Low Pressure Mercury in the discharge vessel. The component includes electrical connection. Fluorescent induction lamps don't have international standards yet. So we try to correspond Korea standards to international standards.

• Journal of Astronomy and Space Sciences
• /
• 제34권2호
• /
• pp.111-118
• /
• 2017

A ultra low frequency (ULF) wave, Pi2, has been reported to occur during periods of extremely quiet magnetospheric and solar wind conditions. And no statistical study on the Pi2 has been performed during extremely quiet conditions, using satellite observations to the author's knowledge. Also Pi2 pulsations in the space fluxgate magnetometers near perigee failed to attract scientist's attention previously. In this paper, Pi2 pulsations detected by the Van Allen probe satellites (VAP-A & VAP-B) were investigated statistically. During the period from October 2012 to December 2014, ninety six Pi2 events were identified using VAP when Kp = 0 while using Kakioka (KAK, L = 1.23) as a reference ground station. Seventy five events had high coherence between VAP-Bz and H components at KAK station. As a result, it was found that 77 % of the events had power spectra between 5 and 12 mHz, which differs from the regular Pi2 band range of from 6.7 to 25 mHz. In addition, it was shown that it is possible to observe Pi2 pulsations from space fluxgate magnetometers near perigee. Twenty two clean Pi2 pulsations were found where L < 4 and four examples of Pi2 oscillations at different L shells are presented in this paper.

• Design & Manufacturing
• /
• 제1권1호
• /
• pp.51-56
• /
• 2007

As various manufacturing technology of optical glass is developed, the aspheric lenses are supplied to many fields. Electronic or measuring instruments equipped with aspheric lens have recently been used since aspheric lens is more effective than spheric one. However, it is still difficult manufacture glass lens because of high cost and the short life of core. The demands of the aspheric glass lenses increase since it is difficult to obtain the desirable performance in the plastic lens. For the mass production of aspheric lens, specific molds with precisely machined cores should be prepared. In order to obtain competitiveness in the field of industrial manufacturing, a reduction in the development period for the batch machining of products is required. It is essential to analyze the stress distribution and deformations of machining system which is used for manufacturing the aspheric lens using FEM software ANSYS. Finite element simulations have been performed in order to study the influence of machining system which is developed in this study on structures. It is very important to understand the structural behavior of machining system. This paper investigated the static analysis and dynamic analysis of machining system for aspheric lens to predict the damage due to loading.