• 콘크리트학회논문집
• /
• 제26권1호
• /
• pp.87-95
• /
• 2014

이 연구에서는 강섬유 보강 초고성능 콘크리트 보의 비틀림 거동을 파악하기 위한 실험연구를 수행하였다. 정사각형 단면을 갖는 6개의 초고성능 콘크리트 보 부재에 대해 하중재하실험을 수행하여 비틀림 거동 특성을 분석하였다. 부재의 실험변수는 강섬유 혼입량과 폐쇄 스터럽량이다. 강섬유 혼입량은 1.0% 및 2.0%로 변화하였고, 폐쇄 스터럽량은 0, 0.35% 및 0.70%로 변화하였다. 실험 결과는 강섬유양이 증가할수록 극한비틀림강도가 증가하고, 폐쇄스터럽량이 증가할수록 극한비틀림강도가 증가하는 것을 나타낸다. 또한, 비틀림 강도 예측식을 제안하였으며, 예측식은 콘크리트, 스터럽 및 강섬유의 비틀림 강도 기여분을 각각 고려하였다. 실험 결과를 이용하여 초고강도 콘크리트 보의 비틀림 강도 예측식의 적합성을 평가하고자 하였다. 비틀림강도 실험 결과를 예측값과 비교하였으며, 예측값은 실험 결과에 거의 근접하고 있는 것으로 나타났다. 따라서, 제안식을 이용하여 초고성능 콘크리트의 비틀림 강도를 효과적으로 예측할 수 있다고 판단된다.

• 대한토목학회논문집
• /
• 제4권1호
• /
• pp.27-48
• /
• 1984

본(本) 연구(硏究)는 한계상태(限界狀態) 설계(設計) 이론(理論)에 의한 철근(鐵筋)콘크리트 뼈대구조물(構造物)에 관(關)한 것이다. 한계상태이론(限界狀態理論)에 의한 철근(鐵筋)콘크리트 뼈대구조물(構造物)에 대한 최적설계(最適設計)의 문제형성(問題形成)은 철근(鐵筋)의 단면적(斷面積), 단면(斷面)의 폭(幅)과 유효고(有效高) 그리고 모멘트 감소율(減少率)을 설계변수(設計變數)로 취급(取扱)하는 비선형(非線型) 계획(計劃) 문제(問題)로 된다. 목적함수(目的凾數)는 철근(鐵筋)콘크리트 뼈대구조물(構造物)의 철근(鐵筋)과 콘크리트 및 거푸집의 비용(費用)을 고려(考慮)하는 총(總) 건설경비(建設經費)로 형성(形成)되고, 기본(基本) 제약조건식(制約條件式)들은 극한(極限) 한계상태(限界狀態)와 사용성(使用性) 한계상태(限界狀態)의 개념(槪念)을 내포하고 있다. 또한 CP110과 Hognestad et al. 이론(理論)에서 가정(假定)된 응력분포도(應力分布圖)를 극한(極限) 한계상태(限界狀態)를 위해 극한(極限) 저항단면력(抵抗斷面力)을 해석(解析)하는데 적용(適用)되었고, 사용성(使用性) 한계상태(限界狀態)를 위해서는 CP110의 규준(規準)만을 사용(使用)한다. 철근(鐵筋)콘크리트 뼈대구조물(構造物)의 최적화(最適化)를 위한 비선형(非線型) 계획(計劃) 문제(問題)를 풀기 위해서 적용(適用)된 최적화(最適化) 기법(技法)은 수정(修正) Newton-Raphson 법(法)을 이용한 SUMT 알고리즘이다. 본(本) 알고리즘을 2종(種)의 뼈대구조물(構造物)에 시행(試行)해 보았고, 본(本) 알고리즘의 수감성(收歛性), 적용가능성(適用可能性) 및 안정성(安定性)을 검토(檢討)하기 위해 문헌(文獻)(10)의 수치결과(數値結果)와도 비교분석(比較分析)하였다. 결론적(結論的)으로 수치분석(數値分析)을 통(通)하여 CP110과 Hognestad et al.의 경제성(經濟性) 비교(比較)와 본(本) 알고리즘의 적용가능성(適用可能性), 안정성(安定性), 수감성(收歛性) 및 확실성(確實性) 등에 대하여 논의(論議)되었다.

• Steel and Composite Structures
• /
• 제18권4호
• /
• pp.971-983
• /
• 2015

To promote greater acceptance and use of composite RCS systems, a two-bay two-story frame specimen with improved composite RCS joint details was tested in the laboratory under reversed cyclic loading. The test revealed superior seismic performance with stable load versus story drift response and excellent deformation capacity for an inter-story drift ratio up to 1/25. It was found that the failure process of the frame meets the strong-column weak-beam criterion. Furthermore, cracking inter-story drift ratio and ultimate inter-story drift ratio both satisfy the limitation prescribed by the design code. Additionally, inter-story drift ratios at yielding and peak load stage provide reference data for Performance-Based Seismic Design (PBSD) approaches for composite RCS frames. An advantage over conventional reinforced concrete and steel moment frame systems is that the displacement ductility coefficient of the RCS frame system is much larger. To conclude, the test results prove that composite RCS frame systems perform satisfactorily under simulated earthquake action, which further validates the reliability of this innovative system. Based on the test result, some suggestions are presented for the design of composite RCS frame systems.

• 콘크리트학회지
• /
• 제11권2호
• /
• pp.157-165
• /
• 1999

콘크리트 휨부재의 극한강도를 예측할 떼에는 부재의 크기효과는 고려하지 않는 것이 일반적이다. 그러나 콘크리트는 여러 형태의 하중에 대하여 부재의 크기가 증가함에 따라 강도가 감소하는 크기효과를 항상 나타낸다. 따라서 본 논문에서는 휨압축 부재에 대한 실험을 수행하여 크기효과를 검토하고자 한다. 이를 위하여 축 압축력과 휨모멘트를 동시에 받는 일련의 C형 공시체에 대한 실험을 수행하였다. 공시체의 크기는 3가지 였으며 콘크리트의 압축강도는 528 kg/$cm^2$로 하였다. 실험결과로부터 부재의 크기가 증가함에 따라 파괴시의 휨압축 강도가 감소하는 크기효과가 존재하며, 실린더 공시체의 축압축 강도보다 강도감소 현상이 더욱 분명함을 알 수 있었다. 최종적으로 실험자료에 대한 회귀분석을 수행하여 이를 예측할 수 있는 모델식을 제안하였다.

• 한국강구조학회 논문집
• /
• 제21권5호
• /
• pp.443-450
• /
• 2009

이 연구는 열하중이 발생하는 구조물에 강판 콘크리트구조를 적용하는 경우, 역학적 특성을 평가하기 위하여 수행하였다. 원자력발전소 구조물 중 사용후 핵연료 저장조 구조물과 같이, 구조물 내부는 지속적인 열 하중을 받고 구조물 외부는 대기에 노출되어 있는 경우, 구조물은내 외부의 온도차이로 인해서 열응력이 발생한다. 본 연구는 이러한 구조물에 강판 콘크리트 구조를 적용할 경우를 가정하여 보 형태의 강판 콘크리트 구조실험체에 온도하중을 재하한 상태에서 휨 내력 및 구조특성을 평가하고 추가적으로 실험체가 항복 시까지 하중을 가력하여 최종 휨내력을 평가하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.742-745
• /
• 2004

The FRP-concrete composite deck system has advantages of corrosion free and easy construction. The system is, however, comprised of two brittle materials, so that it suffers from inherent disadvantage of lack of ductility. In this study, some conceptual design is presented for preventing the brittle failure of FRP-concrete composite deck at ultimate load level. 4-point bending tests are performed for FRP-concrete composite beams using FRC(Fiber Reinforced Concrete). The specimens use the box-shape FRP member in the lower portion. Four types of concrete with different compressive strengths and ductilities including normal mortar and 3 FRCs are placed in the upper portion. Typical failure mode in the test is identified; Concrete compressive failure occurs first at the maximum moment region, and the interfacial debonding between FRP and concrete member proceeds. Finally, the tensile rupture of FRP member occurs. The specimen using FRC with the high compressive ductility of concrete fails with less brittle manner than other specimens. The reason is that the ductility from the concrete in compression prevents the sudden loss of load-carrying capacity after compressive concrete failure.

• Steel and Composite Structures
• /
• 제9권5호
• /
• pp.397-418
• /
• 2009

Eight panel specimens were tested in one-way bending to study the behaviour and capacity of composite slab joists consisting of cold-formed steel C-sections and concrete. Various shear transfer mechanisms were implemented on the C-section flange embedded in the concrete to provide the longitudinal shear resistance. Results showed that all specimens reached serviceability limit state while in elastic range and failure was ductile. Shear transfer achieved for all specimens ranged from 42 to 99% of a full transfer while specimens employed with shear transfer enhancements showed a greater percentage and therefore a higher strength compared with those relying only on surface bond to resist shear. The implementation of pre-drilled holes on the embedded flange of the steel C-section was shown to be most effective. The correlation study between the push-out and panel specimens indicated that the calculated moment capacity based on shear transfer resistance obtained from push-out tests was, on average, 10% lower than the experimental ultimate capacity of the panel specimen.

• Steel and Composite Structures
• /
• 제14권2호
• /
• pp.105-120
• /
• 2013

Flexural behavior of thin walled steel-concrete composite sections as cross sections for beams is investigated by conducting an experimental study supported by applicable analytical predictions. The experimental study consists of testing up to failure, simply supported beams of effective span 1440 mm under two point loading. The test specimens consisted of composite box and channel (with lip placed on tension side and compression side) sections, the behavior of which was compared with companion empty sections. To understand the role of shear connectors in developing the composite action, some of the composite sections were provided with novel simple bar type and conventional bolt type shear connectors in the shear zone of beams. Two RCC beams having equivalent ultimate moment carrying capacities as that of composite channel and box sections were also considered in the study. The study showed that the strength to weight ratio of composite beams is much higher than RCC beams and ductility index is also more than RCC and empty beams. The analytical predictions were found to compare fairly well with the experimental results, thereby validating the applicability of rigid plastic theory to cold-formed steel concrete composite beams.

• Steel and Composite Structures
• /
• 제14권2호
• /
• pp.133-153
• /
• 2013

The concrete-filled steel tube (CFT) columns have several benefits of high load-bearing capacity, inherent ductility and toughness because of the confinement effect of the steel tube on concrete and the restraining effect of the concrete on local buckling of steel tube. However, the experimental research into the behavior of square CFT columns consisting of high-strength steel and high-strength concrete is limited. Six full scale CFT specimens were tested under flexural moment. The CFT columns consisted of high-strength steel tubes ($f_y$ = 325 MPa, 555 MPa, 900 MPa) and high-strength concrete ($f_{ck}$ = 80 MPa and 120 MPa). The ultimate capacity of high strength square CFT columns was compared with AISC-LRFD design code. Also, this study was focused on investigating the effect of high-strength materials on the structural behavior and the mathematical models of the steel tube and concrete. Nonlinear fiber element analyses were conducted based on the material model considering the cyclic bending behavior of high-strength CFT members. The results obtained from the numerical analyses were compared with the experimental results. It was found that the numerical analysis results agree well with the experimental results.

• 한국농공학회지
• /
• 제32권3호
• /
• pp.79-86
• /
• 1990

Based on limited number of tests on reinforced wood beams using polymer mortar in this study, following conclusions were drawn ; 1.Reinforcing compression side of wood beam using polymer mortar was effective in reducing deflection. 2.By increasing thickness of polymer mortar, effective beam stiffness was improved, but energy absorption was reduced. 3.Polymer mortar reinforcement improved compressive strength and reduced strain in compression side of the beam. Therefore, it was possible to change the failure mode from by compression in control beam to by tension in composite beams. 4.The composite beams that have more than 2cm of polymer mortar layer did not perform well because a strain redistribution and separation of meterials at interface were induced in moment span. 5.To maximize the load carrying capacity of composite beam, it is necessary to make polymer mortar and wood behave together without failing at interface. To do this, it is needed to use a polymer mortar which has high strength with such elastic modulus that is closer to elastic modulus of wood. otherwise, it is recommended to use shear connectors at interface to prevent separation of materials under ultimate load.