• 한국농공학회지
• /
• 제30권1호
• /
• pp.38-49
• /
• 1988

This paper presented as follows results of laboratory model tests with various shaped footings on soil bed reinforced with the strips on the base of behaviour of soil structure according to the loads and triaxial test results reinforced with geotextiles. Their parameters studied were the effects on the bearing capacity of a footing of the first layer of reinforcement, horizontal and vertical spacing of layers, number of layers, tensile strength of reinforcement and iclination load to the vertical 1.Depending on the strip arrangement, ultimate bearing capacity values could be more improved than urreinforced soil and the failure of soil was that the soil structure was transfered from the macrospace to microspase and its arrangement, from edge to edge to face to face. 2.The reinforcement was produced the reinforcing effects due to controlling the value of factor of one and permeable reinforcement was never a barrier of drainage condition. 3.Strength ratio was decreased as a linear shape according to increment of saturation degree of soil used even though at the lower strength ratio, the value of M-factor was rot influenced on the strength ratio but impermeable reinforcement decreased the strength of bearing capacity. 4.Ultimate bearing capacity under the plane-strain condition was appeared a little larger than triaxial or the other theoretical formulars and the circular footing more effective. 5.The maximum reinforcing effects were obtained at U I B=o.5, B / B=3 and N=3, when over that limit only acting as a anchor, and same strength of fabric appeared larger reinforcing effects compared to the thinner one. 6.As the LDR increased, more and more BCR occurred and there was appeared a block action below Z / B=O.5, but over the value, decrement of BCR was shown linear relation, and no effects above one. 7.The coefficient of the inclination was shown of minimum at the three layers of fabrics, but the value of H / B related to the ultimate load was decreased as increment of inclination degree, even though over the value of 4.5 there wasn't expected to the reinforcing effects As a consequence of the effects on load inclination, the degree of inclination of 15 per cent was decreased the bearing capacity of 70 per cent but irnproved the effects of 45 per cent through the insertion of geotextile.

• 한국지반공학회논문집
• /
• 제20권3호
• /
• pp.85-96
• /
• 2004

본 연구는 점토층위의 모래지반에 위치하는 표면기초의 극한지지력에 대해 이론적으로 조사하였다. 실용적인 적용을 위하여 표면기초의 지지력에 관한 연구들에 대한 검토와 논의가 제시되며, 한계해석(Limit Analysis)의 운동학적 접근방법을 이용하여 정해의 극한 지지력이 계산되었다. 운동학적 해는 상한값이며 해의 정확성은 파괴메카니즘의 형상에 달려 있다. 이러한 방법은 설계도표를 만드는데 편리할 뿐만 아니라 물성치의 영향을 추정할 수 있다. 본 연구에서는 범용 유한요소해석 프로그램인 ABAQUS를 사용하여 탄소성 이론에 근거하여 극한지지력을 계산하였다. 운동학적 방범으로 계산된 결과와 유한요소 해석, 한계평형론에 근거한 몇몇 알려진 식들(Yamaguchi, Meyerhof와 Okamura 등)에 의한 결과를 비교하였다. 아울러, 운동학적 방법에 의한 제안식과 유한요소해석 결과와 한계평형해석 결과의 유효성에 대하여 검증하였다.

• 한국지반공학회지:지반
• /
• 제13권4호
• /
• pp.13-24
• /
• 1997

말뚝 해석 프로그램인 PAR에 의하여 말뚝의 극한 수직 및 수평 지지력을 예측할 수 있는 방법을 제안하였으며,현장에서 수행된 말뚝재하시험 결과들을 이용하여 PAR에 의한 사례연구를 수행하였다. PAR에 의해 해석된 말뚝의 극한지지력은 정재하시험에서 구한 지지력에 대하여 약 15%이내의 오차범위에 들었다. 또한, 강관말뚝들에 수행된 정재하시헙, 정.동재하시험 그리고 PDA 결과들을 비교하였으며, PAR에 의해 극한지지력을 예측하였다. PAR을 이용하면 말뚝의 축방향 하중의 분포를 예측할 수 있었으며, 여기서, 하중전이해석도 근사적으로 수행할 수 있었다.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1210-1218
• /
• 2018

A new type of earthquake-resisting element that consists of a steel plate shear wall with slits is introduced. The infill steel plate is divided into a series of vertical flexural links with vertical links. The steel plate shear walls absorb energy by means of in-plane bending deformation of the flexural links and the energy dissipation capacity of the plastic hinges formed at both ends of the flexural links when under lateral loads. In this paper, finite element analysis and experimental studies at low cyclic loadings were conducted on specimens with steel plate shear walls with multilayer slits. The effects caused by varied slit pattern in terms of slit design parameters on lateral stiffness, ultimate bearing capacity and hysteretic behavior of the shear walls were analyzed. Results showed that the failure mode of steel plate shear walls with a single-layer slit was more likely to be out-of-plane buckling of the flexural links. As a result, the lateral stiffness and the ultimate bearing capacity were relatively lower when the precondition of the total height of the vertical slits remained the same. Differently, the failure mode of steel plate shear walls with multilayer slits was prone to global buckling of the infill steel plates; more obvious tensile fields provided evidence to the fact of higher lateral stiffness and excellent ultimate bearing capacity. It was also concluded that multilayer specimens exhibited better energy dissipation capacity compared with single-layer plate shear walls.

• Geomechanics and Engineering
• /
• 제5권4호
• /
• pp.363-377
• /
• 2013

Any structure constructed on the earth is supported by the underlying soil. Foundation is an interfacing element between superstructure and the underlying soil that transmits the loads supported by the foundation including its self weight. Foundation design requires evaluation of safe bearing capacity along with both immediate and long term settlements. Weak and compressible soils are subjected to problems related to bearing capacity and settlement. The conventional method of design of footing requires sufficient safety against failure and the settlement must be kept within the allowable limit. These requirements are dependent on the bearing capacity of soil. Thus, the estimation of load carrying capacity of footing is the most important step in the design of foundation. A number of theoretical approaches, in-situ tests and laboratory model tests are available to find out the bearing capacity of footings. The reliability of any theory can be demonstrated by comparing it with the experimental results. Results from laboratory model tests on square footings resting on sand are presented in this paper. The variation of bearing capacity of sand below a model plate footing of square shape with variation in size, depth and the effect of permissible settlement are evaluated. A steel tank of size $900mm{\times}1200mm{\times}1000mm$ is used for conducting model tests. Bearing capacity factor $N_{\gamma}$ is evaluated and is compared with Terzaghi, Meyerhof, Hansen and Vesic's $N_{\gamma}$ values. From the experimental investigations it is found that, as the depth of sand cushion below the footing ($D_{sc}$) increases, ultimate bearing capacity and settlement values show an increasing trend up to a certain depth of sand cushion.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.940-947
• /
• 2005

In this study, model tests of soft silt soils(ML) and silt soils was polluted with wastewater and waste oil from factories($ML_p$). Distribution of displacement, bearing capacity comparing the test results with existing theoretical expressions and analyzing the test results, the following conclusions were obtained. It was found out that in soft silt soils the relationship of critical surcharge and undrained cohesion is $q_{cr}=4.14C_u$ and polluted silt soils $ML_p$ those are $q_{cr}=1.78C_u$, respectively and the relationship of ultimate capacities $q_{ult}=9.53C_u$ and undrained cohesion in polluted silt soils are $q_{ult}=4.39C_u$. Critical surcharge and ultimate capacity is less in polluted silt soils than in soft silt soils.

• Steel and Composite Structures
• /
• 제47권1호
• /
• pp.19-36
• /
• 2023

An experimental study of eleven PVC-FRP Confined Concrete (PFCC) column-Reinforced Concrete (RC) beam joints reinforced with Core Steel Tube (CST) under axial compression is carried out. All specimens are designed in accordance with the principle of "weak column and strong joint". The influences of FRP strips spacing, length and steel ratio of CST, height and stirrup ratio of joint on mechanical behavior are investigated. As the design anticipated, all specimens are destroyed by column failure. The failure mode of PFCC column-RC beam joint reinforced with CST is the yielding of longitudinal steel bars, CST and stirrups of column as well as the fracture of FRP strips and PVC tube. The ultimate bearing capacity decreases as FRP strips spacing or joint height increases. The effects of other three studied parameters on ultimate bearing capacity are not obvious. The strain development rules of longitudinal steel bars, PVC tube, FRP strips, column stirrups and CST are revealed. The effects of various studied parameters on stiffness are also examined. Additionally, an influence coefficient of joint height is introduced based on the regression analysis of test data, a theoretical formula for predicting bearing capacity is proposed and it agrees well with test data.

• 한국지반공학회논문집
• /
• 제19권2호
• /
• pp.237-246
• /
• 2003

항타말뚝은 진동과 소음같은 환경적인 문제점이 있다. 특히 대상 토질이 자갈, 호박돌, 풍화암으로 구성되어있다면 항타말뚝의 적용은 불가능하기 때문에 우리나라에서는 현장말뚝의 적용이 증가하고 있는 추세이다. 일반적으로 이론적인 공식에 의한 현장타설말뚝의 지지력은 과소하게 산정되는 것으로 알려져 있다. 본 연구에서는 기존에 제안된 국내외 지지력 산정식과 현장시험을 통한 실측데이터를 비교하기위해 광안대로와 수영 3호교의 암반에 근입된 현장 타설말뚝에 대한 정재하시험을 수행하였으며, 현장타설말뚝의 주변마찰력을 측정하기 위하여 변위계를 설치하였다. 현장시험을 통한 현장타설말뚝의 거동은 반복하중 재하시 완전한 탄성거동을 보였으므로 이는 실제말뚝의 극한지지력에 도달하지 못하였음을 입증한다. 이때 측정된 말뚝의 지지력이 이론식에 의하여 산정된 지지력보다 크게 산정되었다. 또한 실험에서 측정된 결과에 의하면 현장타설말뚝의 주된 지지력이 선단지지력이 아닌 주변마찰저항에 의한 것이라는 것을 보였다. 그리고 이와같은 결과에 의거하여 현장타설말뚝의 설계에 대한 몇가지 제안들을 도출하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.283-290
• /
• 2001

In this study, static Pile load tests and PDA for open-ended steel pipe pile($\phi$ = 609.6 mm, t = 14 mm) penetrated into the gravel layer(GP - GM) was accomplished and axial load distribution was measured. Based on the tests results, the ultimate bearing capacity and axial load bearing mode were examined. Also, the ultimate pile capacity was calculated by APIL $E^{PLUS}$./.

• Steel and Composite Structures
• /
• 제25권3호
• /
• pp.375-388
• /
• 2017

This paper presents a combined experimental, numerical, and analytical study on elliptical concrete-filled steel tubular (E-CFT) and rebar-stiffened elliptical concrete-filled steel tubular (RE-CFT) subjected to axial loading. ABAQUS was used to establish 3D finite element (FE) models for the composite columns and the FE results agreed well with the experimental results. It was found that the ultimate load-bearing capacity of RE-CFT stub columns was 20% higher than that of the E-CFT stub columns. Such improvement was attributed to the reinforcement effects from the internal rebar-stiffeners, which effectively enhanced the confinement effect on the core concrete, thereby significantly improved both the ultimate bearing capacity and the ductility of the E-CFT columns. Based on the results, equations were also established in this paper to predict the bearing capacities of E-CFT and RE-CFT stub columns under axial loading. The predicted results agreed well with both experimental and numerical results, and had much higher accuracy than other available methods.